Xuefeng Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xuefeng Xu has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Shuiquan Huang
School of Mechanical Engineering, Yanshan University, Qinhuangdao 066004, China
4 shared publications Tao Lv
3 shared publicationsMinghuan Wang
Zhejiang University of Technology
2 shared publications- Chao Gao
China Institute for Radiation Protection, Taiyuan, Shanxi, China
1 shared publication Fucai Liu
1 shared publication- Jian Wu
National Key Laboratory of Automotive Chassis Integration and Bionics, Jilin University, Changchun 130025, China
1 shared publication
Latest Publications
- Open Access
- 17 August 2022
- Published by Springer Nature in Research Square
A novel cold air electrostatic minimum quantity lubrication (CAEMQL) technique for machining of titanium alloys Ti-6Al-4V
Milling of titanium alloys is usually associated with a high cutting temperature and severe tool wear. Therefore, flood cooling technologies were conventionally employed for prolonging the tool life and improving the machined surface quality. However, a negative impact on the environment and waste disposal problems caused by a vast quantity of metalworking fluids used in the process has become significant. In this study, a new machining method called “cold air electrostatic minimum quantity lubrication (CAEMQL)” is proposed for machining titanium alloys Ti-6Al-4V. The milling performance of CAEMQL was systematically assessed in terms of cutting force, cutting temperature, surface roughness, tool life, tool wear and chip morphology, using minimum quantity lubrication (MQL), electrostatic minimum quantity lubrication (EMQL) and cold air minimum quantity lubrication (CAMQL) as benchmarks. It was found that CAEMQL resulted in an improved critical heat flux and steady-state heat transfer performance compared with MQL, EMQL and CAMQL, which thus produced a lower milling force, smaller milling temperature, better surface quality and less tool wear. The degrees of chip segmentation were enhanced with less deformation for CAEMQL due to its synergistic cooling and lubrication effect .
- 17 August 2022
- Published by Springer Nature in Research Square
Open AccessA novel cold air electrostatic minimum quantity lubrication (CAEMQL) technique for machining of titanium alloys Ti-6Al-4V
Milling of titanium alloys is usually associated with a high cutting temperature and severe tool wear. Therefore, flood cooling technologies were conventionally employed for prolonging the tool life and improving the machined surface quality. However, a negative impact on the environment and waste disposal problems caused by a vast quantity of metalworking fluids used in the process has become significant. In this study, a new machining method called “cold air electrostatic minimum quantity lubrication (CAEMQL)” is proposed for machining titanium alloys Ti-6Al-4V. The milling performance of CAEMQL was systematically assessed in terms of cutting force, cutting temperature, surface roughness, tool life, tool wear and chip morphology, using minimum quantity lubrication (MQL), electrostatic minimum quantity lubrication (EMQL) and cold air minimum quantity lubrication (CAMQL) as benchmarks. It was found that CAEMQL resulted in an improved critical heat flux and steady-state heat transfer performance compared with MQL, EMQL and CAMQL, which thus produced a lower milling force, smaller milling temperature, better surface quality and less tool wear. The degrees of chip segmentation were enhanced with less deformation for CAEMQL due to its synergistic cooling and lubrication effect .
- 9 February 2022
- Published by Wiley in Lubrication Science
- Vol. 34 (4) , 275-289
Tribological properties of water‐based nanofluids prepared by multi‐walled carbon nanotubes composites filled with sulfurised isobutylene
Sulfurised isobutylene (T321) was filled into the cavity of multi‐walled carbon nanotubes (MWCNTs) in order to synthesise MWCNT/T321 composites. Tribological properties of water‐based nanofluids with composites as additives were systematically investigated using a four‐ball configuration. The results showed that MWCNTs were filled by T321 with a filling rate of 22.5%. The nanofluids prepared by the composites produced a significantly lower coefficient of friction and wear loss, in comparison with the lubricants containing only MWCNTs or T321. Such improvement was attributed to the fact that during sliding the T321 filled into composites was released onto the rubbing surface to generate a lubricating film, resulting in a low resistance to shear, whilst the MWCNTs served as nano‐bearings on the formed lubricating film.
- 9 February 2022
- Published by Wiley in Lubrication Science
- Vol. 34 (4) , 275-289
Tribological properties of water‐based nanofluids prepared by multi‐walled carbon nanotubes composites filled with sulfurised isobutylene
Sulfurised isobutylene (T321) was filled into the cavity of multi‐walled carbon nanotubes (MWCNTs) in order to synthesise MWCNT/T321 composites. Tribological properties of water‐based nanofluids with composites as additives were systematically investigated using a four‐ball configuration. The results showed that MWCNTs were filled by T321 with a filling rate of 22.5%. The nanofluids prepared by the composites produced a significantly lower coefficient of friction and wear loss, in comparison with the lubricants containing only MWCNTs or T321. Such improvement was attributed to the fact that during sliding the T321 filled into composites was released onto the rubbing surface to generate a lubricating film, resulting in a low resistance to shear, whilst the MWCNTs served as nano‐bearings on the formed lubricating film.
- 15 August 2017
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 94 (1-4) , 655-666
Enhanced machining performance and lubrication mechanism of electrostatic minimum quantity lubrication-EMQL milling process
- 15 August 2017
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 94 (1-4) , 655-666
Enhanced machining performance and lubrication mechanism of electrostatic minimum quantity lubrication-EMQL milling process
- 10 July 2017
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 22 (2) , 271-286
Experimental evaluation on the effect of electrostatic minimum quantity lubrication (EMQL) in end milling of stainless steels
The machining of stainless steels is very challenging owing to their high toughness and low thermal conductivity, causing high cutting temperatures and rapid tool wear. Conventionally, metalworking fluids in flood form are used during the process to improve surface quality and tool life; however, their use raises issues including environmental pollution and economic concerns. Therefore, an electrostatic minimal quantity lubrication (EMQL) technology was developed to reduce the consumption of metalworking fluids. EMQL is a near-dry machining technology utilizing the synergetic effects between electrostatic spraying and minimum quantity lubrication (MQL), wherein the lubricant is to apply in a form of fine, uniform and highly penetrable and wettable mist droplets directly to the cutting zone. This study investigates the effect of EMQL in end milling of AISI 304 stainless steel in comparison with dry, wet and MQL machining. The results suggest that EMQL reduces tool wear and cutting force, prolongs tool life considerably and enhances surface finish compared with conventional wet and MQL machining. scanning electron microscopy and Energy-dispersive X-ray spectroscopy analyses show that EMQL considerably reduces adhesive and abrasive wear on the flank face because of the lower friction and heat generation resulting from more efficient entry of the lubricant into the cutting interfaces.
- 10 July 2017
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 22 (2) , 271-286
Experimental evaluation on the effect of electrostatic minimum quantity lubrication (EMQL) in end milling of stainless steels
The machining of stainless steels is very challenging owing to their high toughness and low thermal conductivity, causing high cutting temperatures and rapid tool wear. Conventionally, metalworking fluids in flood form are used during the process to improve surface quality and tool life; however, their use raises issues including environmental pollution and economic concerns. Therefore, an electrostatic minimal quantity lubrication (EMQL) technology was developed to reduce the consumption of metalworking fluids. EMQL is a near-dry machining technology utilizing the synergetic effects between electrostatic spraying and minimum quantity lubrication (MQL), wherein the lubricant is to apply in a form of fine, uniform and highly penetrable and wettable mist droplets directly to the cutting zone. This study investigates the effect of EMQL in end milling of AISI 304 stainless steel in comparison with dry, wet and MQL machining. The results suggest that EMQL reduces tool wear and cutting force, prolongs tool life considerably and enhances surface finish compared with conventional wet and MQL machining. scanning electron microscopy and Energy-dispersive X-ray spectroscopy analyses show that EMQL considerably reduces adhesive and abrasive wear on the flank face because of the lower friction and heat generation resulting from more efficient entry of the lubricant into the cutting interfaces.
- 21 June 2015
- Published by Springer Nature in Tribology Letters
- Vol. 59 (2) , 1-15
Tribological Performance and Lubrication Mechanism of Contact-Charged Electrostatic Spray Lubrication Technique
- 21 June 2015
- Published by Springer Nature in Tribology Letters
- Vol. 59 (2) , 1-15
Tribological Performance and Lubrication Mechanism of Contact-Charged Electrostatic Spray Lubrication Technique