ASAgata Strojny-Nędza

Agata Strojny-Nędza

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Agata Strojny-Nędza has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Oxidation and Corrosion Resistance of NiCr-Re and NiCr-Re-Al2O3 Materials Fabricated by Spark Plasma Sintering

    by Katarzyna Pietrzak, Agata Strojny-Nędza, Kamil Kaszyca, Ivan Shepa, Erika Mudra, Marek Vojtko, Jan Dusza, Vitaliy Antal, Jana Hovancova, Marcin Chmielewski

    The thermal and oxidation resistance of elements found in the combustion boilers of power generation plants are some of the most important factors deciding their effectiveness. This paper shows the experimental results of the influence of NiCr-based material composition on the microstructure and phase changes occurring during the oxidation and corrosion process. NiCr alloy was modified by the addition of rhenium and aluminum oxide. Materials were densified using the spark plasma sintering method at a sintering temperature of 1050 °C. Oxidation tests conducted up to 1100 °C under synthetic airflow revealed the formation of a thin Cr2O3 layer protecting the material against in-depth oxidation. Results of electrochemical corrosion in a 0.5 M NaCl solution indicated a positive role of Re and Al2O3 addition, confirmed by low corrosion current density values in comparison to the other reference materials. According to the provided positive preliminary test results, we can conclude that a NiCr-Re-Al2O3 system in coating form was successfully obtained by the plasma spraying method.


  • Open Access

    FGM based on copper–alumina composites for brake disc applications

    by Agata Strojny-Nędza, Katarzyna Pietrzak, Flavia Gili, Marcin Chmielewski

    Copper–alumina composites of the interpenetrating networks type are interesting materials for many applications because of their properties. On the base of preliminary investigations and practical works, in order to obtain a material with high resistance to friction wear as well as good dissipation of heat generated during work, it was decided that a developed material would be prepared on the base of the Cu–Al2O3 composite, with a graded composition. In this paper, we present the developed method of manufacturing dense copper–alumina FGMs, using ceramic preform with a graded porosity infiltrated with molten copper. The article also presents the full characterization of the obtained materials and mainly the impact of microstructure on the useful properties. The produced gradient material of a Cu–Al2O3 brake disk underwent tribological tests under conditions resembling real conditions. These disks also went through a series of abrasive wear trials at different operation stages. In comparison with the reference material (i.e., grey cast iron), the obtained gradient materials are characterized by a lower degree of wear when retaining a similar coefficient of friction value due to the ceramic phase addition. Additionally, it was found that using the copper-based gradient material guarantees faster heat dissipation from the contact area.


  • Open Access

    Development of Pore-Free Ti-Si-C MAX/Al-Si Composite Materials Manufactured by Squeeze Casting Infiltration

    by Anna Dmitruk, Krzysztof Naplocha, Andrzej Żak, Agata Strojny-Nędza, Hajo Dieringa, Karl Ulrich Kainer

    Open-porous MAX phase skeletons from Ti3SiC2 were manufactured by Microwave-Assisted Self-propagating High-temperature Synthesis (MASHS) and subsequently subjected to squeeze casting infiltration with an Al-Si lightweight casting alloy (EN AC-44200). This alloy was chosen due to its high flowability, corrosion resistance and good machinability. The manufactured composites, together with a reference sample of the original alloy, underwent testing of thermal properties, including thermal conductivity and diffusivity, specific heat and thermal expansion in the temperature range 50-500 °C, which corresponds to the expected working temperatures of the material. The fabricated AlSi/Ti3SiC2 composites have significantly increased thermal stability, with coefficients of thermal expansion (approximately 10-11 × 10−6 °C−1) half that of the original alloy. As regards mechanical properties, the instrumental Young’s modulus and Vickers hardness of the composite materials are 170.8 and 8.5 GPa, respectively. Moreover, the microstructure and phase composition, structural defects and potential impacts between constituents of the manufactured composites were characterized using SEM, TEM and STEM microscopy and EDS and XRD analysis.


  • Open Access

    Influence of Material Coating on the Heat Transfer in a Layered Cu-SiC-Cu Systems

    by A. Strojny-Nędza, K. Pietrzak, M. Teodorczyk, M. Basista, W. Węglewski, M. Chmielewski

    This paper describes the process of obtaining Cu-SiC-Cu systems by way of spark plasma sintering. A monocrystalline form of silicon carbide (6H-SiC type) was applied in the experiment. Additionally, silicon carbide samples were covered with a layer of tungsten and molybdenum using chemical vapour deposition (CVD) technique. Microstructural examinations and thermal properties measurements were performed. A special attention was put to the metal-ceramic interface. During annealing at a high temperature, copper reacts with silicon carbide. To prevent the decomposition of silicon carbide two types of coating (tungsten and molybdenum) were applied. The effect of covering SiC with the aforementioned elements on the composite’s thermal conductivity was analyzed. Results were compared with the numerical modelling of heat transfer in Cu-SiC-Cu systems. Certain possible reasons behind differences in measurements and modelling results were discussed.


  • Open Access

    The influence of electrocorundum granulation on the properties of sintered Cu/electrocorundum composites

    by A. Strojny-Nędza, K. Pietrzak, W. Węglewski

    Copper/alumina composites are extensively used in automotive and aerospace industry for products that are subjected to severe thermal and mechanical loadings, such as rocket thrusters and components of aircraft engines. These materials are well-known for their good frictional wear resistance, good resistance to thermal fatigue, high thermal conductivity and high specific heat. In this paper, the sintering process of copper/electrocorundum composites reinforced by electrocorundum particles with diameters of 3 or 180 μm and 1, 3, 5 vol.% content is presented. The effects of different particle sizes of the ceramic reinforcement on the microstructure, physical, mechanical, tribological and thermal properties of the fabricated composites are discussed.


  • Open Access

    Sintering Behavior and Mechanical Properties of NiAl, Al2O3, and NiAl-Al2O3 Composites

    by M. Chmielewski, S. Nosewicz, K. Pietrzak, J. Rojek, A. Strojny-Nędza, S. Mackiewicz, J. Dutkiewicz