Masaki Okamoto
Masaki Okamoto has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Hikaru Kobori
Faculty of Agriculture, Shizuoka University, Shizuoka, Japan
3 shared publications - Hirokazu Ito
Natl Inst Adv Ind Sci & Technol, Hiroshima, Japan
3 shared publications - Shinji Ogoe
Technology Development Center, TOCLAS Co., 1370 Nishiyama-cho, Nishi-ku, Hamamatsu, Shizuoka 432-8001, Japan
3 shared publications - Yoichi Kojima
Faculty of Agriculture, Shizuoka University
3 shared publications - Hirokazu Ito
Material Developing Section, Product Developing Department, Yamaha Livingtec Corporation, Hamamatsu 432-4001, Japan
2 shared publications - Kazushige Murayama
Shizuoka Univ, Fac Agr, Shizuoka, Japan
2 shared publications
Latest Publications
- Open Access
- 14 February 2019
- Published by MDPI AG in Journal of Composites Science
- Vol. 3 (1) , 20
Fatigue Performance of Wet and Dry Pulverized Wood Flour Reinforced PP Composites
In this paper, we exclusively studied the effects of dry and wet pulverization of different wood flours on the fatigue performance of polypropylene (PP)/wood flour (WF) composites. Wood flours obtained from cypress and Scots pine trees were pulverized in both dry and wet conditions at two different mill-plate gaps, 200 µm and 350 µm, and were used as reinforcement in PP matrices. Master batches of PP with different types of pulverized WF were compounded before processing in an extruder. The PP/WF composites of initial WF were also prepared for comparison. The prepared composites were analyzed by tensile and fatigue tests. It was found that the tensile properties of wood/polypropylene composites were affected by the pulverization of WF. Fatigue test results displayed that wet pulverization of short cypress flour had a negative effect on the fatigue life of PP/WF composites, while wet pulverization of long cypress flour and pine flour had a positive effect on the fatigue life of PP/WF composites.
- 14 February 2019
- Published by MDPI AG in Journal of Composites Science
- Vol. 3 (1) , 20
Open AccessFatigue Performance of Wet and Dry Pulverized Wood Flour Reinforced PP Composites
In this paper, we exclusively studied the effects of dry and wet pulverization of different wood flours on the fatigue performance of polypropylene (PP)/wood flour (WF) composites. Wood flours obtained from cypress and Scots pine trees were pulverized in both dry and wet conditions at two different mill-plate gaps, 200 µm and 350 µm, and were used as reinforcement in PP matrices. Master batches of PP with different types of pulverized WF were compounded before processing in an extruder. The PP/WF composites of initial WF were also prepared for comparison. The prepared composites were analyzed by tensile and fatigue tests. It was found that the tensile properties of wood/polypropylene composites were affected by the pulverization of WF. Fatigue test results displayed that wet pulverization of short cypress flour had a negative effect on the fatigue life of PP/WF composites, while wet pulverization of long cypress flour and pine flour had a positive effect on the fatigue life of PP/WF composites.
- 1 January 2019
- Published by Forest Products Society in Forest Products Journal
- Vol. 69 (2) , 141-147
Effects of Premixing Wood Flour with Compatibilizer with Different Characteristics on the Physical and Mechanical Properties of Wood/Plastic Composites
The addition of maleic anhydride (MA)-modified polypropylene (MAPP) as a compatibilizer increases mechanical and physical properties of wood/plastic composites (WPCs). It is thought that MA graft ratio (Gr), molecular weight (weight-average molecular weight [Mw]), and mixing methods of MAPP affect physical and mechanical properties of WPCs. However, evaluation, especially for mixing order, is not enough. The objective of this study was to investigate the effect of Gr and Mw of MAPP and its mixing methods on the mechanical and physical properties of WPCs. Two types of mixing methods were used: mixing the MAPP with the filler using a Henschel mixer before kneading with PP (premixing method) and mixing all of the materials at one time (one-step mixing method). The WPCs made with the premixing method had lower shear viscosity and higher flexural modulus than those made with the one-step mixing method. The particle size, moisture content, and surface morphology of fillers are thought to be more important in determining the shear viscosity of WPCs than the MAPP itself. The highest tensile, impact, and flexural strengths of WPCs were obtained in the WPC with premixing with low-Gr and high-Mw MAPP. It may be due to the effective reaction of the wood flour with MAPP and higher entanglement between the MAPP and PP. These results suggest that the premixing method could improve productivity and mechanical properties of WPCs.
- 1 January 2019
- Published by Forest Products Society in Forest Products Journal
- Vol. 69 (2) , 141-147
Effects of Premixing Wood Flour with Compatibilizer with Different Characteristics on the Physical and Mechanical Properties of Wood/Plastic Composites
The addition of maleic anhydride (MA)-modified polypropylene (MAPP) as a compatibilizer increases mechanical and physical properties of wood/plastic composites (WPCs). It is thought that MA graft ratio (Gr), molecular weight (weight-average molecular weight [Mw]), and mixing methods of MAPP affect physical and mechanical properties of WPCs. However, evaluation, especially for mixing order, is not enough. The objective of this study was to investigate the effect of Gr and Mw of MAPP and its mixing methods on the mechanical and physical properties of WPCs. Two types of mixing methods were used: mixing the MAPP with the filler using a Henschel mixer before kneading with PP (premixing method) and mixing all of the materials at one time (one-step mixing method). The WPCs made with the premixing method had lower shear viscosity and higher flexural modulus than those made with the one-step mixing method. The particle size, moisture content, and surface morphology of fillers are thought to be more important in determining the shear viscosity of WPCs than the MAPP itself. The highest tensile, impact, and flexural strengths of WPCs were obtained in the WPC with premixing with low-Gr and high-Mw MAPP. It may be due to the effective reaction of the wood flour with MAPP and higher entanglement between the MAPP and PP. These results suggest that the premixing method could improve productivity and mechanical properties of WPCs.
- 1 January 2018
- Published by Forest Products Society in Forest Products Journal
- Vol. 68 (4) , 398-404
Mechanical and Physical Properties of Wood–Plastic Composites Containing Cellulose Nanofibers Added to Wood Flour
Recently, the usage of wood–plastic composite (WPC) products has increased, mainly for exterior decking. The shape of fillers is one of the important factors deciding the mechanical and physical properties of WPCs. Surface-fibrillated wood flour (WF) improves the mechanical properties of WPCs, although it requires a lot of energy and time to produce the fibrous structure during the pulverization process. Therefore, the adsorptive interaction between cellulose nanofiber (CNF) and WF by hydrogen bonding was investigated. We considered that CNF could form the fibrous structures on the WF surface by mixing CNF and WF. Also, it is thought that the addition of CNF could increase mechanical and physical properties of WPC because CNF has better physical and mechanical properties than most other fibers. The objective of this study was to produce WF-CNF fillers and to evaluate the mechanical and physical properties of WPCs containing WF-CNF fillers. WF-CNF fillers could be produced by freeze-drying after mixing WF, CNF, and water. The fibrous structures on the WF surface were observed through scanning electron microscope images of WF-CNF filler containing 3 weight percent CNF. A WPC with WF-CNF filler containing 22 percent (by weight) WF and 3 percent (by weight) CNF showed improved mechanical properties compared with WPCs without CNF. The water absorption of WPCs containing CNF was found to decrease with increasing CNF content.
- 1 January 2018
- Published by Forest Products Society in Forest Products Journal
- Vol. 68 (4) , 398-404
Mechanical and Physical Properties of Wood–Plastic Composites Containing Cellulose Nanofibers Added to Wood Flour
Recently, the usage of wood–plastic composite (WPC) products has increased, mainly for exterior decking. The shape of fillers is one of the important factors deciding the mechanical and physical properties of WPCs. Surface-fibrillated wood flour (WF) improves the mechanical properties of WPCs, although it requires a lot of energy and time to produce the fibrous structure during the pulverization process. Therefore, the adsorptive interaction between cellulose nanofiber (CNF) and WF by hydrogen bonding was investigated. We considered that CNF could form the fibrous structures on the WF surface by mixing CNF and WF. Also, it is thought that the addition of CNF could increase mechanical and physical properties of WPC because CNF has better physical and mechanical properties than most other fibers. The objective of this study was to produce WF-CNF fillers and to evaluate the mechanical and physical properties of WPCs containing WF-CNF fillers. WF-CNF fillers could be produced by freeze-drying after mixing WF, CNF, and water. The fibrous structures on the WF surface were observed through scanning electron microscope images of WF-CNF filler containing 3 weight percent CNF. A WPC with WF-CNF filler containing 22 percent (by weight) WF and 3 percent (by weight) CNF showed improved mechanical properties compared with WPCs without CNF. The water absorption of WPCs containing CNF was found to decrease with increasing CNF content.
- Open Access
- 1 January 2016
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Materials and Mechanics Conference
- Vol. 2016, OS14-24
Effect of Additive on Tensile Properties of Wood-Plastic Composite
In recent years, plastics made from biomass feedstock are positively developed. There are a lot of forest resources in Japan,Wood - Plastic Composite (WPC) is attracting attention among them. In this study, in order to use WPC for industrial and machinery parts and products, two kinds of additive were added toWPC to improve tensile properties. In order to reveal the effects of additive on tensile strength and elongation at break, dynamic tensile tests were carried out using split Hopkinson pressure bar method. As a consequence, specimens do not change significantly such as whitening or necking, but the maximum stress and the elongation at break increased by 1.3 times by adding the additives.
- 1 January 2016
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Materials and Mechanics Conference
- Vol. 2016, OS14-24
Open AccessEffect of Additive on Tensile Properties of Wood-Plastic Composite
In recent years, plastics made from biomass feedstock are positively developed. There are a lot of forest resources in Japan,Wood - Plastic Composite (WPC) is attracting attention among them. In this study, in order to use WPC for industrial and machinery parts and products, two kinds of additive were added toWPC to improve tensile properties. In order to reveal the effects of additive on tensile strength and elongation at break, dynamic tensile tests were carried out using split Hopkinson pressure bar method. As a consequence, specimens do not change significantly such as whitening or necking, but the maximum stress and the elongation at break increased by 1.3 times by adding the additives.
- Open Access
Evaluation of Binding Effects in Wood Flour Board Containing Ligno-Cellulose Nanofibers
Wood-based materials are used extensively in residual construction worldwide. Most of the adhesives used in wood-based materials are derived from fossil resources, and some are not environmentally friendly. This study explores nanofiber technology as an alternative to such adhesives. Previous studies have shown that the three-dimensional binding effects of cellulose nanofiber (CNF), when mixed with wood flour, can significantly improve the physical and mechanical properties of wood flour board. In this study, ligno-cellulose nanofibers (LCNF) were fabricated by wet disk milling of wood flour. Composite boards of wood flour and LCNF were produced to investigate the binding effect(s) of LCNF. The fabrication of LCNF by disk milling was simple and effective, and its incorporation into wood flour board significantly enhanced the physical and mechanical properties of the board.
Open AccessEvaluation of Binding Effects in Wood Flour Board Containing Ligno-Cellulose Nanofibers
Wood-based materials are used extensively in residual construction worldwide. Most of the adhesives used in wood-based materials are derived from fossil resources, and some are not environmentally friendly. This study explores nanofiber technology as an alternative to such adhesives. Previous studies have shown that the three-dimensional binding effects of cellulose nanofiber (CNF), when mixed with wood flour, can significantly improve the physical and mechanical properties of wood flour board. In this study, ligno-cellulose nanofibers (LCNF) were fabricated by wet disk milling of wood flour. Composite boards of wood flour and LCNF were produced to investigate the binding effect(s) of LCNF. The fabrication of LCNF by disk milling was simple and effective, and its incorporation into wood flour board significantly enhanced the physical and mechanical properties of the board.