Alexander J. Carpenter
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alexander J. Carpenter has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Sidney Chocron
Southwest Research Institute, San Antonio, USA
4 shared publications Sidney Chocron
3 shared publicationsCharles E Anderson
Engineering Dynamics Department, Southwest Research Institute, P.O. Drawer 28510, San Antonio, TX, USA
2 shared publications- Andrew Williams1 shared publication
Ashley Mullins
1 shared publicationC. E. Anderson
CEA Consulting, San Antonio, USA
1 shared publication
Latest Publications
- 15 July 2025
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 206
Methodology for soft catch of ballistic projectiles using multi-layer foam targets
- 15 July 2025
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 206
Methodology for soft catch of ballistic projectiles using multi-layer foam targets
- 14 July 2024
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 193
Strain waves on additively manufactured plates for an on-orbit impact detector concept
- 14 July 2024
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 193
Strain waves on additively manufactured plates for an on-orbit impact detector concept
- 18 April 2023
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 9 (2) , 225-239
Characterization, Modeling, and Ballistic Impact of Kevlar/Phenolic PVB Composite
- 18 April 2023
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 9 (2) , 225-239
Characterization, Modeling, and Ballistic Impact of Kevlar/Phenolic PVB Composite
- 18 December 2017
- Published by DEStech Publications
Mesoscale and Continuum Modeling of Ballistic Impact on s-2 glass/sc-15 Epoxy Composite Panels
Recently, the authors developed two modeling approaches for composite materials that have been validated against a battery of plain-woven S-2 glass/SC-15 epoxy composite slow-rate mechanical test data. In one approach, a mesoscale mesh was created, and individual yarns, the surrounding matrix, and interfaces were represented using separate simple material models. For the other approach, rules of mixtures were used to relate stresses and strains at the fiber/matrix level to those averaged over the composite as a whole, which allows the composite to be represented by a continuum-level mesh. In this study, both models were used to simulate the ballistic impact of S-2 glass composite panels by two projectiles: a soft M80 ball round and a hard 0.50-cal fragment simulating projectile. Ballistic limits, residual velocities, backface deflections, and delamination areas from the simulations are compared to test data. The relative advantages and disadvantages of the two models are discussed with regard to both accuracy and computational runtime.
- 18 December 2017
- Published by DEStech Publications
Mesoscale and Continuum Modeling of Ballistic Impact on s-2 glass/sc-15 Epoxy Composite Panels
Recently, the authors developed two modeling approaches for composite materials that have been validated against a battery of plain-woven S-2 glass/SC-15 epoxy composite slow-rate mechanical test data. In one approach, a mesoscale mesh was created, and individual yarns, the surrounding matrix, and interfaces were represented using separate simple material models. For the other approach, rules of mixtures were used to relate stresses and strains at the fiber/matrix level to those averaged over the composite as a whole, which allows the composite to be represented by a continuum-level mesh. In this study, both models were used to simulate the ballistic impact of S-2 glass composite panels by two projectiles: a soft M80 ball round and a hard 0.50-cal fragment simulating projectile. Ballistic limits, residual velocities, backface deflections, and delamination areas from the simulations are compared to test data. The relative advantages and disadvantages of the two models are discussed with regard to both accuracy and computational runtime.
- Open Access
- 1 January 2017
- Published by Elsevier in Procedia Engineering
- Vol. 204, 383-389
Linking the equation of state for fiber-reinforced composites to those of the individual fiber and matrix constituents
- 1 January 2017
- Published by Elsevier in Procedia Engineering
- Vol. 204, 383-389
Open AccessLinking the equation of state for fiber-reinforced composites to those of the individual fiber and matrix constituents
- Open Access
- 1 January 2017
- Published by Elsevier in Procedia Engineering
- Vol. 204, 154-161
Hypervelocity Impact on Pumice: Scale Effects on Experiments and Simulations
- 1 January 2017
- Published by Elsevier in Procedia Engineering
- Vol. 204, 154-161
Open AccessHypervelocity Impact on Pumice: Scale Effects on Experiments and Simulations
- 28 July 2016
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 50 (24) , 3431-3443
Mesoscale modeling of S-2 Glass/SC-15 epoxy composites: 3D-weave architecture
The addition of Z-yarns to an S-2 glass composite can increase the material's resistance to interlayer delamination and damage. However, the presence of the Z-yarns also complicates the resulting constitutive behavior, as multiple individual failure mechanisms (e.g. yarn/matrix delamination, yarn breakage) may occur before the overall ultimate failure of the composite is reached. A mesoscale model of a 3D-weave composite was created to provide insights into these processes. Material models for the yarns, matrix, and interfaces were previously developed for a similar plain-weave composite. These were combined with a complicated unit cell geometry that could be used to construct specimen meshes that closely matched the physical characteristics of the 3D-weave composite. Numerical simulations conducted using this model can reproduce most aspects of the load–displacement curves and the observed failure mechanisms from tension, torsion, and delamination tests.
- 28 July 2016
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 50 (24) , 3431-3443
Mesoscale modeling of S-2 Glass/SC-15 epoxy composites: 3D-weave architecture
The addition of Z-yarns to an S-2 glass composite can increase the material's resistance to interlayer delamination and damage. However, the presence of the Z-yarns also complicates the resulting constitutive behavior, as multiple individual failure mechanisms (e.g. yarn/matrix delamination, yarn breakage) may occur before the overall ultimate failure of the composite is reached. A mesoscale model of a 3D-weave composite was created to provide insights into these processes. Material models for the yarns, matrix, and interfaces were previously developed for a similar plain-weave composite. These were combined with a complicated unit cell geometry that could be used to construct specimen meshes that closely matched the physical characteristics of the 3D-weave composite. Numerical simulations conducted using this model can reproduce most aspects of the load–displacement curves and the observed failure mechanisms from tension, torsion, and delamination tests.
- 23 January 2016
- Published by Springer Nature in Microfluidics and Nanofluidics
- Vol. 20 (2) , 1-14
Coupled RapidCell and lattice Boltzmann models to simulate hydrodynamics of bacterial transport in response to chemoattractant gradients in confined domains
- 23 January 2016
- Published by Springer Nature in Microfluidics and Nanofluidics
- Vol. 20 (2) , 1-14
Coupled RapidCell and lattice Boltzmann models to simulate hydrodynamics of bacterial transport in response to chemoattractant gradients in confined domains
- 15 April 2015
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 50 (5) , 685-700
Mesoscale modeling of S-2 glass/SC-15 epoxy composites: Plain-weave architecture
S-2 glass composites can readily serve as backing materials for armor systems due to their light weight and tensile properties. However, high-fidelity ballistic modeling of these composites requires accurate predictions of their nonlinear deformation and failure behaviors, which can prove challenging. This paper describes simulations of a plain-weave S-2 glass composite at the mesoscale using a mesh geometry that individually models the S-2 glass yarns, epoxy resin matrix, and yarn/matrix interfaces as separate entities. Simulation results are compared to a wide variety of mechanical tests designed to measure the response of the composite to tension, shear, and delamination. Although the individual yarns, matrix, and interfaces are described using relatively simple material models, the overall composite model can accurately reproduce behaviors such as nonlinear deformation, yarn breakage, and delamination in both tension and shear.
- 15 April 2015
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 50 (5) , 685-700
Mesoscale modeling of S-2 glass/SC-15 epoxy composites: Plain-weave architecture
S-2 glass composites can readily serve as backing materials for armor systems due to their light weight and tensile properties. However, high-fidelity ballistic modeling of these composites requires accurate predictions of their nonlinear deformation and failure behaviors, which can prove challenging. This paper describes simulations of a plain-weave S-2 glass composite at the mesoscale using a mesh geometry that individually models the S-2 glass yarns, epoxy resin matrix, and yarn/matrix interfaces as separate entities. Simulation results are compared to a wide variety of mechanical tests designed to measure the response of the composite to tension, shear, and delamination. Although the individual yarns, matrix, and interfaces are described using relatively simple material models, the overall composite model can accurately reproduce behaviors such as nonlinear deformation, yarn breakage, and delamination in both tension and shear.