Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Katarzyna Nowińska has a total of 66 co-authors. Here are the top co-authors by number of shared publications:

  • Zdzisław Adamczyk

    Faculty of Mining, Safety Engineering and Industrial Automation, Silesian University of Technology, ul. Akademicka 2, 44-100 Gliwice, Poland

    8 shared publications
  • Janusz Szewczenko

    Department of Biomaterials and Medical Devices Engineering, Faculty of Biomedical Engineering, Silesian University of Technology, Franklina Roosevelta 40 Street, 41-800 Zabrze, Poland

    6 shared publications
  • Jaroslaw Piatkowski

    Materials Innovation Laboratory, Faculty of Materials Science and Industrial Digitalization, Silesian University of Technology, Krasinskiego 8, 40-019 Katowice, Poland

    5 shared publications
  • Tomasz Matula

    Department of Metallurgy and Recycling, Faculty of Materials Science, Silesian University of Technology, Krasinskiego 8, 40-019 Katowice, Poland

    5 shared publications
  • Ada Orłowska

    Department of Biomaterials and Medical Device Engineering, Faculty of Biomedical Engineering, Silesian University of Technology, Roosevelta 40, 41-800 Zabrze, Poland

    4 shared publications
  • Joanna Jaworska

    Centre of Polymer and Carbon Materials, Polish Academy of Sciences, M. Curie-Skłodowskiej 34, 41-819 Zabrze, Poland

    4 shared publications

Latest Publications

  • Open Access

    Machine Learning Prediction of Porosity in Low-Pressure-Cast AlSi7Mg Alloy with Varying Recycled Aluminum Content

    by Jaroslaw Piatkowski, Grzegorz Siwiec, Tomasz Matula, Beata Oleksiak, Karel Gryc, Andrzej Grabowski, Katarzyna Nowinska

    Industrial AlSi7Mg produced by low-pressure casting was evaluated with 50–95 wt.% recycled material under two conditions: no intentional Mn correction and Mn correction targeted at Mn/Fe ≈ 0.5. The porosity dataset contained 200 observations; for 60–95 wt.% recycled material, 160 records from 16 experimental conditions also included sample-specific chemical composition. Without Mn correction, MeanPor rose from 0.160% to 6.111%, whereas Mn correction reduced porosity under most conditions. Eight hypothesis-driven candidate feature architectures and 13 model families were assessed by grouped Leave-One-Scrap-Level-Out cross-validation, with hyperparameters tuned only on training data. A second-order regression with predefined interactions using recycled material content, Mn-correction variant, and sample-specific Fe gave the lowest out-of-fold (OOF) error for MeanPor (coefficient of determination (R2) = 0.9910, root mean square error (RMSE) = 0.1691, mean absolute error (MAE) = 0.1508). The reduced Sludge Factor descriptor, SFCr0 = (1 × %Fe) + (2 × %Mn), also improved prediction and reached R2 ≈ 0.986. SHAP (SHapley Additive exPlanations) was used to describe model attribution without causal interpretation. At 90 and 95 wt.% recycled material, Mn correction coincided with higher V values and more regular pore cross-sections. Sample-specific chemistry improved porosity prediction within the investigated process window; independent validation is required before use outside that range.

  • Open Access

    Structure–Barrier–Release Relationships of Low-Temperature ALD ZrO2 Thin Films on Co–Cr Alloys: Reducing Long-Term Co and Cr Ion Release in Artificial Saliva

    by Anna ZięBowicz, Wiktoria Groelich, Anita Kajzer, Wojciech Kajzer, Marta Kiel-Jamrozik, Julia Kolasa, Julia Lisoń-Kubica, Katarzyna Nowińska, Ada Orłowska, Zbigniew Paszenda, et al.

    Co–Cr alloys are widely used in biomedical devices owing to their excellent mechanical properties and corrosion resistance; however, sustained metal-ion release in physiological environments remains an important materials concern. Low-temperature atomic layer deposition (ALD) enables the formation of conformal ceramic barriers that can restrict long-term metal-ion transport. In this study, nominally ~50 nm ALD-derived ZrO2 coatings were deposited on Co–Cr substrates manufactured by investment casting (CAST), CAD/CAM milling (MILLED), and laser powder bed fusion (PRINTED). The coatings were characterized using scanning electron microscopy (SEM), atomic force microscopy (AFM), Raman spectroscopy, transmission electron microscopy with selected-area electron diffraction (TEM/SAED), and X-ray photoelectron spectroscopy (XPS), while the electrochemical response was evaluated by open-circuit potential (OCP) and electrochemical impedance spectroscopy (EIS). Long-term barrier performance was quantified by inductively coupled plasma atomic emission spectroscopy (ICP-AES) as cumulative Co and Cr release for all manufacturing routes and Mo release for the Mo-containing CAST and PRINTED alloys after 28 days in artificial saliva at 37 °C. ZrO2 deposition reduced cumulative Co and Cr release for all manufacturing routes. Mo release was also reduced in the Mo-containing alloys, with Mo remaining below the analytical detection limit (−2) for the PRINTED + ZrO2 system. Electrochemical measurements further demonstrated manufacturing-route-dependent differences in barrier response between the initial and 28-day exposure states. Overall, the findings establish a structure–barrier–release framework linking coating formation and electrochemical response with cumulative ion release, and identify 28-day cumulative ion release as a practical functional descriptor for comparing the long-term performance of ALD-derived ceramic barriers on Co–Cr alloys.

  • Open Access

    Metallurgical Waste Landfills as Potential Anthropogenic Deposits

    by Katarzyna Nowińska, Aleksandra Czajkowska, Jarosław Sikorski

    Metallurgical slags produced in the zinc–lead, copper, iron and steel metallurgical industries are characterized by a variety of technical parameters and varying chemical and mineral compositions, which depend on the type of raw material and the technological process selected and its workflow. These slags are characterized by a high content of valuable elements, including Cu, Pb, Zn, and Fe, which form complex multiphase conglomerates. In the chemical composition of Zn-Pb smelting slags, the contents of the dominant elements, i.e., Fe, Zn, and Pb, range from a few to several dozen %. These elements occur mainly in the form of polyphase oxides and silicates. The chemical composition of Cu smelting slag contains up to a few % Cu and up to several dozen % Fe, with these elements mainly forming silicates and sulphides. Iron and steel metallurgy slag contains up to several dozen % Fe, which occurs mainly in the form of silicates, oxides, and spinels. Due to their phase composition, metallurgical slags stored in landfills can have a negative impact on the environment. The phase composition of slags is one of the main factors determining their behavior in a weathering environment, i.e., their ability to release metals when exposed to atmospheric factors such as precipitation or temperature. On the other hand, such high concentrations of elements in metallurgical slags mean that they become anthropogenic deposits, and the phase composition of the slags determines how the deposited slags are processed. The aim of this article is to present the mineralogical and chemical characteristics of Zn, Pb, Cu and steel metallurgical slags deposited in landfills, along with an assessment of these materials as a source of secondary raw materials.

  • Open Access

    The Influence of SiC and Al2O3 Particles on the Microstructure and Tribological Properties of the EN-GJL-150 Cast Iron-Based Composite

    by Jaroslaw Piatkowski, Mateusz Wojciechowski, Tomasz Matula, Katarzyna Nowinska

    This article presents preliminary research on the development of a cast iron–ceramic composite for modern braking systems, such as brake discs. The composite matrix is gray cast iron with flake graphite (EN-GJL-150). The reinforcing phase is a porous ceramic composed of SiC and Al2O3 particles introduced separately (10% each) and together (70% SiC + 30% Al2O3). These particles were applied as a suspension onto polyurethane foam, yielding a ceramic structure with a pore density of up to 10 ppi. The resulting insert was placed in a mold cavity, and cast iron was poured into it. The resulting samples were treated as brake disc material, with a pad made of the commercial friction material P50094 serving as the countersample. Tribological tests showed that the lowest sample wear (average 2.23 mg/5000 m) was achieved for the composite reinforced with SiC + Al2O3 particles. This is probably due to the synergy between the antifriction properties of these particles and the lower friction coefficient (µ = 0.180–0.22). Similar mass loss values and the smallest difference between the tested samples were observed for composites with SiC particles (3.01 mg/5000 m) and Al2O3 (3.30 mg/5000 m). The second part consisted of microstructural studies. Microstructural analysis of the EN-GJL-150 + SiC + Al2O3 composite revealed a previously unobserved nucleation phenomenon at the cast iron–ceramic interface. This confirmed the general assumptions of Riposan’s theory regarding the involvement of oxide microinclusions and complex manganese sulfides of the (Mn, X)S type in the nucleation and crystallization of graphite precipitates. It was also found that, in the case of “in situ” GJL-150 + SiC + Al2O3 composites, this theory should account for the beneficial role of ceramic particles in promoting the uniform distribution of type A graphite flakes, which nucleate on their surfaces in the transition zone. Thus, the nucleating role of oxide microinclusions (the first stage of Riposan’s theory) could be taken over by SiC and Al2O3 particles, constituting a substrate for the heterogeneous nucleation of (Mn, X)S sulfides.

  • Open Access

    Optimization of Hybrid PEO/P(L/G/TMC) Coatings on WE43B Magnesium Alloy: Effect of Polymer Layer Number on Surface Properties

    by Barbara Rynkus, Ada Orłowska, Karolina Wilk, Joanna Jaworska, Katarzyna Nowińska, Karolina Szawiraacz, Justyna WięCek-Chmielarz, Krzysztof Lukaszkowicz, Mariusz Sandomierski, Piotr Kałużyński, et al.

    Magnesium alloys are promising materials for orthopedic applications due to their biodegradability and mechanical properties compatible with bone. However, their rapid degradation in physiological environments limits clinical use. In this study, WE43B magnesium alloy was coated with a PEO layer followed by a P(L/G/TMC) polymer applied via ultrasonic spraying. The influence of polymer layer number (10, 20, 30) on coating properties was systematically investigated. Scanning electron microscopy (SEM) analysis revealed an approximately fourfold reduction in porosity after polymer deposition, with progressive pore filling at higher layer numbers, while Fourier transform infrared spectroscopy (FT-IR) mapping indicated uniform polymer coverage. Compared to PEO alone, polymer-modified samples exhibited an approximately 7-fold increase in water contact angle, a ~50% reduction in surface roughness, and improved adhesion. Degradation-related analyses, including ion release, post-immersion SEM, and scanning acoustic microscopy (SAM), indicated that increasing polymer thickness effectively limited degradation processes. Ion release decreased by ~40–50% for the 30-layer coating compared to PEO, with the most pronounced reduction observed between the uncoated PEO and polymer-modified samples. These results demonstrate that the number of polymer layers plays a key role in controlling the barrier properties and stability of hybrid PEO/polymer coatings under simulated physiological conditions.

  • Open Access

    What Is the Main Cause of Shrinkage Porosity in AlSi7Mg0.6 Alloy Castings Obtained with an Increased Share of Secondary Materials?

    by Jaroslaw Piatkowski, Katarzyna Nowinska, Tomasz Matula, Andrzej Nowrot

    Determining the causes of shrinkage porosity in Al-Si-Mg alloy castings with an increased proportion of secondary materials is very important and poses many problems. The reason for this is the existence of two opposing theories. One assumes that plate-like α-Al5FeSi (β-Fe) phase segregations cause shrinkage porosity. At the same time, the other believes that thin, double-layered oxide films with air-filled voids are responsible for the porosity. To address this question, the popular commercial alloy AlSi7Mg0.6 (EN AC-42200) was selected for testing. This alloy was cast into three series: with increasing content from 0.3 to 0.8 wt.% Fe and a constant content of approx. 0.1 wt.% Mn, the second with increasing iron and manganese contents (Mn/Fe = 1/2) (both series cast by gravity), and the third series under low pressure (approx. 0.15 MPa) with increasing content from 0.8 wt.% to 1.3 wt.% Fe and a constant content of approx. 0.1 wt.% Mn. Based on DTA (Derivative Thermal Analysis) and DSC (Differential Scanning Calorimetry) tests, the order of crystallizing components in various Mn/Fe combinations was determined. It has been found that the most unfavorable phases in gravity castings are the primary crystallizing β-Al5FeSi (β-Fe) phases (over 0.7 wt.% Fe), which are the leading cause of shrinkage porosity. After adding manganese to the alloy, thermal tests indicate that after the formation of α(Al) dendrites but before the eutectic α(Al) + β(Si), the Al15(Fe,Mn)3Si2 phase crystallizes. In die-cast samples, plate-like α-Al5FeSi (β-Fe) phase precipitates were also observed, but their share is small, and their average length does not exceed 20–30 µm. However, microstructural tests revealed the presence of rare oxides. It can therefore be assumed that in the AlSi7Mg0.6 alloy cast under pressure, the primary source of shrinkage porosity is not plate-like α-Al5FeSi (β-Fe) phase precipitates, but double-layer oxide films. In all cases, it was found that the Mg2Si phase formed at the end of crystallization does not affect shrinkage porosity.


  • Open Access

    A New, Quick Method for Testing Organic Soils Based on the Electrical Impedance Spectrum of the Measuring Coil

    by Barbara Solecka, Andrzej Nowrot, Katarzyna Nowińska, Jarosław Sikorski, Adam Michczyński

    This paper presents a new, quick method for testing the content of magnetic forms of iron in organic soils. These forms are an important marker of changes occurring in the environment. This method is based on impedance spectroscopy of a measuring coil inside which the tested material is placed—the material serves as the core of the coil. Unlike EIS (electrochemical impedance spectroscopy), the new method does not use electrodes, is sensitive to magnetic forms of iron, and is non-contact (the measuring current does not flow through the tested material). The results of research on three materials, including brown peat and silt with plant detritus, are presented in this paper. The results showed that changes in the standardized components of the measuring coil impedance in the frequency range of 100–135 kHz enable the determination of the content of ferromagnetic iron oxide (Fe3O4). The proposed method is very sensitive to soil oxide content in the range of 0% to 8%. Additionally, elemental composition analysis was performed using ICP-AES (inductively coupled plasma–atomic emission spectroscopy), which allowed for comparison of iron and other metal content with impedance measurement results. The final results confirm the usefulness of impedance spectroscopy as a non-destructive method for studying sedimentary environments and assessing their mineral properties.


  • Open Access

    Modeling an Industrial Distribution Network with Significant Photovoltaic Integration Using ATP-EMTP

    by Katarzyna Nowińska, Krzysztof Kuliński

    This article presents an analysis of the impact of photovoltaic (PV) sources on the effectiveness and selectivity of earth fault protection in a 6 kV industrial distribution network. Simulations were conducted in the ATP-EMTP environment using a model of a generalized, real industrial network with an isolated neutral point. This model was based on data from real-world cases of earth faults with varying resistance. This study’s main objective was to determine how the power generated by PV sources affects the time and spectral waveforms of currents and zero-sequence voltages, in addition to the network’s overall response to disturbances. The results provide a quantitative assessment of the impact of distributed generation on the operational security of industrial power grids and form a basis for developing recommendations for coordinating protection in power systems integrated with renewable energy sources.

  • Open Access

    Artificial Aggregates from Metallurgical Waste as a Potential Source of Groundwater and Soil Contamination

    by Katarzyna Nowińska, Jacek Nowak, Aleksandra Bartyzel, Magdalena Kokowska-Pawłowska, Krzysztof Kuliński

    Highly developed countries generate large volumes of industrial waste, the type and quantity of which are strongly linked to the characteristics of the industries that produce it. Industrial waste can adversely affect the environment, so its disposal and management are a major challenge. Understanding the characteristics of a given waste type (e.g., its chemical and phase composition, technical parameters and likelihood of releasing constituents into aquatic and soil environments) allows its potential economic applications to be determined. A simple application of mineral waste is in the production of artificial aggregates, which are increasingly used as a substitute for natural aggregates. In Poland, artificial aggregates are widely produced from metallurgical waste from steel and non-ferrous metallurgy, which may contain numerous components that are potentially environmentally damaging. Depending on their occurrence form (i.e., mineral composition), these contaminants have varying potential to be released into aquatic and soil environments. This study presents the results of mineral and chemical composition analyses and leachability tests conducted on aggregates produced from metallurgical waste, including slags from blast furnaces, steelmaking, Zn and Pb production, and Ni production. The studied aggregates are characterised by chemical and phase composition differences, resulting from the type of slag from which they originate. The chemical composition of blast furnace slag is dominated by CaO, SiO2, Fe2O3, and MgO; steelmaking slag by CaO, Fe2O3, and SiO2; Zn and Pb production slag by SiO2, Fe2O3, SO3, and CaO; and Ni production slag by SiO2, Fe2O3, CaO, and Al2O3. The phase composition of all the tested aggregates is dominated by silicates resistant to leaching (weathering), which results in low levels of Al, Ca, Cr, Mn, Zn, Pb, Cu, As, Sr and Ni leaching, not exceeding 1.6%.

  • Open Access

    Microstructure and Mechanical Properties of AlSi10MnMg Alloy with Increased Content of Recycled Scrap

    by Jaroslaw Piatkowski, Katarzyna Nowinska, Tomasz Matula, Grzegorz Siwiec, Michal Szucki, Beata Oleksiak

    Increasing the share of circulating scrap in produced castings is not only due to optimizing production costs, but also the need to protect the environment realized by reducing production energy intensity, generating less waste, mitigating greenhouse gas emissions, and consuming fewer natural resources. However, this is associated with maintaining the required properties of castings and considering the impact of impurities on the formation of the structure of aluminum alloys. This research concerns the AlSi10MnMg alloy, which introduces 50 to 75% (every 5%) of circulating scrap. This alloy is one of the most commonly used for producing gravity and pressure die-castings (HPDC), including engine parts and transport structural elements. Based on microscopic research, it was found that the increase in scrap content causes an increase in the share of iron, which results in pre-eutectic (from about 0.45 wt.% to 0.7 wt.% Fe) or even primary crystallization of iron phases (over 0.7 wt.% Fe), mainly the plate–needle phase β-Al5FeSi. Its unfavorable morphology and size cause the formation of numerous shrinkage porosity areas, which has an impact on the reduction in mechanical properties (reduction in UTS and YS by approx. 16% and elongation by approx. 18%, compared to the AlSi10MnMg alloy with 50% scrap content). It was found that the increase in the share of recycled scrap (from 50 to 75%) can be used only when the manganese content is increased. Its effect is to change the morphology of the β-Al5FeSi phase into α-Al15(Fe,Mn)3Si2, whose crystallization occurs in the temperature range of 540 to 555 °C and increases slightly with increasing manganese addition. It is essential to consider the appropriate value of the Mn/Fe quotient, which should be about 1/2, because a higher value may cause the formation of a sludge factor. This work aimed to determine the limiting iron content (contained in the scrap) at which the sequence of the β-Al5FeSi phase release (pre-eutectic or primary crystallization) changes. This sequence mainly affects the form of morphology, the dimensions of the β-Fe phase, and the proportion of shrinkage porosity.