Khaled H. Charif
Research Subjects
Khaled H. Charif has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
- Shadi Najjar
American University of Beirut
4 shared publications - Salah Sadek
Department of Civil and Environmental Engineering, American University of Beirut, Beirut, Lebanon
2 shared publications
Latest Publications
- 29 March 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 2697-2706
Comparative Study of Shear Modulus in Calcareous Sand and Sabkha Soils
The estimation of various soil moduli has always been a fundamental component of geotechnical engineering. Since most design works involve assessment of ground response to stress applications, an accurate estimate of the soil modulus is deemed imperative for computational geotechnics. Due to the non linearity of the stress-strain response of soils, the shear modulus is always a function of strain amplitude thus making the quantification of shear modulus critical when it comes to consideration of strain level induced by both loading scheme and soil properties. The comparison between the static and dynamic shear modulus as well as between various tools used to measure the shear modulus was rarely carried out on carbonate sands originating from marine sediments. This paper focuses on a comparison between small strain shear modulus (Go) measured using the down-hole seismic test (DH) and the seismic cone penetration test (SCPT) and estimated shear modulus (Go) obtained using available correlations with SPT and CPT. The comparison is conducted on unconventional soils comprised of Sabkha soils and cemented calcareous sands for a site in Abu Dhabi. The paper also compares the small-strain Go to the "high" strain G derived from cone penetration testing (CPT).
- 29 March 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 2697-2706
Comparative Study of Shear Modulus in Calcareous Sand and Sabkha Soils
The estimation of various soil moduli has always been a fundamental component of geotechnical engineering. Since most design works involve assessment of ground response to stress applications, an accurate estimate of the soil modulus is deemed imperative for computational geotechnics. Due to the non linearity of the stress-strain response of soils, the shear modulus is always a function of strain amplitude thus making the quantification of shear modulus critical when it comes to consideration of strain level induced by both loading scheme and soil properties. The comparison between the static and dynamic shear modulus as well as between various tools used to measure the shear modulus was rarely carried out on carbonate sands originating from marine sediments. This paper focuses on a comparison between small strain shear modulus (Go) measured using the down-hole seismic test (DH) and the seismic cone penetration test (SCPT) and estimated shear modulus (Go) obtained using available correlations with SPT and CPT. The comparison is conducted on unconventional soils comprised of Sabkha soils and cemented calcareous sands for a site in Abu Dhabi. The paper also compares the small-strain Go to the "high" strain G derived from cone penetration testing (CPT).
- 29 March 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 2922-2931
Impact of Spatial Variability on the Design of Drilled Shafts in Weak Carbonate Rocks
This paper provides a framework for studying the combined effect of model uncertainties and uncertainties due to spatial variability on the side friction and end bearing of drilled shafts in weak carbonate rocks. Reliability assessments using Monte Carlo simulations indicated that the tip resistance could play a role in increasing the reliability index of a shaft if incorporated in design. The effect of the tip resistance is higher when for shafts with larger diameters and shorter lengths. For designs where the end bearing is ignored, model uncertainties and uncertainties due to spatial variability result in reliability indices between 2.0 and 2.4. These reliability indices increase to 2.5 and 3.5 when end bearing is included in the analysis.
- 29 March 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 2922-2931
Impact of Spatial Variability on the Design of Drilled Shafts in Weak Carbonate Rocks
This paper provides a framework for studying the combined effect of model uncertainties and uncertainties due to spatial variability on the side friction and end bearing of drilled shafts in weak carbonate rocks. Reliability assessments using Monte Carlo simulations indicated that the tip resistance could play a role in increasing the reliability index of a shaft if incorporated in design. The effect of the tip resistance is higher when for shafts with larger diameters and shorter lengths. For designs where the end bearing is ignored, model uncertainties and uncertainties due to spatial variability result in reliability indices between 2.0 and 2.4. These reliability indices increase to 2.5 and 3.5 when end bearing is included in the analysis.
- 21 June 2011
- Published by American Society of Civil Engineers (ASCE)
- p. 395-402
Effect of Spatial Variability and Model Uncertainty on the Design of Sockets in Weak Carbonate Rocks
This paper provides a framework for studying the combined effect of model uncertainties and uncertainties due to spatial variability on the side friction of drilled shafts in weak carbonate rocks. High quality site investigation data for a site in Dubai-UAE is used to characterize the spatial variability of weak carbonate rocks. Reliability assessments using Monte Carlo simulations indicated that uncertainty due to spatial variability has a notable effect on the reliability index with the effect being related to the pile length. In addition, the calculated reliability indices were found to be strongly affected by whether the median or the 10th percentile UCS value was used in the deterministic design.
- 21 June 2011
- Published by American Society of Civil Engineers (ASCE)
- p. 395-402
Effect of Spatial Variability and Model Uncertainty on the Design of Sockets in Weak Carbonate Rocks
This paper provides a framework for studying the combined effect of model uncertainties and uncertainties due to spatial variability on the side friction of drilled shafts in weak carbonate rocks. High quality site investigation data for a site in Dubai-UAE is used to characterize the spatial variability of weak carbonate rocks. Reliability assessments using Monte Carlo simulations indicated that uncertainty due to spatial variability has a notable effect on the reliability index with the effect being related to the pile length. In addition, the calculated reliability indices were found to be strongly affected by whether the median or the 10th percentile UCS value was used in the deterministic design.
- 18 February 2010
- Published by American Society of Civil Engineers (ASCE)
- p. 190-205
Side Friction along Drilled Shafts in Weak Carbonate Rocks
Weak carbonate rocks are characterized by shear strength and deformation properties that are inferior to those of conventional rocks but superior to those of stiff or dense soils. Although numerous research programs have been carried out on almost all types of piles in various soil profiles, the behavior of drilled shafts in weak carbonate rocks has not been thoroughly investigated. In this paper, an attempt is made to enhance the design practice for drilled shafts in weak carbonate rocks by integrating the results of full-scale static instrumented pile load tests on large-diameter drilled shafts with good quality rock properties derived from reliable geotechnical investigations. The objective of the test program is to investigate the effect of several parameters which are known to influence rock-pile interaction and skin friction mobilization. Observations of the t-z behavior of the tested piles indicate a strong correlation between the normalized skin friction t/tmax and the normalized vertical displacement along the shaft z/zmax. More importantly, results indicated that the maximum mobilized side friction tmax was found to increase with increasing rock modulus and/or decreasing pile diameter thus confirming the possible effect of the constant normal stiffness on load transfer. The predictive performance of six commonly used empirical models which are based on the unconfined compressive strength was investigated. Results indicated that all models except those proposed by Horvath and Kenney (1979) and O'Neill and Reese (1999) tend to significantly overestimate side shear. A simple proposed empirical model that combines the effect of the unconfined compressive strength and the constant normal stiffness showed a better performance when compared to all other models tested in this study.
- 18 February 2010
- Published by American Society of Civil Engineers (ASCE)
- p. 190-205
Side Friction along Drilled Shafts in Weak Carbonate Rocks
Weak carbonate rocks are characterized by shear strength and deformation properties that are inferior to those of conventional rocks but superior to those of stiff or dense soils. Although numerous research programs have been carried out on almost all types of piles in various soil profiles, the behavior of drilled shafts in weak carbonate rocks has not been thoroughly investigated. In this paper, an attempt is made to enhance the design practice for drilled shafts in weak carbonate rocks by integrating the results of full-scale static instrumented pile load tests on large-diameter drilled shafts with good quality rock properties derived from reliable geotechnical investigations. The objective of the test program is to investigate the effect of several parameters which are known to influence rock-pile interaction and skin friction mobilization. Observations of the t-z behavior of the tested piles indicate a strong correlation between the normalized skin friction t/tmax and the normalized vertical displacement along the shaft z/zmax. More importantly, results indicated that the maximum mobilized side friction tmax was found to increase with increasing rock modulus and/or decreasing pile diameter thus confirming the possible effect of the constant normal stiffness on load transfer. The predictive performance of six commonly used empirical models which are based on the unconfined compressive strength was investigated. Results indicated that all models except those proposed by Horvath and Kenney (1979) and O'Neill and Reese (1999) tend to significantly overestimate side shear. A simple proposed empirical model that combines the effect of the unconfined compressive strength and the constant normal stiffness showed a better performance when compared to all other models tested in this study.