Laleh Rajabi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Laleh Rajabi has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
A. A. Derakhshan
Islamic Azad University
4 shared publicationsAli Ashraf Derakhshan
Chemistry Department, Faculty of Science, Ilam University, Ilam, Iran
4 shared publicationsA. R. Kurdian
Razi University
2 shared publicationsSh. Ghorabi
2 shared publicationsA. Rostamabadi
1 shared publication- Arash Ghorbani-Choghamarani
Department of Organic Chemistry, Faculty of Chemistry and Petroleum Sciences, Bu-Ali Sina University, Hamedan, Iran
1 shared publication
Latest Publications
- 25 October 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 135 (7)
Biofouling alleviation and flux enhancement of electrospun PAN microfiltration membranes by embedding of para‐aminobenzoate alumoxane nanoparticles
Membrane bioreactor (MBR) as a hybrid technology for wastewater treatment is becoming more popular for wastewater treatment. However, membrane fouling has hindered the widespread application of MBRs. Many efforts have been done for fouling mitigation. In this study, high flux and antifouling microfiltration membranes with unique surface structure, high surface porosity, and permeability were prepared by electrospinning technique. Initially, the optimum thickness of electrospun polyacrylonitrile (PAN) membranes was determined and then, electrospun PAN membrane at optimum thickness were prepared by embedding para‐aminobenzoate alumoxane (PABA) nanoparticles at different concentrations. The effect of PABA nanoparticles on membrane performance was investigated. To investigate the characterization of the prepared membranes Fourier transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy, energy dispersive X‐ray spectroscopy, and water contact angle measurement were employed. The flux recovery ratio results revealed that the antifouling properties of the electrospun PAN membrane were enhanced by modification. The 3 wt % electrospun PABA embedded PAN had the best permeability, hydrophilicity, and antifouling properties among the fabricated membranes and showed remarkable reusability during filtration. The results obtained suggested that the high flux and antifouling electrospun PAN membranes embedded PABA nanoparticles could be used as MBR membranes. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 45738.
- 25 October 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 135 (7)
Biofouling alleviation and flux enhancement of electrospun PAN microfiltration membranes by embedding of para‐aminobenzoate alumoxane nanoparticles
Membrane bioreactor (MBR) as a hybrid technology for wastewater treatment is becoming more popular for wastewater treatment. However, membrane fouling has hindered the widespread application of MBRs. Many efforts have been done for fouling mitigation. In this study, high flux and antifouling microfiltration membranes with unique surface structure, high surface porosity, and permeability were prepared by electrospinning technique. Initially, the optimum thickness of electrospun polyacrylonitrile (PAN) membranes was determined and then, electrospun PAN membrane at optimum thickness were prepared by embedding para‐aminobenzoate alumoxane (PABA) nanoparticles at different concentrations. The effect of PABA nanoparticles on membrane performance was investigated. To investigate the characterization of the prepared membranes Fourier transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy, energy dispersive X‐ray spectroscopy, and water contact angle measurement were employed. The flux recovery ratio results revealed that the antifouling properties of the electrospun PAN membrane were enhanced by modification. The 3 wt % electrospun PABA embedded PAN had the best permeability, hydrophilicity, and antifouling properties among the fabricated membranes and showed remarkable reusability during filtration. The results obtained suggested that the high flux and antifouling electrospun PAN membranes embedded PABA nanoparticles could be used as MBR membranes. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 45738.
- 15 September 2017
- Published by Springer Nature in Journal of the Australian Ceramic Society
- Vol. 54 (1) , 23-32
Fabrication of a porous bulky layer ceramic nanofibrous composite with electromagnetic wave-absorbing properties
- 15 September 2017
- Published by Springer Nature in Journal of the Australian Ceramic Society
- Vol. 54 (1) , 23-32
Fabrication of a porous bulky layer ceramic nanofibrous composite with electromagnetic wave-absorbing properties
- 28 September 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (97) , 94314-94324
Copper–Schiff base alumoxane: a new and reusable mesoporous nano catalyst for Suzuki–Miyaura and Stille C–C cross-coupling reactions
Herein for the first time, a mesoporous copper nano catalyst (SBA–Cu2+) were simply synthesized through immobilization of Cu2+ on surface of Schiff base alumoxane support. This nano catalyst was characterized by various techniques such as FT-IR, X-ray map, TG-DTA, BET, SEM, SEM-EDS, TEM, ICP-OES and XRD. The characterization results indicated that SBA–Cu2+ nanoflakes with 331.47 m2 g−1 specific surface area are thermally stable up to 306 °C. The SBA–Cu2+ nano catalysts showed significant activity for Suzuki–Miyaura and Stille cross-coupling reactions with good efficiency and reusability. In addition, the nanocatalyst could be recovered and reused several times without significant loss of its catalytic activity. Copper leaching from SBA–Cu2+ is very negligible for this coupling reaction.
- 28 September 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (97) , 94314-94324
Copper–Schiff base alumoxane: a new and reusable mesoporous nano catalyst for Suzuki–Miyaura and Stille C–C cross-coupling reactions
Herein for the first time, a mesoporous copper nano catalyst (SBA–Cu2+) were simply synthesized through immobilization of Cu2+ on surface of Schiff base alumoxane support. This nano catalyst was characterized by various techniques such as FT-IR, X-ray map, TG-DTA, BET, SEM, SEM-EDS, TEM, ICP-OES and XRD. The characterization results indicated that SBA–Cu2+ nanoflakes with 331.47 m2 g−1 specific surface area are thermally stable up to 306 °C. The SBA–Cu2+ nano catalysts showed significant activity for Suzuki–Miyaura and Stille cross-coupling reactions with good efficiency and reusability. In addition, the nanocatalyst could be recovered and reused several times without significant loss of its catalytic activity. Copper leaching from SBA–Cu2+ is very negligible for this coupling reaction.
- 1 February 2015
- Published by Elsevier in Journal of Hazardous Materials
- Vol. 283, 276-291
Statistical investigation of lead removal with various functionalized carboxylate ferroxane nanoparticles
- 1 February 2015
- Published by Elsevier in Journal of Hazardous Materials
- Vol. 283, 276-291
Statistical investigation of lead removal with various functionalized carboxylate ferroxane nanoparticles
- 4 October 2014
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 23 (11) , 855-867
Dynamic cure kinetics of epoxy/TiO2/MWCNT hybrid nanocomposites
- 4 October 2014
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 23 (11) , 855-867
Dynamic cure kinetics of epoxy/TiO2/MWCNT hybrid nanocomposites
- 8 January 2014
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 23 (3) , 203-215
Epoxy/alumoxane and epoxy/boehmite nanocomposites: cure behavior, thermal stability, hardness and fracture surface morphology
- 8 January 2014
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 23 (3) , 203-215
Epoxy/alumoxane and epoxy/boehmite nanocomposites: cure behavior, thermal stability, hardness and fracture surface morphology
- 1 September 2012
- Published by American Scientific Publishers in Journal of Nanoengineering and Nanomanufacturing
- Vol. 2 (3) , 291-303
Epoxy/Functionalized MWCNT Nanocomposites: Cure Behaviour, Thermal Stability, Mechanical Properties and Fracture Morphology
Multi-walled carbon nanotubes were chemically functionalized with the aromatic amine functional groups. Two sets of epoxy/MWCNT nanocomposites were fabricated, each containing various amounts (0.1, 0.2, 0.3, 0.4 and 0.5 wt%) of unfunctionalized and functionalized MWCNTs respectively. The nanocomposites were subjected to TG-DTA, hardness and tensile tests in order to study the effect of functionalization of carbon nanotubes on thermal stability, cure behavior, hardness and tensile parameters of the samples. Tensile fracture morphology was also studied from SEM micrographs. The increasing effect of MWCNT and f-MWCNT on peak exothermic temperature of all the systems indicated the retarding effect of MWCNT imposed on the curing process of epoxy/hardener. However, the addition of nanotubes had a converse effect on the polymer network formation. No considerable effect on the thermal stability of any of the nanocomposites was observed. The results obtained from the tensile tests matched well with observations from the SEM micrographs. The epoxy nanocomposites made of functionalized MWCNTs had higher tensile strength as compared to the ones made with the unfunctionalized MWCNTs. Physical interaction occurred between the epoxy matrix and the unfunctionalized CNTs, whereas, due to the functional groups on the surfaces of the functionalized MWCNTs, the interaction between the epoxy matrix and the f-CNTs was of chemical type (covalent bonds).
- 1 September 2012
- Published by American Scientific Publishers in Journal of Nanoengineering and Nanomanufacturing
- Vol. 2 (3) , 291-303
Epoxy/Functionalized MWCNT Nanocomposites: Cure Behaviour, Thermal Stability, Mechanical Properties and Fracture Morphology
Multi-walled carbon nanotubes were chemically functionalized with the aromatic amine functional groups. Two sets of epoxy/MWCNT nanocomposites were fabricated, each containing various amounts (0.1, 0.2, 0.3, 0.4 and 0.5 wt%) of unfunctionalized and functionalized MWCNTs respectively. The nanocomposites were subjected to TG-DTA, hardness and tensile tests in order to study the effect of functionalization of carbon nanotubes on thermal stability, cure behavior, hardness and tensile parameters of the samples. Tensile fracture morphology was also studied from SEM micrographs. The increasing effect of MWCNT and f-MWCNT on peak exothermic temperature of all the systems indicated the retarding effect of MWCNT imposed on the curing process of epoxy/hardener. However, the addition of nanotubes had a converse effect on the polymer network formation. No considerable effect on the thermal stability of any of the nanocomposites was observed. The results obtained from the tensile tests matched well with observations from the SEM micrographs. The epoxy nanocomposites made of functionalized MWCNTs had higher tensile strength as compared to the ones made with the unfunctionalized MWCNTs. Physical interaction occurred between the epoxy matrix and the unfunctionalized CNTs, whereas, due to the functional groups on the surfaces of the functionalized MWCNTs, the interaction between the epoxy matrix and the f-CNTs was of chemical type (covalent bonds).
- 1 September 2012
- Published by American Scientific Publishers in Journal of Nanoengineering and Nanomanufacturing
- Vol. 2 (3) , 259-267
Cure Behavior, Thermal Stability and Mechanical Properties of Epoxy/Alumina Nanocomposites
This research work presents the effect of the untreated alumina nanoparticles in various amounts on cure behavior, thermal stability, hardness and tensile parameters and dynamic mechanical properties of epoxy/alumina nanocomposites. SEM micrographs were taken to monitor the extent of dispersion of the nano particles in the polymer matrix. Addition of alumina nanoparticles to the epoxy, had an accelerating effect on the curing process and a converse effect on the polymer network formation, but did not change the autocatalytic cure reaction mechanism of the epoxy/amine hardener system. Presence of the nanoparticles also improved thermal stability of the nanocomposites. Hardness of the composite containing 0.5 wt% nano alumina particles increased with respect to the resin system without any alumina content, further increase of the amount of the nano particles decreased the hardness of the nanocomposites respectively with small variations. This result matched well with the results obtained from the cure studies. Addition of nano alumina particles had an increasing effect on tensile strength and varying its amount to higher values kept on further increasing the corresponding property. The presence of rigid alumina nanoparticles increased the elastic modulus of the nanocomposites. Presence of alumina nano particles also increased the glass transition temperature of all the nanocomposites due to the increase of the interfacial adhesion and uniform dispersion of nano particles in the epoxy matrix, also confirmed from the SEM micrographs.
- 1 September 2012
- Published by American Scientific Publishers in Journal of Nanoengineering and Nanomanufacturing
- Vol. 2 (3) , 259-267
Cure Behavior, Thermal Stability and Mechanical Properties of Epoxy/Alumina Nanocomposites
This research work presents the effect of the untreated alumina nanoparticles in various amounts on cure behavior, thermal stability, hardness and tensile parameters and dynamic mechanical properties of epoxy/alumina nanocomposites. SEM micrographs were taken to monitor the extent of dispersion of the nano particles in the polymer matrix. Addition of alumina nanoparticles to the epoxy, had an accelerating effect on the curing process and a converse effect on the polymer network formation, but did not change the autocatalytic cure reaction mechanism of the epoxy/amine hardener system. Presence of the nanoparticles also improved thermal stability of the nanocomposites. Hardness of the composite containing 0.5 wt% nano alumina particles increased with respect to the resin system without any alumina content, further increase of the amount of the nano particles decreased the hardness of the nanocomposites respectively with small variations. This result matched well with the results obtained from the cure studies. Addition of nano alumina particles had an increasing effect on tensile strength and varying its amount to higher values kept on further increasing the corresponding property. The presence of rigid alumina nanoparticles increased the elastic modulus of the nanocomposites. Presence of alumina nano particles also increased the glass transition temperature of all the nanocomposites due to the increase of the interfacial adhesion and uniform dispersion of nano particles in the epoxy matrix, also confirmed from the SEM micrographs.
- 3 January 2012
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 21 (2) , 121-130
Effects of three surfactant types of anionic, cationic and non-ionic on tensile properties and fracture surface morphology of epoxy/MWCNT nanocomposites
- 3 January 2012
- Published by Springer Nature in Iranian Polymer Journal
- Vol. 21 (2) , 121-130
Effects of three surfactant types of anionic, cationic and non-ionic on tensile properties and fracture surface morphology of epoxy/MWCNT nanocomposites
- 1 August 2011
- Published by American Scientific Publishers in Journal of Nanoengineering and Nanomanufacturing
- Vol. 1 (2) , 182-187
Synthesis of Boehmite-Like Nanorods Through Inverse Phase Transformation
- 1 August 2011
- Published by American Scientific Publishers in Journal of Nanoengineering and Nanomanufacturing
- Vol. 1 (2) , 182-187
Synthesis of Boehmite-Like Nanorods Through Inverse Phase Transformation