Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Guillaume Racineux has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Magnetic pulse welding of Al-5754 with Al-7075 and MARS 380: Weldability windows and ballistic testing

    by Benoit Lagain, Thomas Heuzé, Guillaume Racineux, Michel Arrigoni


  • miniBLAST: A Novel Experimental Setup for Laboratory Testing of Structures Under Blast Loads

    by A. Morsel, F. Masi, E. Marché, G. Racineux, P. Kotronis, I. Stefanou


  • Open Access

    Experimental Methodology to Identify Optimal Friction Stir Welding Parameters Based on Temperature Measurement

    by Moura Abboud, Laurent Dubourg, Guillaume Racineux, Olivier Kerbrat

    Friction stir welding (FSW) is a widely employed welding process, in which advancing and rotational speeds consitute critical parameters shaping the welding outcome and affecting the temperature evolution. This work develops an experimental methodology to identify optimal FSW parameters based on real-time temperature measurement via a thermocouple integrated within the tool. Different rotational and welding speeds were tested on AA5083-H111 and AA6082-T6. Our results underscore the importance of attaining a minimum temperature threshold, specifically 0.65 times the solidus temperature, to ensure high-quality welds are reached. The latter are defined by combining temperature measurements with joint quality information obtained from cross-sectional views. Our research contributes to advancing the efficiency and effectiveness of friction stir welding in industrial settings. Furthermore, our findings suggest broad implications for the manufacturing industry, offering practical insights for enhancing weld quality and process optimization.


  • Open Access

    Electrohydraulic Crimping of Tubes within Rings

    by Ronan Le Mentec, Cheick Tidiane Sow, Thomas Heuzé, Patrick Rozycki, Guillaume Racineux

    Crimping processes are commonly used in industry to join two tubular parts together. In the case of positive clearance crimping, one of the two parts must be plastically deformed to fill the initial clearance and block elastic deformations in the second one. The strength of the assembly will then depends on the residual contact pressure established at the interface. Quasi-static processes are the most commonly used to perform these operations, but over the past two decades, there has been a growing interest in the use of dynamic crimping by magnetic pulse. Processes that generate high-strain rate allow to reduce the springback, which is of great interest for crimping. However, its use is limited if the part to be deformed is made of a poor electrical conductor material or if its dimensions are too small. This paper presents an alternative for dynamically crimping tubes within rings using electrohydraulic process. An experimental equipment has been designed to guide and amplify pressure waves to the area to be deformed. Two amplifiers called acoustic and mechanical pulse shapers (APS and MPS) have been tested and allow to reach hoop strain rate at about 1000 and 100 s−1 respectively. An analytical model was also built allowing to define the stored energy and the inter-electrodes distance to maximize the pressure. Results of push-out tests are also presented and demonstrate the ability of the electrohydraulic crimping process coupled with the MPS to crimp small 316L tubes into rings made of the same material, but achieving crimping successfully with the APS still require further work.


  • Friction Stir Welding Operating Window for Aluminum Alloy Obtained by Temperature Measurement

    by Moura Abboud, Laurent Dubourg, Adrien Leygue, Guillaume Racineux, Olivier Kerbrat


  • Open Access

    Improved Coil Design for Magnetic Pulse Welding of Metallic Sheets

    by Rishabh Shotri, Koen Faes, Guillaume Racineux, Amitava De

    Magnetic pulse welding of overlapping dissimilar metallic sheets is an emerging technique and usually employs flat electromagnetic coils with rectangular-, H-, I-, and E-shaped cross-sections. The asymmetric cross-section of these coils results in a non-uniform electromagnetic field and in a non-uniform connection in the interface between the overlapping sheets. In this article, the use of a novel O-shaped flat coil is proposed to join an aluminium flyer sheet with a target steel sheet. A finite element-based numerical model is developed to calculate the electromagnetic field, flyer velocity, and its gradual impact onto the target, and the deformations of the sheet assembly. The calculated results with the O-shaped coil show a high-intensity electromagnetic field, the concentration of which decreases radially outwards in a uniform manner. The numerically computed and experimentally measured flyer velocity are found to be in fair agreement. The calculated results show a regularly decreasing impact behaviour between the flyer and target and their resulting deformation. The measured results show the formation of an annular ring-shaped joint profile that is generally found to be stronger compared to that obtained with flat coils with a rectangular cross-section.


  • Open Access

    Analytical Estimation of Electromagnetic Pressure, Flyer Impact Velocity, and Welded Joint Length in Magnetic Pulse Welding

    by Rishabh Shotri, Koen Faes, Guillaume Racineux, Amitava De

    Magnetic pulse welding involves the joining of two metallic parts in a solid state by the use of a short and intense electromagnetic impulses and the resulting impact between the parts. The coalesced interface undergoes visco-plastic deformation at a high strain rate and exhibits a wavy shape at a microscopic scale. A practical estimation of the electromagnetic pressure, impact velocity and welded joint length as a function of the process conditions and the electromagnetic coil geometry is required but currently not available. Three novel analytical relations for the estimation of the electromagnetic pressure, impact velocity, and welded joint length for magnetic pulse welding of tubes and sheets, are presented. These relations were developed systematically, following a dimensional analysis, and validated for a wide range of conditions from independent literature. The comparison of the analytically computed results and the corresponding values reported in the literature has illustrated that the proposed analytical relations can be used for the estimation of the electromagnetic pressure and impact velocity for the magnetic pulse welding of tubes and sheets with a good level of confidence. The analytically calculated results for the welded joint length show a little discrepancy with the corresponding experimentally measured values. Further investigations and more experimentally measured results are required to arrive at a more comprehensive analytical relation for the prediction of welded joint length.


  • Open Access

    Magnetic Pulse Hybrid Joining of Polymer Composites to Metals

    by Chady Khalil, Surendar Marya, Guillaume Racineux

    To lighten their vehicles, car manufacturers are inclined to substitute steel structures with aluminum alloys or composites parts. They are then faced with the constraints inherent to dissimilar (galvanized steel/aluminum) or hybrid (metal/composite) assemblies. Recent developments in magnetic pulse welding seems to offer a viable route. Very fast, this process can be robotized and generates a very localized heating system which limits the formation of intermetallic and damage the composite. Low energy consumption, without filler metal or smoke it is recognized as an environmentally friendly process. In this paper, electromagnetic pulse welding is exploited to assemble polymer composite to metals. Two techniques, a metallic insert in polymer composite or an external patch, have been tested with possible design considerations.


  • Open Access

    Magnetic Pulse Welding and Spot Welding with Improved Coil Efficiency—Application for Dissimilar Welding of Automotive Metal Alloys

    by Chady Khalil, Surendar Marya, Guillaume Racineux

    Lightweight structures in the automotive and transportation industry are increasingly researched. Multiple materials with tailored properties are integrated into structures via a large spectrum of joining techniques. Welding is a viable solution in mass scale production in an automotive sector still dominated by steels, although hybrid structures involving other materials like aluminum are becoming increasingly important. The welding of dissimilar metals is difficult if not impossible, due to their differential thermo mechanical properties along with the formation of intermetallic compounds, particularly when fusion welding is envisioned. Solid-state welding, as with magnetic pulse welding, is of particular interest due to its short processing cycles. However, electromagnetic pulse welding is constrained by the selection of processing parameters, particularly the coil design and its life cycle. This paper investigates two inductor designs, a linear (I) and O shape, for the joining of sheet metals involving aluminum and steels. The O shape inductor is found to be more efficient both with magnetic pulse (MPW) and magnetic pulse spot welding (MPSW) and offers a better life cycle. Both simulation and experimental mechanical tests are presented to support the effect of inductor design on the process performance.