Nathan J. Kempema
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Nathan J. Kempema has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
Marshall B. Long
Yale University
3 shared publicationsBin Ma
GE Global Research Center,Niskayuna,USA
1 shared publication
Latest Publications
- 24 August 2016
- Published by Springer Nature in Applied Physics B
- Vol. 122 (9) , 232
Investigation of in-flame soot optical properties in laminar coflow diffusion flames using thermophoretic particle sampling and spectral light extinction
- 24 August 2016
- Published by Springer Nature in Applied Physics B
- Vol. 122 (9) , 232
Investigation of in-flame soot optical properties in laminar coflow diffusion flames using thermophoretic particle sampling and spectral light extinction
- Open Access
- 7 June 2016
- Published by Optica Publishing Group in Applied Optics
- Vol. 55 (17) , 4691-4698
Boundary condition thermometry using a thermographic-phosphor-coated thin filament
Thermographic phosphors (TPs) exhibit a temperature sensitive emission spectrum when excited with ultraviolet radiation. In this study, 14 μm diameter SiC fibers are coated with ZnO or Dy:YAG using a ceramic binder to a total diameter of μm. ZnO and Dy:YAG fibers were used to measure fiber temperatures in the range of 294–450 K and 450–1245 K, respectively. The coated fiber provides higher signal levels compared to TP particle seeding and is no more invasive than the commonly used thermocouple. A calibration is performed to relate fiber temperature to the ratio of luminescent signal collected within two different bands of the fiber emission spectrum. Temperature was measured along the inlet of a series of nitrogen diluted ethylene diffusion flames stabilized on the Yale coflow burner to determine suitable thermal boundary conditions for computational modeling. The boundary condition temperatures were derived from a spline fitting of data acquired from the two fiber types in order to obtain fiber temperature sensitivity from 294 to 1245 K. The peak near-burner temperature was found to be higher than ambient conditions and to increase and shift its location radially outward with increased fuel percentage.- 7 June 2016
- Published by Optica Publishing Group in Applied Optics
- Vol. 55 (17) , 4691-4698
Open AccessBoundary condition thermometry using a thermographic-phosphor-coated thin filament
Thermographic phosphors (TPs) exhibit a temperature sensitive emission spectrum when excited with ultraviolet radiation. In this study, 14 μm diameter SiC fibers are coated with ZnO or Dy:YAG using a ceramic binder to a total diameter of μm. ZnO and Dy:YAG fibers were used to measure fiber temperatures in the range of 294–450 K and 450–1245 K, respectively. The coated fiber provides higher signal levels compared to TP particle seeding and is no more invasive than the commonly used thermocouple. A calibration is performed to relate fiber temperature to the ratio of luminescent signal collected within two different bands of the fiber emission spectrum. Temperature was measured along the inlet of a series of nitrogen diluted ethylene diffusion flames stabilized on the Yale coflow burner to determine suitable thermal boundary conditions for computational modeling. The boundary condition temperatures were derived from a spline fitting of data acquired from the two fiber types in order to obtain fiber temperature sensitivity from 294 to 1245 K. The peak near-burner temperature was found to be higher than ambient conditions and to increase and shift its location radially outward with increased fuel percentage. - Open Access
- 2 October 2014
- Published by Optica Publishing Group in Applied Optics
- Vol. 53 (29) , 6688-6697
Quantitative Rayleigh thermometry for high background scattering applications with structured laser illumination planar imaging
This work demonstrates structured laser illumination planar imaging (SLIPI) for Rayleigh thermometry with high background scattering. Two coherent laser beams were crossed to produce an interference pattern, from which the modulated Rayleigh signal was collected. The modulated signal serves as a signature that identifies information about Rayleigh scattering from the probe volume against additional contributions in the image from background scattering. This work shows that the structured nature of the illumination allows for a simplified background correction. The experimental approach is validated in a non-premixed methane/air flame, and the temperature is found to be in excellent agreement with previous experimental and computational results. Rayleigh SLIPI is then applied to a high background scattering application as part of the full-field temperature measurement of sooting non-premixed ethylene/air flames. For these flames, standard Rayleigh background corrections are impossible since scattering from soot just outside the field of view is the main source of the background. Good agreement is found between SLIPI and intensity-ratio thin-filament pyrometry-derived temperature along their adjoining interface in the flame.
- 2 October 2014
- Published by Optica Publishing Group in Applied Optics
- Vol. 53 (29) , 6688-6697
Open AccessQuantitative Rayleigh thermometry for high background scattering applications with structured laser illumination planar imaging
This work demonstrates structured laser illumination planar imaging (SLIPI) for Rayleigh thermometry with high background scattering. Two coherent laser beams were crossed to produce an interference pattern, from which the modulated Rayleigh signal was collected. The modulated signal serves as a signature that identifies information about Rayleigh scattering from the probe volume against additional contributions in the image from background scattering. This work shows that the structured nature of the illumination allows for a simplified background correction. The experimental approach is validated in a non-premixed methane/air flame, and the temperature is found to be in excellent agreement with previous experimental and computational results. Rayleigh SLIPI is then applied to a high background scattering application as part of the full-field temperature measurement of sooting non-premixed ethylene/air flames. For these flames, standard Rayleigh background corrections are impossible since scattering from soot just outside the field of view is the main source of the background. Good agreement is found between SLIPI and intensity-ratio thin-filament pyrometry-derived temperature along their adjoining interface in the flame.