Babur Ozcelik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Babur Ozcelik has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
Emel Kuram
Department of Mechanical Engineering, Gebze Technical University, Kocaeli, Turkey
5 shared publications- Faruk Yilmaz
Department of Chemistry, Gebze Technical University, Gebze, Kocaeli, Turkey
2 shared publications Ibrahim Hamarat
Department of Mechanical Engineering, Gebze Technical University, Kocaeli, Turkey
1 shared publication
Latest Publications
- 4 July 2017
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 232 (4) , 449-458
Investigation the mechanical, rheological, and morphological properties of acrylonitrile butadiene styrene blends with different recycling number content
In this study, acrylonitrile butadiene styrene polymer was exposed to 12 injection cycles to investigate the influence of recycling number on the mechanical, rheological, and morphological properties. Also, binary and ternary blends including different weight percentages and recycling number of virgin–recycled polymers were prepared. A slight decrement was found in the tensile strength values with recycling number. All blends including recycled polymer (binary or ternary) gave lower tensile strength values with respect to 100% virgin polymer. Strain at break value was decreased after twelve times recycling; however, no clear tendency was observed with the presence of different ratios of virgin polymer to recycled polymer. Impact strength of the polymer decreased with recycling number. There was relatively large drop in the third recycling, from 72 kJ/m2 to 38.5 kJ/m2; however, further recycling induced in a slower drop in the impact strength to 32.5 kJ/m2. All blends including recycled material gave lower impact strength values as compared to 100% virgin polymer. It was observed that the melt flow index values increased with the recycling number, a total of 26.53% after twelve times recycling. All blends containing recycled material showed higher melt flow index values as compared to 100% virgin polymer.
- 4 July 2017
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 232 (4) , 449-458
Investigation the mechanical, rheological, and morphological properties of acrylonitrile butadiene styrene blends with different recycling number content
In this study, acrylonitrile butadiene styrene polymer was exposed to 12 injection cycles to investigate the influence of recycling number on the mechanical, rheological, and morphological properties. Also, binary and ternary blends including different weight percentages and recycling number of virgin–recycled polymers were prepared. A slight decrement was found in the tensile strength values with recycling number. All blends including recycled polymer (binary or ternary) gave lower tensile strength values with respect to 100% virgin polymer. Strain at break value was decreased after twelve times recycling; however, no clear tendency was observed with the presence of different ratios of virgin polymer to recycled polymer. Impact strength of the polymer decreased with recycling number. There was relatively large drop in the third recycling, from 72 kJ/m2 to 38.5 kJ/m2; however, further recycling induced in a slower drop in the impact strength to 32.5 kJ/m2. All blends including recycled material gave lower impact strength values as compared to 100% virgin polymer. It was observed that the melt flow index values increased with the recycling number, a total of 26.53% after twelve times recycling. All blends containing recycled material showed higher melt flow index values as compared to 100% virgin polymer.
- 8 August 2016
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 231 (2) , 228-242
Optimization of machining parameters during micro-milling of Ti6Al4V titanium alloy and Inconel 718 materials using Taguchi method
This study focused on the optimization of micro-milling parameters for two extensively used aerospace materials (titanium and nickel-based superalloy). The experiments were planned using Taguchi experimental design method, and the influences of spindle speed, feed rate and depth of cut on machining outputs, namely, tool wear, surface roughness and cutting forces, were determined. Tool wear, surface roughness and cutting forces measured in micro-milling of Ti6Al4V titanium alloy and Inconel 718 workpiece materials were optimized by employing Taguchi’s signal-to-noise ratio. The percentage contribution of micro-milling parameters, namely, spindle speed, feed rate and depth of cut, on tool wear, surface roughness and cutting forces was indicated by analysis of variance. The regression models identifying the relationship between the input variables and the output responses were also fitted using experimental data to predict output responses without conducting the experiments. Efficiency of regression models was determined using correlation coefficients, and the predicted values were compared with experimental results. From results, it was concluded that the established regression models could be employed for predicting tool wear, surface roughness and cutting forces in micro-milling of Ti6Al4V titanium alloy and Inconel 718 workpiece materials.
- 8 August 2016
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 231 (2) , 228-242
Optimization of machining parameters during micro-milling of Ti6Al4V titanium alloy and Inconel 718 materials using Taguchi method
This study focused on the optimization of micro-milling parameters for two extensively used aerospace materials (titanium and nickel-based superalloy). The experiments were planned using Taguchi experimental design method, and the influences of spindle speed, feed rate and depth of cut on machining outputs, namely, tool wear, surface roughness and cutting forces, were determined. Tool wear, surface roughness and cutting forces measured in micro-milling of Ti6Al4V titanium alloy and Inconel 718 workpiece materials were optimized by employing Taguchi’s signal-to-noise ratio. The percentage contribution of micro-milling parameters, namely, spindle speed, feed rate and depth of cut, on tool wear, surface roughness and cutting forces was indicated by analysis of variance. The regression models identifying the relationship between the input variables and the output responses were also fitted using experimental data to predict output responses without conducting the experiments. Efficiency of regression models was determined using correlation coefficients, and the predicted values were compared with experimental results. From results, it was concluded that the established regression models could be employed for predicting tool wear, surface roughness and cutting forces in micro-milling of Ti6Al4V titanium alloy and Inconel 718 workpiece materials.
- 4 August 2016
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 29 (10) , 1443-1457
The influence of recycling number on the mechanical, chemical, thermal and rheological properties of poly(butylene terephthalate)/polycarbonate binary blend and glass-fibre-reinforced composite
Poly(butylene terephthalate)/polycarbonate (PBT/PC) binary blend was reprocessed by repeated injection moulding process to explore whether recycling is possible for this polymer blend. In the current study, PBT/PC blends were reprocessed until five processing cycles and the mechanical, chemical, thermal, and rheological properties of recycled PBT/PC blends were evaluated after each reprocessing cycle. The recycling of the glass-fibre-reinforced PBT/PC composites was also investigated in this study. From the experimental results, it was concluded that recycled glass-fibre-reinforced PBT/PC (PBT/PC-GF) composites showed better mechanical properties in comparison to virgin PBT/PC binary blends and fifth recycled PBT/PC-GF composite could be used instead of virgin PBT/PC. It was also found that PBT/PC binary blend was a suitable material for the recycling process and this polymer blend did not suffer any significant deterioration.
- 4 August 2016
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 29 (10) , 1443-1457
The influence of recycling number on the mechanical, chemical, thermal and rheological properties of poly(butylene terephthalate)/polycarbonate binary blend and glass-fibre-reinforced composite
Poly(butylene terephthalate)/polycarbonate (PBT/PC) binary blend was reprocessed by repeated injection moulding process to explore whether recycling is possible for this polymer blend. In the current study, PBT/PC blends were reprocessed until five processing cycles and the mechanical, chemical, thermal, and rheological properties of recycled PBT/PC blends were evaluated after each reprocessing cycle. The recycling of the glass-fibre-reinforced PBT/PC composites was also investigated in this study. From the experimental results, it was concluded that recycled glass-fibre-reinforced PBT/PC (PBT/PC-GF) composites showed better mechanical properties in comparison to virgin PBT/PC binary blends and fifth recycled PBT/PC-GF composite could be used instead of virgin PBT/PC. It was also found that PBT/PC binary blend was a suitable material for the recycling process and this polymer blend did not suffer any significant deterioration.
- 2 September 2015
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 84 (1-4) , 691-703
Effects of tool paths and machining parameters on the performance in micro-milling of Ti6Al4V titanium with high-speed spindle attachment
- 2 September 2015
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 84 (1-4) , 691-703
Effects of tool paths and machining parameters on the performance in micro-milling of Ti6Al4V titanium with high-speed spindle attachment
- 17 March 2015
- Published by SAGE Publications in Journal of Elastomers & Plastics
- Vol. 48 (2) , 164-181
The effects of recycling process on thermal, chemical, rheological, and mechanical properties of PC/ABS binary and PA6/PC/ABS ternary blends
In this study, polycarbonate/acrylonitrile–butadiene–styrene (PC/ABS) and polyamide 6/PC/ABS (PA6/PC/ABS) blends were reprocessed (recycled) five times and the influences of multiple molding processes on the thermal, chemical, morphological, rheological, and mechanical properties of the recycled and virgin specimens were investigated. The impact strength, tensile properties (elastic modulus, strength, and strain at break), and flexural properties (modulus and strength) were measured to determine the mechanical properties of the blends. The rheology of the samples was evaluated via measuring the melt flow index (MFI). It was concluded that the chemical structures, melting temperatures, and thermal properties of both blends did not significantly change with recycling. From the mechanical tests, in general, it was found that increasing the number of recycling processes did not considerably alter the flexural properties and tensile strength of PC/ABS blends, but decreased their MFI and impact strength. On the other hand, the elastic modulus and tensile strength of PA6/PC/ABS decreased with the number of recycling processes, whereas MFI, flexural properties, and impact strength of the ternary blends improved.
- 17 March 2015
- Published by SAGE Publications in Journal of Elastomers & Plastics
- Vol. 48 (2) , 164-181
The effects of recycling process on thermal, chemical, rheological, and mechanical properties of PC/ABS binary and PA6/PC/ABS ternary blends
In this study, polycarbonate/acrylonitrile–butadiene–styrene (PC/ABS) and polyamide 6/PC/ABS (PA6/PC/ABS) blends were reprocessed (recycled) five times and the influences of multiple molding processes on the thermal, chemical, morphological, rheological, and mechanical properties of the recycled and virgin specimens were investigated. The impact strength, tensile properties (elastic modulus, strength, and strain at break), and flexural properties (modulus and strength) were measured to determine the mechanical properties of the blends. The rheology of the samples was evaluated via measuring the melt flow index (MFI). It was concluded that the chemical structures, melting temperatures, and thermal properties of both blends did not significantly change with recycling. From the mechanical tests, in general, it was found that increasing the number of recycling processes did not considerably alter the flexural properties and tensile strength of PC/ABS blends, but decreased their MFI and impact strength. On the other hand, the elastic modulus and tensile strength of PA6/PC/ABS decreased with the number of recycling processes, whereas MFI, flexural properties, and impact strength of the ternary blends improved.