Vincent Frick
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Vincent Frick has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Ehsan Jamshidpour
Université de Lorraine
7 shared publications - Milad Akrami
LEMTA Laboratory, Universit de Lorraine, Nancy, France
4 shared publications - Laurent Osberger
University of Freiburg,Microsystem Materials Laboratory, IMTEK,Freiburg,Germany
3 shared publications - Serge Pierfederici
Université de Lorraine, CNRS, LEMTA
3 shared publications - Foudil Dadouche
ICube Laboratory, University of Strasbourg and CNRS,Strasbourg,France
2 shared publications Liana Wassouf
Univ Strasbourg, ICube Lab, CNRS, 23 rue Loess, F-67037 Strasbourg, France
2 shared publications
Latest Publications
- Open Access
- 19 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 29226-29238
Trajectory Planning for Fast Dynamic One-Loop Flatness-Based Control of PMSMs
Permanent magnet (PM) motors are widely used in numerous industrial applications. Although the traditional proportional-integral (PI)-based field-oriented control (FOC) remains the most prevalent control method in industry, it has certain limitations. These include difficulties in handling system nonlinearities during constant changes in operating points, overlooking the saturation effects in permanent magnet synchronous motors (PMSMs), a trade-off between reference tracking and disturbance rejection, and limited dynamic performance due to its cascaded structure, particularly in fast-dynamic applications. Among the proposed nonlinear control methods for PMSMs, flatness-based (FB) control has demonstrated excellent performance in terms of reference tracking, disturbance rejection, and adaptability to saturation conditions. However, most FB control methods in the current literature utilize a cascaded structure to ensure system protection. To enhance one-loop FB control for applications requiring high dynamic performance and precise reference tracking, in this paper, a novel trajectory planning method is proposed to enable one-loop FB control for PMSM drives. This method considers system limits, such as current and switching voltage limits, during trajectory planning. The proposed method offers the advantage of relatively low computational requirements, allowing updates to be made in each switching period. The performance of the proposed method has been validated through both simulation studies and experimental tests on a dedicated testbench. The main novelty of this paper is the introduction of a new trajectory planning method for FB control of PMSMs. Unlike conventional cascaded structures, the proposed approach enables one-loop control while addressing the overcurrent limitation issues typically encountered in one-loop systems. This makes the method particularly suitable for applications that require high dynamic bandwidth, thanks to its simplified one-loop structure.
- 19 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 29226-29238
Open AccessTrajectory Planning for Fast Dynamic One-Loop Flatness-Based Control of PMSMs
Permanent magnet (PM) motors are widely used in numerous industrial applications. Although the traditional proportional-integral (PI)-based field-oriented control (FOC) remains the most prevalent control method in industry, it has certain limitations. These include difficulties in handling system nonlinearities during constant changes in operating points, overlooking the saturation effects in permanent magnet synchronous motors (PMSMs), a trade-off between reference tracking and disturbance rejection, and limited dynamic performance due to its cascaded structure, particularly in fast-dynamic applications. Among the proposed nonlinear control methods for PMSMs, flatness-based (FB) control has demonstrated excellent performance in terms of reference tracking, disturbance rejection, and adaptability to saturation conditions. However, most FB control methods in the current literature utilize a cascaded structure to ensure system protection. To enhance one-loop FB control for applications requiring high dynamic performance and precise reference tracking, in this paper, a novel trajectory planning method is proposed to enable one-loop FB control for PMSM drives. This method considers system limits, such as current and switching voltage limits, during trajectory planning. The proposed method offers the advantage of relatively low computational requirements, allowing updates to be made in each switching period. The performance of the proposed method has been validated through both simulation studies and experimental tests on a dedicated testbench. The main novelty of this paper is the introduction of a new trajectory planning method for FB control of PMSMs. Unlike conventional cascaded structures, the proposed approach enables one-loop control while addressing the overcurrent limitation issues typically encountered in one-loop systems. This makes the method particularly suitable for applications that require high dynamic bandwidth, thanks to its simplified one-loop structure.
- Open Access
- 1 March 2025
- Published by AIP Publishing in APL Electronic Devices
- Vol. 1 (1)
High power piezoelectric energy harvester for a temperature monitoring system
In this study, we present a lead-free, piezoelectric energy harvester capable of generating power in the milliwatt range. The harvester consists of four layers of polyvinylidene difluoride piezoelectric polymer, bonded to a cantilever with a tip mass. The cantilever’s resonance frequency was measured at 13.4 Hz. The piezoelectric layers are connected in parallel, resulting in a total capacitance of 27 nF. At resonance, under open-circuit conditions, the harvester generates nearly 90 Vpp when subjected to an acceleration of 1 g. When impedance is matched, the maximum power output reaches 2.4 mW. In addition, we integrated the harvester with commercially available signal conditioning cards, enabling conversion from an AC signal to a steady 3.3 V DC signal useful for electronics to evaluate their efficiency in charging a capacitor. Finally, we demonstrated the harvester’s functionality in an autonomous system that measures and displays temperature on a digital screen. The system operated autonomously for 6.5 h.
- 1 March 2025
- Published by AIP Publishing in APL Electronic Devices
- Vol. 1 (1)
Open AccessHigh power piezoelectric energy harvester for a temperature monitoring system
In this study, we present a lead-free, piezoelectric energy harvester capable of generating power in the milliwatt range. The harvester consists of four layers of polyvinylidene difluoride piezoelectric polymer, bonded to a cantilever with a tip mass. The cantilever’s resonance frequency was measured at 13.4 Hz. The piezoelectric layers are connected in parallel, resulting in a total capacitance of 27 nF. At resonance, under open-circuit conditions, the harvester generates nearly 90 Vpp when subjected to an acceleration of 1 g. When impedance is matched, the maximum power output reaches 2.4 mW. In addition, we integrated the harvester with commercially available signal conditioning cards, enabling conversion from an AC signal to a steady 3.3 V DC signal useful for electronics to evaluate their efficiency in charging a capacitor. Finally, we demonstrated the harvester’s functionality in an autonomous system that measures and displays temperature on a digital screen. The system operated autonomously for 6.5 h.
- Open Access
Application of Low-Resolution Hall Position Sensor in Control and Position Estimation of PMSM—A Review
This paper reviews the application of Hall position sensors in control and position estimation of permanent magnet synchronous motors (PMSMs). Accurate rotor position and motor speed data are essential for the high-efficiency control of PMSMs in modern industry. Rotor position and motor speed can be measured by mechanical position sensors, which are costly and less reliable, or by rotor position observers, which are sensitive to system models and changes in motor parameters. This paper examines the benefits, limitations, challenges, and uses of low-resolution Hall position sensors in PMSM drives, presenting them as a cost-effective solution for achieving a balance between performance and expense. In addition, the paper discusses recent solutions to issues related to misplaced Hall position sensors and fault-tolerant control algorithms, and gives an outlook to future developments in this area.
Open AccessApplication of Low-Resolution Hall Position Sensor in Control and Position Estimation of PMSM—A Review
This paper reviews the application of Hall position sensors in control and position estimation of permanent magnet synchronous motors (PMSMs). Accurate rotor position and motor speed data are essential for the high-efficiency control of PMSMs in modern industry. Rotor position and motor speed can be measured by mechanical position sensors, which are costly and less reliable, or by rotor position observers, which are sensitive to system models and changes in motor parameters. This paper examines the benefits, limitations, challenges, and uses of low-resolution Hall position sensors in PMSM drives, presenting them as a cost-effective solution for achieving a balance between performance and expense. In addition, the paper discusses recent solutions to issues related to misplaced Hall position sensors and fault-tolerant control algorithms, and gives an outlook to future developments in this area.
- Open Access
- 12 July 2024
- Published by EDP Sciences in J3eA
- Vol. 23, 1007
Système Embarqué de Type Nœud IoT Communicant Sans Fil
Cet article présente la réalisation d’un système embarqué remplissant la fonction de nœud IoT (Internet of Things) mené dans le cadre d’une Situation d’Apprentissage et d’Évaluation (SAÉ). Les étudiants conçoivent un système chargé de mettre en œuvre un capteur environnemental (température, humidité, etc.) numérique ayant un protocole non-conventionnel. Les données du capteur sont gérées par un processeur embarqué et transmises au moyen d’un module de communication radiofréquence. En outre, le système exploite le protocole de communication MQTT pour communiquer avec des clients mobiles. Les étudiants montrent un fort intérêt pour ce projet pluridisciplinaire, qui comporte également une partie dédiée au développement d’une application mobile particulièrement ludique. Les résultats obtenus montrent par ailleurs qu’ils atteignent globalement les objectifs et valident les compétences attendues.
- 12 July 2024
- Published by EDP Sciences in J3eA
- Vol. 23, 1007
Open AccessSystème Embarqué de Type Nœud IoT Communicant Sans Fil
Cet article présente la réalisation d’un système embarqué remplissant la fonction de nœud IoT (Internet of Things) mené dans le cadre d’une Situation d’Apprentissage et d’Évaluation (SAÉ). Les étudiants conçoivent un système chargé de mettre en œuvre un capteur environnemental (température, humidité, etc.) numérique ayant un protocole non-conventionnel. Les données du capteur sont gérées par un processeur embarqué et transmises au moyen d’un module de communication radiofréquence. En outre, le système exploite le protocole de communication MQTT pour communiquer avec des clients mobiles. Les étudiants montrent un fort intérêt pour ce projet pluridisciplinaire, qui comporte également une partie dédiée au développement d’une application mobile particulièrement ludique. Les résultats obtenus montrent par ailleurs qu’ils atteignent globalement les objectifs et valident les compétences attendues.
- Open Access
- 3 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 92451-92463
A Novel Trajectory Planning for One-Loop Flatness-Based Control of PMSM
Permanent Magnet Synchronous Motors (PMSMs) are used in a variety of industries, including aerospace, industrial control, and electric vehicles (EVs). Extensive research has been dedicated to the control and drive of PMSMs, with field-oriented control (FOC) gaining prominence in today’s industry. Despite its popularity, the nonlinear nature of the PMSM drive system impacts the dynamic performance when employing the traditional Proportional-Integral (PI)-based FOC method, particularly under varying operating points. Over the last decade, flatness-based control has emerged as a viable alternative to PI-based FOC in response to system nonlinearity. As a traditional approach, a cascaded flatness-based control structure has been proposed in the literature. This method, however, has lower dynamic performance due to its cascaded structure. The flatness-based control with only one control loop is suggested for improving the dynamic performance of the flatness-based control, especially for high-speed and low-inertia systems. This method, however, lacks current protection. This paper introduces a novel trajectory planning approach for the one-loop flatness-based control of PMSM drives. The focus is on addressing controller limits, an aspect that has received limited attention thus far. The proposed approach ensures control stability by considering the constraints of the maximum motor current (determined by the electrical specifications of the motor and driver) and the switching voltages, which depend on the DC-bus voltage. The method’s effectiveness is validated through simulation studies and experimental tests.
- 3 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 92451-92463
Open AccessA Novel Trajectory Planning for One-Loop Flatness-Based Control of PMSM
Permanent Magnet Synchronous Motors (PMSMs) are used in a variety of industries, including aerospace, industrial control, and electric vehicles (EVs). Extensive research has been dedicated to the control and drive of PMSMs, with field-oriented control (FOC) gaining prominence in today’s industry. Despite its popularity, the nonlinear nature of the PMSM drive system impacts the dynamic performance when employing the traditional Proportional-Integral (PI)-based FOC method, particularly under varying operating points. Over the last decade, flatness-based control has emerged as a viable alternative to PI-based FOC in response to system nonlinearity. As a traditional approach, a cascaded flatness-based control structure has been proposed in the literature. This method, however, has lower dynamic performance due to its cascaded structure. The flatness-based control with only one control loop is suggested for improving the dynamic performance of the flatness-based control, especially for high-speed and low-inertia systems. This method, however, lacks current protection. This paper introduces a novel trajectory planning approach for the one-loop flatness-based control of PMSM drives. The focus is on addressing controller limits, an aspect that has received limited attention thus far. The proposed approach ensures control stability by considering the constraints of the maximum motor current (determined by the electrical specifications of the motor and driver) and the switching voltages, which depend on the DC-bus voltage. The method’s effectiveness is validated through simulation studies and experimental tests.
- 10 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (1) , 135-152
Sensorless Control Methods for BLDC Motor Drives: A Review
Permanent magnet motors, such as Brushless DC (BLDC) motors, are widely adopted in today’s industry for their high power density, torque-to-weight ratio, and uncomplicated design. Furthermore, electrical motor drive systems are increasingly adopting (position) sensorless control methods. Sensorless techniques have several advantages over sensor-based methods, including enhanced reliability, prolonged motor lifespans, simplified inverter-motor connections, and lower costs. Several sensorless techniques have been proposed over the past few decades, such as methods based on terminal voltage measurement, third harmonic back electromotive force (back-EMF) signals, and estimation methods. Research in recent years has focused on improving conventional sensorless methods and developing new ones, including those based on flux linkage functions and neural networks. These advancements address challenges associated with high-speed BLDC drives where the phase lag of the LPF is significant, tackle issues in very low-speed applications where back-EMF signal amplitudes are low, improve position estimation speed to enable one-cycle estimation, enhance control system accuracy for BLDC motors with nonideal back-EMFs, and consider asymmetric back-EMF signals. This paper examines the benefits, limitations, and challenges of sensorless drives for BLDC motors, alongside innovative solutions for nonideal and asymmetric back-EMF issues, with an eye toward future developments.
- 10 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (1) , 135-152
Sensorless Control Methods for BLDC Motor Drives: A Review
Permanent magnet motors, such as Brushless DC (BLDC) motors, are widely adopted in today’s industry for their high power density, torque-to-weight ratio, and uncomplicated design. Furthermore, electrical motor drive systems are increasingly adopting (position) sensorless control methods. Sensorless techniques have several advantages over sensor-based methods, including enhanced reliability, prolonged motor lifespans, simplified inverter-motor connections, and lower costs. Several sensorless techniques have been proposed over the past few decades, such as methods based on terminal voltage measurement, third harmonic back electromotive force (back-EMF) signals, and estimation methods. Research in recent years has focused on improving conventional sensorless methods and developing new ones, including those based on flux linkage functions and neural networks. These advancements address challenges associated with high-speed BLDC drives where the phase lag of the LPF is significant, tackle issues in very low-speed applications where back-EMF signal amplitudes are low, improve position estimation speed to enable one-cycle estimation, enhance control system accuracy for BLDC motors with nonideal back-EMFs, and consider asymmetric back-EMF signals. This paper examines the benefits, limitations, and challenges of sensorless drives for BLDC motors, alongside innovative solutions for nonideal and asymmetric back-EMF issues, with an eye toward future developments.
- 4 September 2023
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 116 (3) , 145-159
Optimization of an SSHC-based full active rectifier for piezoelectric energy harvesting
- 4 September 2023
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 116 (3) , 145-159
Optimization of an SSHC-based full active rectifier for piezoelectric energy harvesting
- 30 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (2) , 532-536
MPPT Technique With Improved FOCV Control Applied to a Full Active Rectifier for Low-Voltage Piezoelectric Energy Harvesting
An improved ultra low power fractional open circuit voltage (FOCV) MPPT implementation for the inductorless full active rectifier (FAR) piezoelectric energy harvesting interface is presented in this paper. The proposed MPPT reduces the circuit’s disconnection time from the load by performing sampling of the optimal output regulation voltage in only half of a period. Additionally, the power consumption of this approach is remarkably low since it relies on a limited number of mainly passive components. The experimental results from the discrete circuit prototype revealed that the proposed MPPT strategy has 91% efficiency and a power conception of 0.3mW. Furthermore, the system operates at very low open circuit voltages (VOC) in the order of 0.5V with high efficiency thanks to the FAR interface
- 30 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (2) , 532-536
MPPT Technique With Improved FOCV Control Applied to a Full Active Rectifier for Low-Voltage Piezoelectric Energy Harvesting
An improved ultra low power fractional open circuit voltage (FOCV) MPPT implementation for the inductorless full active rectifier (FAR) piezoelectric energy harvesting interface is presented in this paper. The proposed MPPT reduces the circuit’s disconnection time from the load by performing sampling of the optimal output regulation voltage in only half of a period. Additionally, the power consumption of this approach is remarkably low since it relies on a limited number of mainly passive components. The experimental results from the discrete circuit prototype revealed that the proposed MPPT strategy has 91% efficiency and a power conception of 0.3mW. Furthermore, the system operates at very low open circuit voltages (VOC) in the order of 0.5V with high efficiency thanks to the FAR interface
- Open Access
- 7 July 2022
- Published by Springer Nature in Research Square
Optimization of an SSHC-Based Full Active Rectifier for Piezoelectric Energy Harvesting
This paper presents a compact and efficient integrated interface circuit for piezo-electric energy harvesting. While the state-of-the-art interface circuits require the use of either an external inductor or a significant number of additional capacitors to achieve high voltage flip and improve power efficiency, the proposed Full Active Rectifier on Flipping Capac-itor (FAR-FC) is based on a reduced set of flipping capacitors and an active rectifier to efficiently flip the voltage across the piezoelec-tric transducer. In addition, this optimized SSHC circuit reaches better power efficiency when the piezoelectric transducer is operating under low mechanical excitation, i.e. when the open-circuit voltage of the piezoelectric transducer is V oc = 1V , while this value is usually V oc ≥ 2V in literature. Furthermore, the FAR-FC supports piezo-electric transducers with higher inherent capacitance values compared to those usually reported in literature, which makes the circuit potentially suitable for a larger variety of MEMS applications. The interface circuit was designed and fabricated in a 0.35-µm CMOS process. Measurement results show that the voltage flip efficiency goes up to 90%. It also reveals that the proposed FAR-FC circuit achieves power performance up to 5.64× higher than a conventional full-bridge rectifier.
- 7 July 2022
- Published by Springer Nature in Research Square
Open AccessOptimization of an SSHC-Based Full Active Rectifier for Piezoelectric Energy Harvesting
This paper presents a compact and efficient integrated interface circuit for piezo-electric energy harvesting. While the state-of-the-art interface circuits require the use of either an external inductor or a significant number of additional capacitors to achieve high voltage flip and improve power efficiency, the proposed Full Active Rectifier on Flipping Capac-itor (FAR-FC) is based on a reduced set of flipping capacitors and an active rectifier to efficiently flip the voltage across the piezoelec-tric transducer. In addition, this optimized SSHC circuit reaches better power efficiency when the piezoelectric transducer is operating under low mechanical excitation, i.e. when the open-circuit voltage of the piezoelectric transducer is V oc = 1V , while this value is usually V oc ≥ 2V in literature. Furthermore, the FAR-FC supports piezo-electric transducers with higher inherent capacitance values compared to those usually reported in literature, which makes the circuit potentially suitable for a larger variety of MEMS applications. The interface circuit was designed and fabricated in a 0.35-µm CMOS process. Measurement results show that the voltage flip efficiency goes up to 90%. It also reveals that the proposed FAR-FC circuit achieves power performance up to 5.64× higher than a conventional full-bridge rectifier.
- Open Access
- 10 June 2022
- Published by EDP Sciences in J3eA
- Vol. 21, 1022
Conception de système embarqué sur cible FPGA : une approche par compétences
Cet article témoigne d’une expérience d’approche par compétence appliquée dans le cadre de modules d’enseignement aux systèmes électroniques embarqués. Les projets proposés aux étudiants visent à développer les compétences qui leur permettront de répondre efficacement à un cahier des charges dans un domaine où matériels et logiciels sont en constante évolution. En l’occurrence, il s’agit d’encourager l’initiative dans les choix techniques de co-conception de circuits numériques impliquant le langage de description matériel VHDL, la synthèse de processeur embarqué, la programmation en langage C. Le retour d’expérience montre qu’au prix d’un suivi régulier de la progression des étudiants, les résultats et le taux de satisfaction des étudiants sont très élevés et peuvent même dépasser les objectifs initiaux.
- 10 June 2022
- Published by EDP Sciences in J3eA
- Vol. 21, 1022
Open AccessConception de système embarqué sur cible FPGA : une approche par compétences
Cet article témoigne d’une expérience d’approche par compétence appliquée dans le cadre de modules d’enseignement aux systèmes électroniques embarqués. Les projets proposés aux étudiants visent à développer les compétences qui leur permettront de répondre efficacement à un cahier des charges dans un domaine où matériels et logiciels sont en constante évolution. En l’occurrence, il s’agit d’encourager l’initiative dans les choix techniques de co-conception de circuits numériques impliquant le langage de description matériel VHDL, la synthèse de processeur embarqué, la programmation en langage C. Le retour d’expérience montre qu’au prix d’un suivi régulier de la progression des étudiants, les résultats et le taux de satisfaction des étudiants sont très élevés et peuvent même dépasser les objectifs initiaux.