APAmrita Priyadarshini

Amrita Priyadarshini

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Amrita Priyadarshini has a total of 31 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Combining Sensor Fusion and a Machine Learning Framework for Accurate Tool Wear Prediction During Machining

    by Swathi Kotha Amarnath, Vamsi Inturi, Sabareesh Geetha Rajasekharan, Amrita Priyadarshini

    Effective cutting tool condition monitoring (TCM) is critical for achieving precision, cost efficiency, and minimizing unplanned downtime. This study proposes a sophisticated sensor fusion framework for accurate tool fault prediction during machining. Experimental data were collected while turning AISI 410-grade steel bars with uncoated carbide inserts under dry-cutting conditions. Force and vibration signals were captured across five tool health states (one healthy and four faulty) using a sensor network and data acquisition systems. The raw signals were decomposed using discrete wavelet transform, and key statistical features were extracted. Three distinct input datasets are constructed: Dataset I comprises statistical parameters extracted exclusively from the force signals, Dataset II consists of statistical parameters derived from the vibration signals, and Dataset III integrates the individual statistical parameters from both force and vibration signals through feature-level fusion. These datasets are then utilized for training ML classifiers (Support Vector Machine, Random Forest, and Naive Bayes) to perform feature learning and subsequent classification. Among the considered classifiers, the RF classifier yielded better classification accuracies of 96% and 97% while discriminating among the tool health scenarios through dataset I and II. Also, the RF and SVM classifiers achieved a classification accuracy of 98% and 88% in distinguishing tool health scenarios for dataset III. This method demonstrates exceptional suitability for real-time, in situ fault diagnostics and provides a strong foundation for developing online TCM systems, advancing the objectives of Industry 4.0 and smart manufacturing.


  • Open Access

    Machining and Tribological Characterisation of Uncoated and Coated Carbide Inserts while Turning Tungsten Heavy Alloy

    by Sreejith S, Amrita Priyadarshini, Phaneendra Kirna Chaganti, G Prabhu

    Tungsten heavy alloys are high density alloys containing 80 to 98 wt.% tungsten and the balance is a matrix made of relatively low melting elements such as copper, nickel and iron. These alloys are used as radiation shields, CG adjusters and also in armour piercing ammunition. Machining these alloys to close tolerances and finish leads to excessive tool wear, surface damage and hence proves to be a challenging task. This study focuses on turning operation carried out under dry and wet cutting conditions using three different commercially available cemented carbide inserts. Three different feed rates have been used at a constant depth of cut and cutting speed. The best possible cemented carbide tooling solution for machining tungsten heavy alloys has been determined based on the surface finish obtained, chip geometry, cutting forces, and machining temperature. The observations made during machining are correlated to the tribological behavior of the inserts and the alloy with the help of pin-on disc tests. Coated cemented carbide inserts provide surface roughness values lower than 1 µm under finish turning conditions. On the other hand, PVD coated inserts give consistently better results over different feed rates and are found to experience lower tool wear for the specific cutting conditions. Analytical tool wear model suggests better tool life for the PVD coated insert.

  • A comparative study on the effect of grid printing methods and camera hardware in automatic strain measurement through CGA

    by Pankaj Wankhede, K Mahesh, Suresh Kurra, Amrita Priyadarshini, Nitin Kotkunde

    Strain analysis is an important step in sheet metal forming operations to identify the potential locations of failure. Circle grid analysis is a widely used method to evaluate the strains in sheet metal forming, where deformed circles on a formed component are measured to evaluate the strains at different locations. In this paper, two different USB cameras are used to capture the images of the deformed grids. The images are processed using the in-house software developed in MATLAB for strain measurement. The effect of image acquisition hardware and grid printing methods on strain measurement accuracy has been analyzed. For this, the sheets are printed with circular grids by screen printing, laser engraving, and electrochemical etching. The sheets are then deformed in incremental forming to produce different levels of strain in the formed components. The deformed grids on the formed components are captured using proposed USB cameras with appropriate attachments and processed by in-house strain measurement software. The strain measured using proposed hardware and software is also compared with the commercial strain measurement system. The mean absolute percentage error in strain measurement with the proposed USB cameras was found to be 0.671 and 0.761. The statistical results show that there is no evidence to support the hypothesis that the two hardware perform differently on average. Hence, the proposed hardware and software can be used in industry and research laboratories for strain analysis in sheet metal forming operations.


  • Multi-Objective Optimization of Lobed Enclosure for Wind Turbine Applications Using Gray Relation Analysis

    by L. Ramayee, K. Supradeepan, S. Sreejith, Amrita Priyadarshini

    Lobed mixer wind turbines have the lobed mixer added around the turbine, enhancing the wind power compared to conventional wind turbines. This article aims to design a bare lobed mixer that satisfies the multi-objectives of maximizing average throat (where the turbine blades are fixed) velocity uavg and minimizing drag coefficient Cd. The objectives are set considering that a bare enclosure with a higher uavg will produce higher power output when the turbine is included. Numerical simulations were performed to understand the flow characteristics of the non-lobed and lobed enclosure using ansys fluent. The lobed mixer angle was varied using a one factor at a time (OFAT) approach, and the angle with the highest uavg/Cd was found. Then, by fixing the lobed mixer angle, multi-objective gray relation analysis (GRA) was used to optimize the lobed mixer’s three geometrical parameters, such as the number of lobes, lobe width, and lobe height simultaneously. The GRA results show that lobe height is the most significant parameter affecting throat velocity and drag coefficient, and the optimum combination which fulfills both objectives were found. The most significant lobe height was further analyzed to improve uavg using the OFAT approach. Then in the optimized enclosure, the plug/center body was included at the axis, and the performance of two different plug geometries was compared. NACA 0024 was found to be better plug cross section. Thus, the proposed design of lobed enclosure helps to enhance the average velocity as 1.76 times the freestream velocity and reduce the drag coefficient by 5.43% than the case without lobes. Hence lobed mixer is a better option to use as an enclosure, especially to reduce the drag forces.


  • Synthesis of TiO2 coatings by thermal oxidation with a suitable cooling process for improved wettability

    by Chennakesava Sai Pitchi, Amrita Priyadarshini, Suresh Kumar Reddy Narala

    The present research aims to develop a suitable cooling strategy in conjunction with the oxidation time during thermal oxidation to develop a TiO2 layer on Ti–6Al–4V substrate that could improve wettability and promote osseointegration. The study was carried out to verify if a change in cooling methods in conjunction with the change in oxidation time during thermal oxidation could influence the wettability of oxide layers for bio-medical implants made of titanium alloys. The prepared specimens are subjected to XRD, XPS, surface roughness and wettability studies to study the effect of cooling methods. A parameter named polycrystallinity index was introduced to explain the relationship between relative intensities in XRD and wettability. Oil cooling with 8 h oxidation was found to be the most favourable one out of all the conditions considered in the present work that would achieve enhanced wettability, resulting in better biomineralization and improved osseointegration.


  • Open Access

    Experimental Investigations on The Effect of Tungsten Content on the Machining Behaviour of Tungsten Heavy Alloys

    by Chithajalu Kiran Sagar, Amrita Priyadarshini, Amit Kumar Gupta

    The present work attempts to assess the machinability of tungsten heavy alloys (WHAs) with varying tungsten content in terms of different machining characteristics such as chip thickness, material removal rate, cutting force and surface roughness under varied cutting conditions. The feed rate is found to have major influence on the machining characteristics; whereas the effect of rake angle appears to be marginal. With increase in W content both cutting force and material removal rate increase whereas surface roughness decreases. Since WHAs are difficult to machine, an additional objective of the study is to optimize machining parameters. An optimal balance of the experimental cutting parameters using Grey relational analysis has been achieved, which can be effectively employed for the machining of the alloys with close dimensional tolerances and desirable surface finish.


  • An Alternate Approach to SHPB Tests to Compute Johnson-Cook Material Model Constants for 97 WHA at High Strain Rates and Elevated Temperatures Using Machining Tests

    by Chithajalu Kiran Sagar, Amrita Priyadarshini, Amit Kumar Gupta, Tarun Kumar, Shreya Saxena

    With advances in computational techniques, numerical methods such as finite element method (FEM) are gaining much of the popularity for analysis as these substitute the expensive trial and error experimental techniques to a great extent. Consequently, selection of suitable material models and determination of precise material model constants are one of the prime concerns in FEM. This paper presents a methodology to determine the Johnson-Cook constitutive equation constants (JC constants) of 97 W Tungsten heavy alloys (WHAs) under high strain rate conditions using machining tests in conjunction with Oxley’s predictive model and particle swarm optimization (PSO) algorithm. Currently, availability of the high strain rate data for 97 WHA are limited and consequently, JC constants for the same are not readily available. The overall methodology includes determination of three sets of JC constants, namely, M1 and M2 from the Split-Hopkinson pressure bar (SHPB) test data available in literature by using conventional optimization technique and artificial bee colony (ABC) algorithm, respectively. However, M3 is determined from machining tests using inverse identification method. To validate the identified JC constants, machining outputs (cutting forces, temperature, and shear strain) are predicted using finite element (FE) model by considering M1, M2, and M3 as input under different cutting conditions and then validated with corresponding experimental values. The predicted outputs obtained using JC constants M3 closely matched with that of the experimental ones with error percentage well within 10%.


  • Experimental investigation of tool wear characteristics and analytical prediction of tool life using a modified tool wear rate model while machining 90 tungsten heavy alloys

    by Chithajalu Kiran Sagar, Amrita Priyadarshini, Amit Kumar Gupta, Devanshi Mathur

    Tungsten heavy alloys are widely used in the manufacturing of weights for aircraft, missiles, boats and race cars; penetrators; radiation shielding; and radioisotope containers. Manufacturing these components needs machining as a secondary operation. Since tungsten heavy alloys are difficult to machine, the in-depth analysis of tool wear growth and mechanism during machining of these alloys becomes essential. Hence, this work focuses on the experimental study of flank wear growth and its effect on other machining outputs for two different tool geometries (−5° and 2° rake angles) during turning of 90 tungsten heavy alloys. The predominant wear mechanism was identified as adhesion based on scanning electron microscopic analysis. Finally, three commonly used analytical tool wear rate models and one newly proposed model (modified Zhao model) were utilized for the prediction of flank wear growth and tool life. It was observed that the modified Zhao model could predict tool flank wear fairly well within error percentage of 4%–7% and thus could be used as a benchmark while machining difficult-to-cut alloys.


  • A review on alloy composition and synthesis of β-Titanium alloys for biomedical applications

    by Chennakesava Sai Pitchi, Amrita Priyadarshini, Ganesh Sana, Suresh Kumar Reddy Narala