EHE. Haro

E. Haro

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


E. Haro has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Hot Spot Temperature in an HTS Coil: Simulations With MIITs and Finite Element Method

    by E. Haro, A. Stenvall, J. van Nugteren, G. Kirby

    MIITs, a zero-dimensional concept to study hot spot temperature, has been previously used to estimate hot spot temperatures and quench heater delays in NbTi and Nb 3 Sn magnets. However, quench behavior is completely different in high-temperature superconducting (HTS) magnets due to the slow normal zone propagation velocity and the high temperature margin. Because the MIITs concept does not take into account thermal diffusion in the magnet, opposite to the finite-element method (FEM) analysis, the difference of these concepts is studied in this paper. Here, we have taken the approach to compute the hot spot temperatures for a future HTS magnet, designed to be built from REBCO Roebel cable, with MIITs and FEM simulations. The magnet protection is accomplished with a dump resistor, and the effect of quench detection threshold voltage on the hot spot temperature has been studied. Furthermore, the inductance of the magnet increases with the magnet length. Thus, there exists a maximum inductance of the magnet, which should not be exceeded to be able to protect the magnet only with a dump resistor. The hot spot temperatures with different values of inductance are also studied in this paper. Our simulations show that the hot spot temperatures computed with MIITs are from 60 to 150 K higher than those of FEM analysis. Thus, the MIITs concept seems unreliable when considering hot spot temperatures in HTS magnets protected with only dump resistors. However, the MIITs concept might be a usable tool when comparing different magnet designs. If 400 K is the upper limit for the hot spot temperature and the protection scheme includes only a dump resistor, the length of the investigated magnet can be increased to only such value that the magnet inductance is at most 50 mH.


  • Reducing Modeling Domain to Speed-Up Quench Simulations of HTS Coils

    by E. Haro, A. Stenvall

    Three-dimensional quench analyses of large magnet systems, such as low- and high-temperature superconductor hybrids for particle accelerators of future, are computationally very heavy when cable level details are taken into account. Mesh based modelling methods, like finite-element method, will result in a large amount of elements and consequently degrees of freedom in these simulations. In this paper we simulate the quench using mesh structures including cable and insulation layers in some parts of the coil system. Elsewhere we consider the coil as a homogenous mixture of cable and insulation. Futhermore, in some simulations we completely neglect parts of the magnet system. Then we study how these modelling decisions affect the simulated hot spot temperature rise and development of resistive voltage. Using this kind of geometry adaptation in an appropriate way we can considerably shorten simulations without losing reliability of the results. In this paper we compare how modeling decisions related to representing the magnet in a modelling software affect the important quench parameters and computation time. Examples are computed with an in-house programmed quench software for a 6T HTS insert designed within the EuCARD project.


  • Quench Considerations and Protection Scheme of a High Field HTS Dipole Insert Coil

    by E. Haro, A. Stenvall, T. Lecrevisse, J. Fleiter, J. M. Rey, M. Sorbi, M. Devaux, C. Trophime, P. Fazilleau, G. Volpini, et al.

    The large scale particle accelerators of the future in the 20 T regime are enabled by high temperature superconducting magnets. The dipole magnets needed in new high-field accelerators can be constructed with an YBCO insert and a Nb3Sn outsert. Such a configuration makes the quench analysis and magnet protection challenging because the quench behavior in both of these coils is different and there is very strong inductive coupling between the coils. The Nb3Sn coil is characterized by high energy and current and relatively fast quench propagation velocity. However, quench propagates slowly in YBCO coils because of typically wide spread large temperature margin. Currently, in the EuCARD project, a European collaboration is targeting to construct a small-scale high field YBCO-Nb3Sn hybrid magnet. In this paper, we scrutinize quench in the YBCO insert. We utilized an approach based on a solution of the heat diffusion equation with the finite element method. Additionally, we present a protection scheme for the coil.