Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Zehua Chen has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Study of Retention of Drilling Fluid Layer on Annulus Wall during Cementing

    by Zhiqiang Wu, Zehua Chen, Chengwen Wang

    To guarantee that the cement sheath has a sealing effect, it is best to replace the drilling fluid entirely and fill the annulus with cement slurry throughout the cementing process. A significant driving power and high stability at the interface between the cement slurry and drilling fluid are often necessary for achieving a high displacement efficiency. It is important that a comprehensive theoretical characterization is established on the thickness and location of drilling fluid retention and the conditions to prevent the formation of drilling fluid retention. In this study, firstly, the characteristics of annulus fluid shear stress distribution are analyzed by establishing the differential equation of shear stress distribution. Subsequently, the calculation model of the drilling fluid retention layer’s thickness is constructed. Subsequently, the impact of cement slurry and drilling fluid properties, eccentricity of the casing, and additional variables on the annular wall’s drilling fluid retention thickness are scrutinized. The quantitative conditions for preventing drilling fluid retention are also analyzed (i.e., Equation (23)). Based on the newly developed model, a case study is conducted to show the significance of the new model. This offers a theoretical foundation for enhancing cement injection displacement efficiency and cementing performance optimization.


  • Open Access

    An Investigation into PVA Fiber Modified with SiO2 for Improving Mechanical Properties of Oil-Well Cements

    by Zhiqiang Wu, Zehua Chen, Jingping Liu, Chengwen Wang

    In this paper, we conduct a comprehensive investigation into PVA fiber modified with SiO2 to improve the mechanical properties of oil-well cements. Specifically, SiO2 was coated onto the surface of polyvinyl alcohol fiber (PVAF) as its silicon source via a sol-gel process by using tetraethyl orthosilicate (TEOS), while hydrochloric acid and ammonia were respectively used as the catalyst in the sol (hydrolysis) and the gel (condensation) processes. The PVAF microstructure was then characterized with the scanning electron microscope (SEM), while the effects of the modified PVAF on both mechanical and rheological properties of oil-well cements were examined. Due to the fact that SiO2 can be uniformly coated onto the PVAF surface, such modified PVAF can slightly improve the rheology of the cement slurry, while the raw PVAF exhibits poor dispersion at a high dosage. Compared with those of cement stone without PVAF after curing for 28 days at 60 °C, the flexural strength, compressive strength, and elastic modulus of the cement stone incorporated with the modified PVAFs were enhanced by 37.7%, 66.1%, and 50.0%, respectively. The SEM test (EDX) test, XRD test, and thermogravimetric test prove that the SiO2 coating on the PVAF surface can promote the hydration of cement clinker and can react with Ca(OH)2 to generate CSH gel. The SiO2 grafted onto the surface of PVAFs can improve the bond strength at the fiber/cement matrix interface, thus improving the mechanical properties of cement stone.


  • Open Access

    Theoretical and Experimental Study on Cementing Displacement Interface for Highly Deviated Wells

    by Zhiqiang Wu, Zehua Chen, Yipeng Zhao, Yucheng Xue, Chengwen Wang, Chao Xiong, Shunli Chen

    An effective drilling fluid removal is necessary to achieve an efficient cementing in oil and gas industry, i.e., it is ideal that all the drilling fluid is displaced by the cement slurry. The displacement efficiency is closely related to the stability and development of the displacing interface between the cementing slurry and drilling fluid. Thus, an effective cementing requires a validated theoretical model to describe the displacing interface to guide cementing applications, especially for highly deviated wells. The current studies suffer from a lack of experimental validation for proposed models. In this study, a theoretical model of cementing interfacial displacement in eccentric annulus is established. An experimental study is conducted to examine effects of well inclination, eccentricity and fluid properties on the stability of displacement interface to verify the theoretical model. The model is found to well describe the interface in the eccentric annulus, and it is applicable to the wellbore annulus with different inclination angles. The results show that: the displacement interface gradually extends (i.e., length is increased) with the increase of well inclination; the cement displacement effect became worse with deviation angle under the same injection and replacement conditions. Increasing the apparent viscosity of cement slurry is beneficial to improve the stability of displacement interface. In highly deviated wells, a certain casing eccentricity can inhibit the penetration of cement slurry in the wide gap of the low side of the annulus, which is conducive to maintaining the stability of the displacement interface.


  • Ultrasonic-Assisted Removal of Undesirable Submicron-Sized Particulates To Realize Sustainable and Eco-Friendly Circulation of Drilling Fluid

    by Chengwen Wang, Zehua Chen, Erding Chen, Junyi Liu, Fengfeng Xiao, Hongxiang Zhao

    Summary: Removal of useless and submicrometer-sized solids from drilling fluid, which exert significant effects on drilling performance, is a crucial part of sustainable and eco-friendly circulation in drilling operations. However, current solid-control methods for drilling-fluid reuse and recirculation, such as electronic-adsorption and chemical-flocculation methods, are associated with high cost and low efficiency and/or pollution of drilling fluid. In this study, a novel method using ultrasonic waves has been proposed to remove unwanted submicrometer-sized solids from polysulfonate drilling fluids. The results show that the suspension stability, viscosity, and particle size can all be significantly reduced, while the solid-separation ratio of the drilling fluid can be greatly enhanced by ultrasonic-wave treatment. The parameters of ultrasonic waves are optimized to be power of 3 kW, treating time of 30 minutes, treating frequency of 20 kHz, and ventilation (i.e., air) for 5 minutes in a laboratory scale. The scanning electron microscope (SEM) analysis shows that solid particles exhibit more obvious crystal morphology after ultrasonic-wave treatment, indicating that the breaking of gel-structure of drilling fluid due to the cavitation, mechanical, and heat effects of ultrasonic waves is the main mechanism for decreasing the suspension stability. Thus, the proposed ultrasonic-assisted technique has a high potential for removing undesirable solids from drilling fluid and fulfilling its recirculation in a cost-effective and environmentally friendly manner. This new technology has been successively applied to 12 wells, and good results were obtained.


  • Predicting Viscosities of Heavy Oils and Solvent–Heavy Oil Mixtures Using Artificial Neural Networks

    by Zehua Chen, Daoyong Yang

    This study investigates the potential of artificial neural networks (ANNs) to accurately predict viscosities of heavy oils (HOs) as well as mixtures of solvents and heavy oils (S–HOs). The study uses experimental data collected from the public domain for HO viscosities (involving 20 HOs and 568 data points) and S–HO mixture viscosities (involving 12 solvents and 4057 data points) for a wide range of temperatures, pressures, and mass fractions. The natural logarithm of viscosity (instead of viscosity itself) is used as predictor and response variables for the ANNs to significantly improve model performance. Gaps in HO viscosity data (with respect to pressure or temperature) are filled using either the existing correlations or ANN models that innovatively use viscosity ratios from the available data. HO viscosities and mixture viscosities (weight-based, molar-based, and volume-based) from the trained ANN models are found to be more accurate than those from commonly used empirical correlations and mixing rules. The trained ANN model also fares well for another dataset of condensate-diluted HOs.