Syed Humayun Basha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Syed Humayun Basha has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Xinyao Xie
4 shared publicationsZi-Xiong Guo
4 shared publications- Zi-Xiong Guo
College of Civil Engineering, Huaqiao University, Xiamen 361021, China
3 shared publications - Hai Chen
College of Harbour and Coastal Engineering, Jimei University, Xiamen 361021, China
1 shared publication - Hemant B. Kaushik
Indian Institute of Technology Guwahati
1 shared publication Hong-Song Hu
Huaqiao Univ
1 shared publication
Latest Publications
- 19 November 2026
- Published by Elsevier in Engineering Structures
- Vol. 372
Seismic performance of masonry infill walls under bidirectional loading using 3D digital image correlation measurement technique
- 19 November 2026
- Published by Elsevier in Engineering Structures
- Vol. 372
Seismic performance of masonry infill walls under bidirectional loading using 3D digital image correlation measurement technique
- Open Access
- 15 May 2026
- Published by Elsevier in Results in Engineering
- Vol. 30
Flexural load performance for 3D-printed fiber reinforced cementitious composite beams: coupling materials with design optimization
- 15 May 2026
- Published by Elsevier in Results in Engineering
- Vol. 30
Open AccessFlexural load performance for 3D-printed fiber reinforced cementitious composite beams: coupling materials with design optimization
- 10 March 2025
- Published by Elsevier in Engineering Structures
- Vol. 332
Unified tri-linear theoretical model for masonry infilled RC frames subjected to out-of-plane lateral loads
- 10 March 2025
- Published by Elsevier in Engineering Structures
- Vol. 332
Unified tri-linear theoretical model for masonry infilled RC frames subjected to out-of-plane lateral loads
- 1 November 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 34 (11) , 04022302
Effect of Structural Bonding Patterns on Mechanical Characteristics of Clay Brick Masonry under Different Loadings Using Digital Image Correlation Technique
This paper assesses the effect of two different structural bonding patterns on the mechanical characteristics of clay brick masonry assemblages under compression, flexure, and shear loading conditions. A 2D digital image correlation technique (DIC) was used to appraise the nonlinear compressive stress-strain characteristics, orthotropic properties, damage, and failure mechanisms of masonry prisms. The experimental investigation ascertained that full-brick thick masonry exhibited reasonably higher capacity and deformation characteristics than half-brick thick masonry under compression, flexure, and diagonal compression loadings, except in bed joint shear strength. The compressive strength and corresponding strain of full-brick thick Flemish bond prisms were higher and had more deformable (maximum strain recorded 2.4 times) behavior than half-brick thick masonry prisms. The failure mechanics of the masonry was quantitatively established by strain analysis obtained from DIC. The rupture modulus of Flemish bond masonry walls was four times higher, and its failure (a combination of tensile splitting of bricks and bed joint failure) was gradual compared to stack bond masonry. The diagonal compression strength of full-brick thick masonry wallettes was about 1.3 times as large as running bond wallettes, as the bond arrangement resisted diagonal cracks propagation. The applicability of the available idealized compressive stress-strain analytical models was evaluated, and a few improvements were recommended. The research study assessed that due attention needs to be given to structural bonding patterns in evaluating the mechanical characteristics of masonry required in the design and analytical modelling of masonry constructions. DIC technique can be conveniently used to capture the nonlinear strain characteristics and can be handy in detecting the damage early.
- 1 November 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 34 (11) , 04022302
Effect of Structural Bonding Patterns on Mechanical Characteristics of Clay Brick Masonry under Different Loadings Using Digital Image Correlation Technique
This paper assesses the effect of two different structural bonding patterns on the mechanical characteristics of clay brick masonry assemblages under compression, flexure, and shear loading conditions. A 2D digital image correlation technique (DIC) was used to appraise the nonlinear compressive stress-strain characteristics, orthotropic properties, damage, and failure mechanisms of masonry prisms. The experimental investigation ascertained that full-brick thick masonry exhibited reasonably higher capacity and deformation characteristics than half-brick thick masonry under compression, flexure, and diagonal compression loadings, except in bed joint shear strength. The compressive strength and corresponding strain of full-brick thick Flemish bond prisms were higher and had more deformable (maximum strain recorded 2.4 times) behavior than half-brick thick masonry prisms. The failure mechanics of the masonry was quantitatively established by strain analysis obtained from DIC. The rupture modulus of Flemish bond masonry walls was four times higher, and its failure (a combination of tensile splitting of bricks and bed joint failure) was gradual compared to stack bond masonry. The diagonal compression strength of full-brick thick masonry wallettes was about 1.3 times as large as running bond wallettes, as the bond arrangement resisted diagonal cracks propagation. The applicability of the available idealized compressive stress-strain analytical models was evaluated, and a few improvements were recommended. The research study assessed that due attention needs to be given to structural bonding patterns in evaluating the mechanical characteristics of masonry required in the design and analytical modelling of masonry constructions. DIC technique can be conveniently used to capture the nonlinear strain characteristics and can be handy in detecting the damage early.
- 25 October 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 63
Seismic behavior of RCS frame joints applied with high-strength bolts-end plate connection
- 25 October 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 63
Seismic behavior of RCS frame joints applied with high-strength bolts-end plate connection
- Open Access
A Novel Shear Strengthening of Existing RC Shear Walls Using Steel Wire Mesh and Polymer Mortar
A new type of strengthening technique for existing reinforced concrete (RC) shear walls was proposed using steel wire mesh (SWM) and polymer mortar. The experimental campaign consists of testing one conventional RC shear wall specimen and four specimens strengthened using different configurations of steel wire mesh ratios and wrapping methods under cyclic lateral loading. The experimental results showed that the application of steel wire meshes and polymer mortar not only delayed the shear cracks formation but also effectively controlled the crack propagation. The average increase in cracking load of strengthened specimens was about 79%. The lateral load-carrying capacity of the strengthened specimens increased (about 55%) with the increase in the considered steel wire mesh reinforcement ratio compared to the control specimen. Wrapping of steel wire meshes around the shear wall surface prevented debonding of polymer mortar layers, and enhanced the performance compared to wrapping only on exposed surfaces. A theoretical expression to estimate the capacity of the strengthened shear walls was proposed based on the softened strut-and-tie model. The proposed expression fairly predicted the capacity of the strengthened specimens for the present and previous study.
Open AccessA Novel Shear Strengthening of Existing RC Shear Walls Using Steel Wire Mesh and Polymer Mortar
A new type of strengthening technique for existing reinforced concrete (RC) shear walls was proposed using steel wire mesh (SWM) and polymer mortar. The experimental campaign consists of testing one conventional RC shear wall specimen and four specimens strengthened using different configurations of steel wire mesh ratios and wrapping methods under cyclic lateral loading. The experimental results showed that the application of steel wire meshes and polymer mortar not only delayed the shear cracks formation but also effectively controlled the crack propagation. The average increase in cracking load of strengthened specimens was about 79%. The lateral load-carrying capacity of the strengthened specimens increased (about 55%) with the increase in the considered steel wire mesh reinforcement ratio compared to the control specimen. Wrapping of steel wire meshes around the shear wall surface prevented debonding of polymer mortar layers, and enhanced the performance compared to wrapping only on exposed surfaces. A theoretical expression to estimate the capacity of the strengthened shear walls was proposed based on the softened strut-and-tie model. The proposed expression fairly predicted the capacity of the strengthened specimens for the present and previous study.
- 1 March 2021
- Published by Elsevier in Thin-Walled Structures
- Vol. 160
Compressive behavior of fabricated coupled composite columns under eccentric loads
- 1 March 2021
- Published by Elsevier in Thin-Walled Structures
- Vol. 160
Compressive behavior of fabricated coupled composite columns under eccentric loads
- 1 January 2015
- Published by Springer Nature
- p. 2427-2433
Non-linear Behavior of Weak Brick-Strong Mortar Masonry in Compression
- 1 January 2015
- Published by Springer Nature
- p. 2427-2433
Non-linear Behavior of Weak Brick-Strong Mortar Masonry in Compression