Amit Kumar Gupta
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Amit Kumar Gupta has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
- Swadesh Kumar Singh
GRIET
8 shared publications - Nitin Kotkunde
Mechanical Engineering Department, BITS-Pilani, Hyderabad Campus, Hyderabad, India
4 shared publications - Amrita Priyadarshini
Department of Mechanical Engineering, Birla Institute of Technology & Science Pilani, Hyderabad Campus, Hyderabad 500078, India
3 shared publications Aditya Balu
2 shared publicationsKolla Lakshman Rao
2 shared publicationsKrishna Toshniwal
Birla Institute of Technology and Science, Hyderabad, 500090, India
2 shared publications
Latest Publications
- Open Access
- 23 January 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (3)
Corrosion Behavior Studies on Heat-Treated Severely Plastically Deformed Nimonic 263 Alloy
This study investigates the hot corrosion and electro-corrosion behavior of heat-treated Nimonic 263 alloy, which has been severely plastically deformed through constrained groove pressing (CGP).Renowned for its robustness in high-temperature applications, the alloy's responses to aggressive environments were assessed, focusing on hot corrosion and electro-corrosion. For the hot corrosion analysis, the alloy was exposed to a salt mixture of Na 2 SO 4 (87.5 wt.%), NaCl (5 wt.%), and NaVO 3 (7.5 wt.%). Over a 100-hour duration at 800°C, the corrosion kinetics revealed varying degrees of aggressiveness, with the heat-treated CGPed specimens exhibiting higher reactivity compared to the asreceived specimens. The formation of multiple compounds, including oxides, sulfides, and vanadate compounds, was observed. Volatile compounds like NaClO 3 and CrMoO 3 contributed to mass loss.Electrochemical analyses were conducted on as-received, CGPed, and heat-treated CGPed specimens.The findings revealed that the heat-treated samples exhibited a significant enhancement in polarization resistance, ranging from 42% to 154%, with the maximum resistance observed in specimens treated at 700°C.
- 23 January 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (3)
Open AccessCorrosion Behavior Studies on Heat-Treated Severely Plastically Deformed Nimonic 263 Alloy
This study investigates the hot corrosion and electro-corrosion behavior of heat-treated Nimonic 263 alloy, which has been severely plastically deformed through constrained groove pressing (CGP).Renowned for its robustness in high-temperature applications, the alloy's responses to aggressive environments were assessed, focusing on hot corrosion and electro-corrosion. For the hot corrosion analysis, the alloy was exposed to a salt mixture of Na 2 SO 4 (87.5 wt.%), NaCl (5 wt.%), and NaVO 3 (7.5 wt.%). Over a 100-hour duration at 800°C, the corrosion kinetics revealed varying degrees of aggressiveness, with the heat-treated CGPed specimens exhibiting higher reactivity compared to the asreceived specimens. The formation of multiple compounds, including oxides, sulfides, and vanadate compounds, was observed. Volatile compounds like NaClO 3 and CrMoO 3 contributed to mass loss.Electrochemical analyses were conducted on as-received, CGPed, and heat-treated CGPed specimens.The findings revealed that the heat-treated samples exhibited a significant enhancement in polarization resistance, ranging from 42% to 154%, with the maximum resistance observed in specimens treated at 700°C.
- 6 January 2023
- Published by Elsevier in Materials Today Communications
- Vol. 34
A review on superplastic forming of Ti-6Al-4V and other titanium alloys
- 6 January 2023
- Published by Elsevier in Materials Today Communications
- Vol. 34
A review on superplastic forming of Ti-6Al-4V and other titanium alloys
- 25 September 2022
- Published by Springer Nature
- p. 331-338
Topology Optimization for Designing a Wheel Rim
- 25 September 2022
- Published by Springer Nature
- p. 331-338
Topology Optimization for Designing a Wheel Rim
- Open Access
- 19 April 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 18, 4042-4059
Ballistic performance of functionally graded boron carbide reinforced Al – Zn – Mg – Cu alloy
- 19 April 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 18, 4042-4059
Open AccessBallistic performance of functionally graded boron carbide reinforced Al – Zn – Mg – Cu alloy
- 24 September 2021
- Published by Springer Nature in Shape Memory and Superelasticity
- Vol. 7 (4) , 503-514
Microstructural, Mechanical, and Superelastic Behavior of Thermo-Mechanically Processed Nitinol Alloy
- 24 September 2021
- Published by Springer Nature in Shape Memory and Superelasticity
- Vol. 7 (4) , 503-514
Microstructural, Mechanical, and Superelastic Behavior of Thermo-Mechanically Processed Nitinol Alloy
- Open Access
- 10 March 2021
- Published by Defence Scientific Information and Documentation Centre in Defence Science Journal
- Vol. 71 (2) , 162-170
Experimental Investigations on The Effect of Tungsten Content on the Machining Behaviour of Tungsten Heavy Alloys
The present work attempts to assess the machinability of tungsten heavy alloys (WHAs) with varying tungsten content in terms of different machining characteristics such as chip thickness, material removal rate, cutting force and surface roughness under varied cutting conditions. The feed rate is found to have major influence on the machining characteristics; whereas the effect of rake angle appears to be marginal. With increase in W content both cutting force and material removal rate increase whereas surface roughness decreases. Since WHAs are difficult to machine, an additional objective of the study is to optimize machining parameters. An optimal balance of the experimental cutting parameters using Grey relational analysis has been achieved, which can be effectively employed for the machining of the alloys with close dimensional tolerances and desirable surface finish.
- 10 March 2021
- Published by Defence Scientific Information and Documentation Centre in Defence Science Journal
- Vol. 71 (2) , 162-170
Open AccessExperimental Investigations on The Effect of Tungsten Content on the Machining Behaviour of Tungsten Heavy Alloys
The present work attempts to assess the machinability of tungsten heavy alloys (WHAs) with varying tungsten content in terms of different machining characteristics such as chip thickness, material removal rate, cutting force and surface roughness under varied cutting conditions. The feed rate is found to have major influence on the machining characteristics; whereas the effect of rake angle appears to be marginal. With increase in W content both cutting force and material removal rate increase whereas surface roughness decreases. Since WHAs are difficult to machine, an additional objective of the study is to optimize machining parameters. An optimal balance of the experimental cutting parameters using Grey relational analysis has been achieved, which can be effectively employed for the machining of the alloys with close dimensional tolerances and desirable surface finish.
- 19 February 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing-Green Technology
- Vol. 9 (2) , 459-472
Tin Layer as a Solid Lubricant for Cold Tube Drawing Processes
- 19 February 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing-Green Technology
- Vol. 9 (2) , 459-472
Tin Layer as a Solid Lubricant for Cold Tube Drawing Processes
- 7 October 2020
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 143 (2) , 1-11
An Alternate Approach to SHPB Tests to Compute Johnson-Cook Material Model Constants for 97 WHA at High Strain Rates and Elevated Temperatures Using Machining Tests
With advances in computational techniques, numerical methods such as finite element method (FEM) are gaining much of the popularity for analysis as these substitute the expensive trial and error experimental techniques to a great extent. Consequently, selection of suitable material models and determination of precise material model constants are one of the prime concerns in FEM. This paper presents a methodology to determine the Johnson-Cook constitutive equation constants (JC constants) of 97 W Tungsten heavy alloys (WHAs) under high strain rate conditions using machining tests in conjunction with Oxley’s predictive model and particle swarm optimization (PSO) algorithm. Currently, availability of the high strain rate data for 97 WHA are limited and consequently, JC constants for the same are not readily available. The overall methodology includes determination of three sets of JC constants, namely, M1 and M2 from the Split-Hopkinson pressure bar (SHPB) test data available in literature by using conventional optimization technique and artificial bee colony (ABC) algorithm, respectively. However, M3 is determined from machining tests using inverse identification method. To validate the identified JC constants, machining outputs (cutting forces, temperature, and shear strain) are predicted using finite element (FE) model by considering M1, M2, and M3 as input under different cutting conditions and then validated with corresponding experimental values. The predicted outputs obtained using JC constants M3 closely matched with that of the experimental ones with error percentage well within 10%.
- 7 October 2020
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 143 (2) , 1-11
An Alternate Approach to SHPB Tests to Compute Johnson-Cook Material Model Constants for 97 WHA at High Strain Rates and Elevated Temperatures Using Machining Tests
With advances in computational techniques, numerical methods such as finite element method (FEM) are gaining much of the popularity for analysis as these substitute the expensive trial and error experimental techniques to a great extent. Consequently, selection of suitable material models and determination of precise material model constants are one of the prime concerns in FEM. This paper presents a methodology to determine the Johnson-Cook constitutive equation constants (JC constants) of 97 W Tungsten heavy alloys (WHAs) under high strain rate conditions using machining tests in conjunction with Oxley’s predictive model and particle swarm optimization (PSO) algorithm. Currently, availability of the high strain rate data for 97 WHA are limited and consequently, JC constants for the same are not readily available. The overall methodology includes determination of three sets of JC constants, namely, M1 and M2 from the Split-Hopkinson pressure bar (SHPB) test data available in literature by using conventional optimization technique and artificial bee colony (ABC) algorithm, respectively. However, M3 is determined from machining tests using inverse identification method. To validate the identified JC constants, machining outputs (cutting forces, temperature, and shear strain) are predicted using finite element (FE) model by considering M1, M2, and M3 as input under different cutting conditions and then validated with corresponding experimental values. The predicted outputs obtained using JC constants M3 closely matched with that of the experimental ones with error percentage well within 10%.