Thomas Heuzé
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Thomas Heuzé has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Laurent Stainier
Central Nantes, GEM, Nantes, France
8 shared publications - Jean-Michel Bergheau
Cole Centrale Lyon, CNRS, ENTPE, LTDS, UMR5513, ENISE, University Lyon, Saint-tienne, France
5 shared publications - Guillaume Racineux
Central School of Nantes, Research Institute in Civil and Mechanical Engineering, 44321 Nantes, France
4 shared publications Jean-Baptiste Leblond
4 shared publications- Adrien Renaud
MSSMat Laboratory CentraleSupélec Gif‐sur‐Yvette France
3 shared publications Benoit Lagain
3 shared publications
Latest Publications
- Open Access
- 15 September 2026
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 463
Variational formulation of the constitutive relaxation at finite rate of the mechanical state in multiphase flows with the diffuse-interface method
- 15 September 2026
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 463
Open AccessVariational formulation of the constitutive relaxation at finite rate of the mechanical state in multiphase flows with the diffuse-interface method
- Open Access
- 27 February 2026
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 332
Proof-of-concept of magnetic pulse disassembly of adhesively bonded Aluminum 2017 T4-MARS 300 specimen
- 27 February 2026
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 332
Open AccessProof-of-concept of magnetic pulse disassembly of adhesively bonded Aluminum 2017 T4-MARS 300 specimen
- Open Access
- 1 January 2026
- Published by KEAI Publishing in Defence Technology
- Vol. 55, 64-79
Magnetic pulse welding of Al-5754 with Al-7075 and MARS 380: Weldability windows and ballistic testing
- 1 January 2026
- Published by KEAI Publishing in Defence Technology
- Vol. 55, 64-79
Open AccessMagnetic pulse welding of Al-5754 with Al-7075 and MARS 380: Weldability windows and ballistic testing
- 24 September 2023
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 125 (1)
ADER discontinuous Galerkin Material Point Method
The first‐order accurate discontinuous Galerkin Material Point Method (DGMPM), initially introduced by Renaud et al. (J Comput Phys. 2018;369:80–102.), considers a solid body discretized by a collection of material points carrying the history of the matter, embedded in an arbitrary grid on which a nodal discontinuous Galerkin approximation is defined, and that serves to solve balance equations. This method has been shown to be promising, especially for solving hyperbolic problems in finite deforming solids (Renaud et al. Int J Numer Methods Eng. 2020;121(4):664–689. Renaud et al. Comput Methods Appl Mech Eng. 2020;365:112987.). The main goal of this research is to extend the first‐order DGMPM to arbitrary high‐order accurate approximations. This is performed by adapting the ADER (Arbitrary high order DErivative Riemann problem) approach (Busto et al. Front Phys. 2020;8:32.) to the particular spatial discretization of the DGMPM. First, the predictor step permits to design a particle‐to‐grid projection of arbitrary high order of accuracy, consistent with that of the nodal discontinuous Galerkin approximation defined on the arbitrary grid. This is performed using a moving least square approximation for the ADER predictor field. Second, since the degrees of freedom of the predictor field are now defined at material points, the computation of the constitutive response of the material is ensured to be always performed at these material points. This is of crucial importance for history‐dependent constitutive models because it avoids any diffusive transfer of internal variables on a new computational grid. Finally, a total Lagrangian formulation of equations is kept, which allows to precompute once and for all both the nodal discontinuous Galerkin approximation and that of the ADER predictor field, until the arbitrary grid is discarded if required. The method is illustrated on a few two‐dimensional numerical examples, on which comparisons are shown with the ADER‐DGFEM and Runge–Kutta‐DGFEM.
- 24 September 2023
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 125 (1)
ADER discontinuous Galerkin Material Point Method
The first‐order accurate discontinuous Galerkin Material Point Method (DGMPM), initially introduced by Renaud et al. (J Comput Phys. 2018;369:80–102.), considers a solid body discretized by a collection of material points carrying the history of the matter, embedded in an arbitrary grid on which a nodal discontinuous Galerkin approximation is defined, and that serves to solve balance equations. This method has been shown to be promising, especially for solving hyperbolic problems in finite deforming solids (Renaud et al. Int J Numer Methods Eng. 2020;121(4):664–689. Renaud et al. Comput Methods Appl Mech Eng. 2020;365:112987.). The main goal of this research is to extend the first‐order DGMPM to arbitrary high‐order accurate approximations. This is performed by adapting the ADER (Arbitrary high order DErivative Riemann problem) approach (Busto et al. Front Phys. 2020;8:32.) to the particular spatial discretization of the DGMPM. First, the predictor step permits to design a particle‐to‐grid projection of arbitrary high order of accuracy, consistent with that of the nodal discontinuous Galerkin approximation defined on the arbitrary grid. This is performed using a moving least square approximation for the ADER predictor field. Second, since the degrees of freedom of the predictor field are now defined at material points, the computation of the constitutive response of the material is ensured to be always performed at these material points. This is of crucial importance for history‐dependent constitutive models because it avoids any diffusive transfer of internal variables on a new computational grid. Finally, a total Lagrangian formulation of equations is kept, which allows to precompute once and for all both the nodal discontinuous Galerkin approximation and that of the ADER predictor field, until the arbitrary grid is discarded if required. The method is illustrated on a few two‐dimensional numerical examples, on which comparisons are shown with the ADER‐DGFEM and Runge–Kutta‐DGFEM.
- Open Access
Electrohydraulic Crimping of Tubes within Rings
Crimping processes are commonly used in industry to join two tubular parts together. In the case of positive clearance crimping, one of the two parts must be plastically deformed to fill the initial clearance and block elastic deformations in the second one. The strength of the assembly will then depends on the residual contact pressure established at the interface. Quasi-static processes are the most commonly used to perform these operations, but over the past two decades, there has been a growing interest in the use of dynamic crimping by magnetic pulse. Processes that generate high-strain rate allow to reduce the springback, which is of great interest for crimping. However, its use is limited if the part to be deformed is made of a poor electrical conductor material or if its dimensions are too small. This paper presents an alternative for dynamically crimping tubes within rings using electrohydraulic process. An experimental equipment has been designed to guide and amplify pressure waves to the area to be deformed. Two amplifiers called acoustic and mechanical pulse shapers (APS and MPS) have been tested and allow to reach hoop strain rate at about 1000 and 100 s respectively. An analytical model was also built allowing to define the stored energy and the inter-electrodes distance to maximize the pressure. Results of push-out tests are also presented and demonstrate the ability of the electrohydraulic crimping process coupled with the MPS to crimp small 316L tubes into rings made of the same material, but achieving crimping successfully with the APS still require further work.Open AccessElectrohydraulic Crimping of Tubes within Rings
Crimping processes are commonly used in industry to join two tubular parts together. In the case of positive clearance crimping, one of the two parts must be plastically deformed to fill the initial clearance and block elastic deformations in the second one. The strength of the assembly will then depends on the residual contact pressure established at the interface. Quasi-static processes are the most commonly used to perform these operations, but over the past two decades, there has been a growing interest in the use of dynamic crimping by magnetic pulse. Processes that generate high-strain rate allow to reduce the springback, which is of great interest for crimping. However, its use is limited if the part to be deformed is made of a poor electrical conductor material or if its dimensions are too small. This paper presents an alternative for dynamically crimping tubes within rings using electrohydraulic process. An experimental equipment has been designed to guide and amplify pressure waves to the area to be deformed. Two amplifiers called acoustic and mechanical pulse shapers (APS and MPS) have been tested and allow to reach hoop strain rate at about 1000 and 100 s respectively. An analytical model was also built allowing to define the stored energy and the inter-electrodes distance to maximize the pressure. Results of push-out tests are also presented and demonstrate the ability of the electrohydraulic crimping process coupled with the MPS to crimp small 316L tubes into rings made of the same material, but achieving crimping successfully with the APS still require further work. - 30 October 2020
- Published by Springer Nature in Continuum Mechanics and Thermodynamics
- Vol. 33 (2) , 563-589
Multifield variational formulations of diffusion initial boundary value problems
- 30 October 2020
- Published by Springer Nature in Continuum Mechanics and Thermodynamics
- Vol. 33 (2) , 563-589
Multifield variational formulations of diffusion initial boundary value problems
- 1 September 2020
- Published by Elsevier in Finite Elements in Analysis and Design
- Vol. 176
Remapping-free variational h-adaption for strongly coupled thermo-mechanical problems
- 1 September 2020
- Published by Elsevier in Finite Elements in Analysis and Design
- Vol. 176
Remapping-free variational h-adaption for strongly coupled thermo-mechanical problems