Shaobin Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Shaobin Li has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Xizhen Song
School of Energy and Power Engineering, Beijing University of Aeronautics and Astronautics, Beijing 101191, China
3 shared publications - Hefeng Dong
Systems Engineering Research Institute, China State Shipbuilding Corporation Limited, Beijing 100194, China
2 shared publications - Shamiao Luo
School of Energy and Power Engineering, Beijing University of Aeronautics and Astronautics, Beijing 101191, China
2 shared publications - Shoulie Liu
School of Energy and Power Engineering, Beijing University of Aeronautics and Astronautics, Beijing 101191, China
2 shared publications - Changan Huang
Systems Engineering Research Institute, China State Shipbuilding Corporation Limited, Beijing 100194, China
1 shared publication - Jiao Sun
Xinxiang Simo Blower Co., Ltd., Xinxiang 453000, China
1 shared publication
Latest Publications
- Open Access
Coupled Flow and Swirl-Distortion Characteristics of a Lateral Intake–Axial Fan Interaction
Lateral intakes generate distorted inflow and complex swirl structures upstream of axial fans. Steady and unsteady numerical simulations were performed to investigate the coupled flow field between a lateral intake and an axial-fan rotor. The local normalized axial mass-flux factor φ, together with swirl descriptors, was employed to characterize the flow structure. The results show that swirl distortion at the aerodynamic interface plane (AIP) exhibits distinct radial stratification and circumferential non-uniformity, and that these characteristics vary with operating conditions. The circumferential non-uniformity is associated with the lateral-intake inflow, whereas the pronounced near-tip variation is consistent with an increasing influence of rotor-related tip flow structures at lower flow rates. In the unsteady analysis, periodic fluctuations of φ, SD, and SI vary with spanwise and circumferential location and are strongest near the blade tip. A non-zero frequency component between the rotational frequency and blade-passing frequency is identified in φ, SD, and SI over the entire blade span rather than being confined to the tip region. It indicates that the component is likely associated with the interaction between the circumferentially non-uniform intake flow and the rotor motion. These findings provide a basis for further investigation of rotor aerodynamic loading under distorted inflow conditions.
Open AccessCoupled Flow and Swirl-Distortion Characteristics of a Lateral Intake–Axial Fan Interaction
Lateral intakes generate distorted inflow and complex swirl structures upstream of axial fans. Steady and unsteady numerical simulations were performed to investigate the coupled flow field between a lateral intake and an axial-fan rotor. The local normalized axial mass-flux factor φ, together with swirl descriptors, was employed to characterize the flow structure. The results show that swirl distortion at the aerodynamic interface plane (AIP) exhibits distinct radial stratification and circumferential non-uniformity, and that these characteristics vary with operating conditions. The circumferential non-uniformity is associated with the lateral-intake inflow, whereas the pronounced near-tip variation is consistent with an increasing influence of rotor-related tip flow structures at lower flow rates. In the unsteady analysis, periodic fluctuations of φ, SD, and SI vary with spanwise and circumferential location and are strongest near the blade tip. A non-zero frequency component between the rotational frequency and blade-passing frequency is identified in φ, SD, and SI over the entire blade span rather than being confined to the tip region. It indicates that the component is likely associated with the interaction between the circumferentially non-uniform intake flow and the rotor motion. These findings provide a basis for further investigation of rotor aerodynamic loading under distorted inflow conditions.
- Open Access
A Multi-Parameter Collaborative Dimensionless Fan Selection Method Based on Efficiency Optimization
This paper proposes an efficiency-optimized multi-parameter collaborative non-dimensional selection method for industrial fans. Based on fan similarity theory, selection parameters are transformed into non-dimensional forms. The fan’s best working area (BWA) is defined according to stall margin, flow range, total pressure rise deviation, and minimum efficiency. The initial model selection uses the boundary equations of the defined BWA as screening criteria. Decision parameters comprise Euclidean distance, design point distance, pressure deviation, and current efficiency. These collectively form a multi-objective evaluation function. The NSGA-II algorithm determines the optimal weight distribution of decision parameters, generating a Pareto-optimal solution set. The initially selected models are subsequently subjected to secondary optimization through a comprehensive evaluation function. Selection case studies demonstrate that this method preliminarily screens 7 models that meet the target parameters from 400 candidate models. Secondary screening determines the model with the optimal efficiency and best comprehensive evaluation performance. The method effectively resolves the mismatch between fan model design points and target operational parameters in selection processes. This method integrates directly into selection software platforms and validation with 100 sets of fan selection parameters demonstrates that selected models achieve 99% accuracy. Achieving the secondary optimization function for fan model selection.
Open AccessA Multi-Parameter Collaborative Dimensionless Fan Selection Method Based on Efficiency Optimization
This paper proposes an efficiency-optimized multi-parameter collaborative non-dimensional selection method for industrial fans. Based on fan similarity theory, selection parameters are transformed into non-dimensional forms. The fan’s best working area (BWA) is defined according to stall margin, flow range, total pressure rise deviation, and minimum efficiency. The initial model selection uses the boundary equations of the defined BWA as screening criteria. Decision parameters comprise Euclidean distance, design point distance, pressure deviation, and current efficiency. These collectively form a multi-objective evaluation function. The NSGA-II algorithm determines the optimal weight distribution of decision parameters, generating a Pareto-optimal solution set. The initially selected models are subsequently subjected to secondary optimization through a comprehensive evaluation function. Selection case studies demonstrate that this method preliminarily screens 7 models that meet the target parameters from 400 candidate models. Secondary screening determines the model with the optimal efficiency and best comprehensive evaluation performance. The method effectively resolves the mismatch between fan model design points and target operational parameters in selection processes. This method integrates directly into selection software platforms and validation with 100 sets of fan selection parameters demonstrates that selected models achieve 99% accuracy. Achieving the secondary optimization function for fan model selection.
- Open Access
Study on Rain Absorption Performance and Flow Field of Transonic Compressor under Different Working Conditions
Taking a four-stage transonic compressor as the research object, the Lagrange particle tracking method was used to simulate the multiphase flow by considering the particle fragmentation, collision and evaporation models, and the influence of different inlet conditions (raindrop diameter, velocity, temperature and flow rate) on the compressor’s performance and stable working range was studied. The results show that inlet rain absorption can weaken the clearance leakage vortex make the shock wave move downstream, thus increasing the inlet flow rate, resulting in a decrease in stability margin and the highest efficiency point moving in the direction of flow increase. With the decrease in raindrop diameter, the pressure ratio and wet compression efficiency increase, and the stability margin decreases. With the increase in inlet raindrop velocity, the degree of pneumatic breakage increases and the raindrop diameter becomes smaller, which leads to the decrease in pressure ratio and efficiency. The influence of the mass flow rate of imported raindrops on the stable working range is significant. When the mass flow rate of imported raindrops accounts for 5% of the design flow, the stable working range can be reduced by more than half. Rain absorption increases the reaction force of the compressor and increases the load of the rotor blade.
Open AccessStudy on Rain Absorption Performance and Flow Field of Transonic Compressor under Different Working Conditions
Taking a four-stage transonic compressor as the research object, the Lagrange particle tracking method was used to simulate the multiphase flow by considering the particle fragmentation, collision and evaporation models, and the influence of different inlet conditions (raindrop diameter, velocity, temperature and flow rate) on the compressor’s performance and stable working range was studied. The results show that inlet rain absorption can weaken the clearance leakage vortex make the shock wave move downstream, thus increasing the inlet flow rate, resulting in a decrease in stability margin and the highest efficiency point moving in the direction of flow increase. With the decrease in raindrop diameter, the pressure ratio and wet compression efficiency increase, and the stability margin decreases. With the increase in inlet raindrop velocity, the degree of pneumatic breakage increases and the raindrop diameter becomes smaller, which leads to the decrease in pressure ratio and efficiency. The influence of the mass flow rate of imported raindrops on the stable working range is significant. When the mass flow rate of imported raindrops accounts for 5% of the design flow, the stable working range can be reduced by more than half. Rain absorption increases the reaction force of the compressor and increases the load of the rotor blade.
- Open Access
- 9 September 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (17) , 8070
Numerical Study of Internal Flow Field in a Disc Stack Centrifuge Based on Mixture-PBM Model
Disc stack centrifuge belongs to one kind of sedimentation centrifuge, widely used in the environmental protection, pharmacy, and chemical industries, etc. The flow process inside the disc stack centrifuge seriously affects the separation efficiency. However, the flow process inside the disc stack centrifuge and its influence on the separation efficiency have not yet been detailed. We plan to study the flow process of oil and water phases inside the disc stack centrifuge and to explore the process of fragmentation and accumulation of water droplets. In this study, the Mixture-PBM (Population Balance Model) model is used to numerically simulate the two-phase flow of oil and water in the disc stack centrifuge and compare it with the tests. The research found that with the increase in rotational speed, the separation efficiency rises in both the test and numerical simulation results, and the difference between the test and simulation results is below 1%. The effect of ribs on the flow is considered, and the results show that the hysteresis of the liquid flow in the disc stack centrifuge is significantly reduced after considering the ribs, and the numerical simulation results can reach 98% of the theoretical results. Fluid entering the separation channel from the neutral pore creates a vortex, and as the dimensionless number λ increases, the degree of deviation of the fluid’s trajectory from the generatrix increases. The circumferential and radial velocities in the separation channel appear large in the center and small near the wall. The water content in the rising channel gradually decreases, and 90% of the water finishes settling in the distributor. The processing volume of the separation channel in each layer shows a small bottom layer, a large top layer, and a uniform law in the middle. The coalescence of water droplets occurs mainly in the separation channel, as found by analyzing the laws of the internal flow of the disc stack centrifuge, which provides the basis for improving the structure of the disc stack centrifuge, increasing the separation efficiency and reducing the floor space.
- 9 September 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (17) , 8070
Open AccessNumerical Study of Internal Flow Field in a Disc Stack Centrifuge Based on Mixture-PBM Model
Disc stack centrifuge belongs to one kind of sedimentation centrifuge, widely used in the environmental protection, pharmacy, and chemical industries, etc. The flow process inside the disc stack centrifuge seriously affects the separation efficiency. However, the flow process inside the disc stack centrifuge and its influence on the separation efficiency have not yet been detailed. We plan to study the flow process of oil and water phases inside the disc stack centrifuge and to explore the process of fragmentation and accumulation of water droplets. In this study, the Mixture-PBM (Population Balance Model) model is used to numerically simulate the two-phase flow of oil and water in the disc stack centrifuge and compare it with the tests. The research found that with the increase in rotational speed, the separation efficiency rises in both the test and numerical simulation results, and the difference between the test and simulation results is below 1%. The effect of ribs on the flow is considered, and the results show that the hysteresis of the liquid flow in the disc stack centrifuge is significantly reduced after considering the ribs, and the numerical simulation results can reach 98% of the theoretical results. Fluid entering the separation channel from the neutral pore creates a vortex, and as the dimensionless number λ increases, the degree of deviation of the fluid’s trajectory from the generatrix increases. The circumferential and radial velocities in the separation channel appear large in the center and small near the wall. The water content in the rising channel gradually decreases, and 90% of the water finishes settling in the distributor. The processing volume of the separation channel in each layer shows a small bottom layer, a large top layer, and a uniform law in the middle. The coalescence of water droplets occurs mainly in the separation channel, as found by analyzing the laws of the internal flow of the disc stack centrifuge, which provides the basis for improving the structure of the disc stack centrifuge, increasing the separation efficiency and reducing the floor space.
- Open Access
Study on the Influence of Working Characteristics of Centripetal Pump Based on VOF/Mixture Model
Aviation fuel contamination can seriously affect aircraft flight safety, and the centripetal pump is the core component of aviation fuel purification equipment. The performance of centripetal pumps is highly demanded for purification equipment. The operating parameters of centripetal pumps significantly affect the internal flow characteristics, which affects the performance of centripetal pumps. However, the flow characteristics of a centripetal pump influenced by the operating parameters have not yet been elaborated upon. In this research, a three-dimensional numerical simulation of the air-fuel two-phase flow field inside a centripetal pump was carried out using the VOF/Mixture model to investigate the effects of three relatively independent physical quantities, namely, fuel flow, outlet fuel discharge pressure, and rotational speed, on the operating characteristics of the centripetal pump. The flow law inside the flow channel of a centripetal pump was analyzed based on a rotating fluid pressure model, the free liquid surface radius of air-fuel, and the total pressure recovery coefficient. It was found that centripetal pumps have a steady working state and an unsteady working state. In a steady working state, the proportion of separated zones in the flow channel of the centripetal pump is small, the flow coefficient C of the flow channel is greater than 1, and the total pressure recovery coefficient of the centripetal pump is high. In an unsteady working state, the separation zone in the flow channel of the centripetal pump accounts for a large proportion, the flow channel flow coefficient C is less than 1, and the total pressure recovery coefficient of the centripetal pump is low. An unsteady working state can easily occur in small flow, high-speed conditions. By analyzing the working state and flow characteristics of the centripetal pump, the mechanism of the influence of the flow, outlet fuel discharge pressure, and rotational speed on the working state of the centripetal pump is revealed, which provides a basis for the stable operation of the centripetal pump.
Open AccessStudy on the Influence of Working Characteristics of Centripetal Pump Based on VOF/Mixture Model
Aviation fuel contamination can seriously affect aircraft flight safety, and the centripetal pump is the core component of aviation fuel purification equipment. The performance of centripetal pumps is highly demanded for purification equipment. The operating parameters of centripetal pumps significantly affect the internal flow characteristics, which affects the performance of centripetal pumps. However, the flow characteristics of a centripetal pump influenced by the operating parameters have not yet been elaborated upon. In this research, a three-dimensional numerical simulation of the air-fuel two-phase flow field inside a centripetal pump was carried out using the VOF/Mixture model to investigate the effects of three relatively independent physical quantities, namely, fuel flow, outlet fuel discharge pressure, and rotational speed, on the operating characteristics of the centripetal pump. The flow law inside the flow channel of a centripetal pump was analyzed based on a rotating fluid pressure model, the free liquid surface radius of air-fuel, and the total pressure recovery coefficient. It was found that centripetal pumps have a steady working state and an unsteady working state. In a steady working state, the proportion of separated zones in the flow channel of the centripetal pump is small, the flow coefficient C of the flow channel is greater than 1, and the total pressure recovery coefficient of the centripetal pump is high. In an unsteady working state, the separation zone in the flow channel of the centripetal pump accounts for a large proportion, the flow channel flow coefficient C is less than 1, and the total pressure recovery coefficient of the centripetal pump is low. An unsteady working state can easily occur in small flow, high-speed conditions. By analyzing the working state and flow characteristics of the centripetal pump, the mechanism of the influence of the flow, outlet fuel discharge pressure, and rotational speed on the working state of the centripetal pump is revealed, which provides a basis for the stable operation of the centripetal pump.
- 7 October 2022
- Published by Morressier GmbH
Developing an Integrated Technology-Environment-Economics Model to Simulate Food-Energy-Water Systems in Corn Belt Watersheds
To facilitate understanding and decision making in the food-energy-water (FEW) nexus context, we develop an integrated technology-environment-eco |
- 7 October 2022
- Published by Morressier GmbH
Developing an Integrated Technology-Environment-Economics Model to Simulate Food-Energy-Water Systems in Corn Belt Watersheds
To facilitate understanding and decision making in the food-energy-water (FEW) nexus context, we develop an integrated technology-environment-eco |
- 1 March 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 31 (2)
Unsteady Lift Model for Morphing Airfoil Based on Potential Flow Theory
This paper describes the study of unsteady forces acting on a two-dimensional morphing airfoil under the assumption of incompressible, inviscid flow. Through conformal mapping, the flow over a morphing airfoil was mapped to the flow over a movable, variable radius circle, and a mathematic analytic model of unsteady lift was derived. To verify the unsteady lift model, it was then simplified for the case of a thin airfoil whose camber changes with time, and numerical simulations were conducted for the flow over the deformable thin airfoil. The unsteady lift caused by airfoil deformation is equivalent to the quasisteady lift added to the corresponding additional unsteady lift. The additional unsteady lift is linearly correlated with the first time derivative and second time derivative of the airfoil surface displacement. When the airfoil surface undergoes a vibration with a large reduced frequency, the additional unsteady lift is mainly decided by the second time derivative of the surface displacement.
- 1 March 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 31 (2)
Unsteady Lift Model for Morphing Airfoil Based on Potential Flow Theory
This paper describes the study of unsteady forces acting on a two-dimensional morphing airfoil under the assumption of incompressible, inviscid flow. Through conformal mapping, the flow over a morphing airfoil was mapped to the flow over a movable, variable radius circle, and a mathematic analytic model of unsteady lift was derived. To verify the unsteady lift model, it was then simplified for the case of a thin airfoil whose camber changes with time, and numerical simulations were conducted for the flow over the deformable thin airfoil. The unsteady lift caused by airfoil deformation is equivalent to the quasisteady lift added to the corresponding additional unsteady lift. The additional unsteady lift is linearly correlated with the first time derivative and second time derivative of the airfoil surface displacement. When the airfoil surface undergoes a vibration with a large reduced frequency, the additional unsteady lift is mainly decided by the second time derivative of the surface displacement.
- 1 January 2016
- Published by Walter de Gruyter GmbH in International Journal of Turbo & Jet-Engines
- Vol. 33 (4) , 395-405
An Integrated Optimization Design Method Based on Surrogate Modeling Applied to Diverging Duct Design
This paper presents an integrated optimization design method in which uniform design, response surface methodology and genetic algorithm are used in combination. In detail, uniform design is used to select the experimental sampling points in the experimental domain and the system performance is evaluated by means of computational fluid dynamics to construct a database. After that, response surface methodology is employed to generate a surrogate mathematical model relating the optimization objective and the design variables. Subsequently, genetic algorithm is adopted and applied to the surrogate model to acquire the optimal solution in the case of satisfying some constraints. The method has been applied to the optimization design of an axisymmetric diverging duct, dealing with three design variables including one qualitative variable and two quantitative variables. The method of modeling and optimization design performs well in improving the duct aerodynamic performance and can be also applied to wider fields of mechanical design and seen as a useful tool for engineering designers, by reducing the design time and computation consumption.
- 1 January 2016
- Published by Walter de Gruyter GmbH in International Journal of Turbo & Jet-Engines
- Vol. 33 (4) , 395-405
An Integrated Optimization Design Method Based on Surrogate Modeling Applied to Diverging Duct Design
This paper presents an integrated optimization design method in which uniform design, response surface methodology and genetic algorithm are used in combination. In detail, uniform design is used to select the experimental sampling points in the experimental domain and the system performance is evaluated by means of computational fluid dynamics to construct a database. After that, response surface methodology is employed to generate a surrogate mathematical model relating the optimization objective and the design variables. Subsequently, genetic algorithm is adopted and applied to the surrogate model to acquire the optimal solution in the case of satisfying some constraints. The method has been applied to the optimization design of an axisymmetric diverging duct, dealing with three design variables including one qualitative variable and two quantitative variables. The method of modeling and optimization design performs well in improving the duct aerodynamic performance and can be also applied to wider fields of mechanical design and seen as a useful tool for engineering designers, by reducing the design time and computation consumption.
- 4 August 2015
- Published by ASME International in Journal of Fluids Engineering
- Vol. 137 (12) , 121101
Modeling the Effect of Stability Bleed on Back-Pressure in Mixed-Compression Supersonic Inlets
To stabilize the terminal normal shock on high-static pressure at outlet, called back-pressure , stability bleed slots are used in the throat of mixed-compression supersonic inlets. In this paper, a model for the functional relation between the bleed flow rate and back-pressure is established based on a bleed flow rate model (BFRM) in order to study the effect of stability bleed on the back-pressure in mixed-compression supersonic inlets. Given the inlet flow parameters , , and , the plenum pressure at slots' outlet, the terminal normal shock position in this model, the bleed flow rate , Mach number , and back-pressure were derived one by one from the basic laws of conservation. To study the effect of plenum pressure on subsonic flow of the divergent section behind the terminal normal shock, a correction coefficient is introduced to modify the Mach number . Furthermore, numerical simulations based on Reynolds-Averaged Navier–Stokes equations were performed to analyze the functional relation between the bleed flow rate and back-pressure . Computational fluid dynamics (CFD) results show that the present model agrees with the data.- 4 August 2015
- Published by ASME International in Journal of Fluids Engineering
- Vol. 137 (12) , 121101
Modeling the Effect of Stability Bleed on Back-Pressure in Mixed-Compression Supersonic Inlets
To stabilize the terminal normal shock on high-static pressure at outlet, called back-pressure , stability bleed slots are used in the throat of mixed-compression supersonic inlets. In this paper, a model for the functional relation between the bleed flow rate and back-pressure is established based on a bleed flow rate model (BFRM) in order to study the effect of stability bleed on the back-pressure in mixed-compression supersonic inlets. Given the inlet flow parameters , , and , the plenum pressure at slots' outlet, the terminal normal shock position in this model, the bleed flow rate , Mach number , and back-pressure were derived one by one from the basic laws of conservation. To study the effect of plenum pressure on subsonic flow of the divergent section behind the terminal normal shock, a correction coefficient is introduced to modify the Mach number . Furthermore, numerical simulations based on Reynolds-Averaged Navier–Stokes equations were performed to analyze the functional relation between the bleed flow rate and back-pressure . Computational fluid dynamics (CFD) results show that the present model agrees with the data.