Justin Weber
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Justin Weber has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Ronald W. Breault
National Energy Technology Laboratory
5 shared publications - Steven Rowan
NETL
3 shared publications - Andrew C. Nix
Department of Mechanical and Aerospace Engineering, West Virginia University, Morgantown, WV 26506, USA
2 shared publications - Chien-Shing Lee
Purdue University School of Aeronautics and Astronautics West Layfayette, IN 47907
2 shared publications - Donald H. Ferguson
National Energy Technology Laboratory, Morgantown, WV 26507
2 shared publications - Douglas Straub
National Energy Technology Laboratory, 3610 Collins Ferry Road, Morgantown, WV 26507
2 shared publications
Latest Publications
- 1 September 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Propulsion and Power
- Vol. 40 (5) , 701-716
Limit Cycle Oscillating Detonation Wave Behavior Analysis Within a Rotating Detonation Engine
- 1 September 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Propulsion and Power
- Vol. 40 (5) , 701-716
Limit Cycle Oscillating Detonation Wave Behavior Analysis Within a Rotating Detonation Engine
- 16 January 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (5) , 1-39
Effects of Downstream Vortex Generators on Film Cooling a Flat Plate Fed by Crossflow
Counter-rotating vortices, formed by the interaction of film-cooling jets and the hot gas flow, adversely affect the performance of conventional film-cooling designs. Downstream vortex generators have been shown to improve cooling effectiveness by mitigating the effects of the counter-rotating vortices and by deflecting the cooling jet laterally. In this study, computational and experimental methods were used to examine how cylindrical film-cooling holes (D = 3.2 mm, L/D = 6, p/D = 3, α = 30 deg) with and without downstream vortex generators perform when the coolant supply channel is perpendicular to the direction of the hot gas. For this study, the hot gas had a temperature of 650 K and an average Mach number of 0.23. The hot-gas-to-coolant temperature ratio was 1.9, and two blowing ratios (0.75 and 1.0) were studied. Results from the computational fluid dynamics study show how crossflow affects the interaction between the film-cooling jet and hot gas flow with and without downstream vortex generators. The experimental measurements were based on infrared thermography in a conjugate heat transfer environment. Results were obtained for film-cooling performance in terms of overall effectiveness, film effectiveness, and local heat transfer coefficients. The downstream vortex generators can increase the laterally averaged effectiveness by a factor of 1.5 relative to cylindrical holes, but this higher performance is restricted to low crossflow velocities and higher blowing ratios.
- 16 January 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 146 (5) , 1-39
Effects of Downstream Vortex Generators on Film Cooling a Flat Plate Fed by Crossflow
Counter-rotating vortices, formed by the interaction of film-cooling jets and the hot gas flow, adversely affect the performance of conventional film-cooling designs. Downstream vortex generators have been shown to improve cooling effectiveness by mitigating the effects of the counter-rotating vortices and by deflecting the cooling jet laterally. In this study, computational and experimental methods were used to examine how cylindrical film-cooling holes (D = 3.2 mm, L/D = 6, p/D = 3, α = 30 deg) with and without downstream vortex generators perform when the coolant supply channel is perpendicular to the direction of the hot gas. For this study, the hot gas had a temperature of 650 K and an average Mach number of 0.23. The hot-gas-to-coolant temperature ratio was 1.9, and two blowing ratios (0.75 and 1.0) were studied. Results from the computational fluid dynamics study show how crossflow affects the interaction between the film-cooling jet and hot gas flow with and without downstream vortex generators. The experimental measurements were based on infrared thermography in a conjugate heat transfer environment. Results were obtained for film-cooling performance in terms of overall effectiveness, film effectiveness, and local heat transfer coefficients. The downstream vortex generators can increase the laterally averaged effectiveness by a factor of 1.5 relative to cylindrical holes, but this higher performance is restricted to low crossflow velocities and higher blowing ratios.
- 14 September 2023
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 145 (11) , 1-12
Consideration of Nonideal Detonation Regimes Influenced by Wave Modes in a Water-Cooled Rotating Detonation Engine Using OH* Chemiluminescence
Although inherently unstable, existing research in rotating detonation combustion supports its application in notionally steady processes resulting in greater availability compared to conventional, constant pressure combustion. Further improvements rely on a more in-depth understanding of system losses and identifying conditions which optimize device performance. Within this study, the presence and proportion of ideal and nonideal combustion regimes are compared across a variety of process conditions and wave modes. Large-scale data analysis seeks to summarize proportional heat release associated with commensal, parasitic, and detonative combustion averaged across individual traces of OH* chemiluminescent data acquired at the detonation plane. Means of regime partitioning based on the anatomy of the time-resolved OH* signal are proposed to ensure consistent analysis throughout the current and future studies concerning combustion regimes. Of particular interest is the possible influence of wave on the nonideal combustion in relative proportion to the desired detonation. Results showed improved percent detonation with increasing significance for the following trends: decreasing equivalence ratio, increasing wave count, decreasing wave velocity, and increasing detonation time. Increased wave number, brought on by decreased equivalence ratios and wave velocities, is thought to decrease fill region surface area, and therefore, decrease nonideal contact burning. Additional analysis is performed to consider possible trend variation due to the presence of stable galloping waves, which were found to have minimal influence on relative percent detonation values. The outcome of this study suggests operational states, which correspond to increased wave quantities for increased proportions of reactants consumed by the targeted detonative combustion regime.
- 14 September 2023
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 145 (11) , 1-12
Consideration of Nonideal Detonation Regimes Influenced by Wave Modes in a Water-Cooled Rotating Detonation Engine Using OH* Chemiluminescence
Although inherently unstable, existing research in rotating detonation combustion supports its application in notionally steady processes resulting in greater availability compared to conventional, constant pressure combustion. Further improvements rely on a more in-depth understanding of system losses and identifying conditions which optimize device performance. Within this study, the presence and proportion of ideal and nonideal combustion regimes are compared across a variety of process conditions and wave modes. Large-scale data analysis seeks to summarize proportional heat release associated with commensal, parasitic, and detonative combustion averaged across individual traces of OH* chemiluminescent data acquired at the detonation plane. Means of regime partitioning based on the anatomy of the time-resolved OH* signal are proposed to ensure consistent analysis throughout the current and future studies concerning combustion regimes. Of particular interest is the possible influence of wave on the nonideal combustion in relative proportion to the desired detonation. Results showed improved percent detonation with increasing significance for the following trends: decreasing equivalence ratio, increasing wave count, decreasing wave velocity, and increasing detonation time. Increased wave number, brought on by decreased equivalence ratios and wave velocities, is thought to decrease fill region surface area, and therefore, decrease nonideal contact burning. Additional analysis is performed to consider possible trend variation due to the presence of stable galloping waves, which were found to have minimal influence on relative percent detonation values. The outcome of this study suggests operational states, which correspond to increased wave quantities for increased proportions of reactants consumed by the targeted detonative combustion regime.
- 12 October 2022
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (2)
Computational and Experimental Study of Film-Cooling Effectiveness With and Without Downstream Vortex Generators
Downstream vortex generators that involve a pair of rectangular plates arranged in an open V-shape placed just downstream of each film-cooling hole were shown to create flow and vortical structures that entrain lifted film-cooling flow back to the surface and increase its lateral spreading on the surface (GT2020–14317). In this study, computations and measurements were performed to examine the flow mechanisms this vortex generator induces to improve film-cooling effectiveness of a flat plate with the cooling flow emanating from one row of inclined holes. Parameters studied include blowing ratio (BR = 0.75 and 1.0) and temperature ratio (TR = 1.07 and 1.9). The computational study is based on steady Reynolds-averaged Navier–Stokes (RANS) closed by the shear-stress transport (SST) turbulence model with and without conjugate analysis. The experimental study was conducted by using a conjugate heat transfer test rig with a plenum, where cooling flow is introduced. Measurements made include velocity and temperature profiles upstream and downstream of the film-cooling holes as well as the temperature at several locations on the hot and cold sides of the film-cooled flat plate. The computational study was validated by comparing computed results with those from measurements at BR = 0.75 and 1.0 and TR = 1.9. Computational and experimental results are presented to show the effects of BR and TR on the flow structures and how those structures improve the effectiveness of film cooling with and without the downstream vortex generators and with and without conjugate heat transfer.
- 12 October 2022
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (2)
Computational and Experimental Study of Film-Cooling Effectiveness With and Without Downstream Vortex Generators
Downstream vortex generators that involve a pair of rectangular plates arranged in an open V-shape placed just downstream of each film-cooling hole were shown to create flow and vortical structures that entrain lifted film-cooling flow back to the surface and increase its lateral spreading on the surface (GT2020–14317). In this study, computations and measurements were performed to examine the flow mechanisms this vortex generator induces to improve film-cooling effectiveness of a flat plate with the cooling flow emanating from one row of inclined holes. Parameters studied include blowing ratio (BR = 0.75 and 1.0) and temperature ratio (TR = 1.07 and 1.9). The computational study is based on steady Reynolds-averaged Navier–Stokes (RANS) closed by the shear-stress transport (SST) turbulence model with and without conjugate analysis. The experimental study was conducted by using a conjugate heat transfer test rig with a plenum, where cooling flow is introduced. Measurements made include velocity and temperature profiles upstream and downstream of the film-cooling holes as well as the temperature at several locations on the hot and cold sides of the film-cooled flat plate. The computational study was validated by comparing computed results with those from measurements at BR = 0.75 and 1.0 and TR = 1.9. Computational and experimental results are presented to show the effects of BR and TR on the flow structures and how those structures improve the effectiveness of film cooling with and without the downstream vortex generators and with and without conjugate heat transfer.
- Open Access
Saturation Carrying Capacity for Group A Particles in a Circulating Fluidized Bed
Empirical models continue to play a significant role in the design process of multiphase chemical reactors, particularly riser reactors in circulating fluidized bed (CFB) processes. It is imperative that accurate, industrial relevant correlations are developed to aid these design efforts. Using poor correlations could result in startup issues and significant redesign work. In this work, a new correlation is proposed to predict the saturation carrying capacity of Geldart Group A particles. This new correlation improves upon the currently available correlations for these materials and covers a broad range of Geldart Group A particles (particle diameters from 52 to 70 µm, and Archimedes numbers ranging from 5 to 20), superficial gas velocities (1 to 4 m/s), and riser diameters (0.066 to 0.3048 m). The new correlation has an Absolute Average Percent Deviation of only 17.6%, making it the most accurate correlation for Geldart Group A particles in the current literature.
Open AccessSaturation Carrying Capacity for Group A Particles in a Circulating Fluidized Bed
Empirical models continue to play a significant role in the design process of multiphase chemical reactors, particularly riser reactors in circulating fluidized bed (CFB) processes. It is imperative that accurate, industrial relevant correlations are developed to aid these design efforts. Using poor correlations could result in startup issues and significant redesign work. In this work, a new correlation is proposed to predict the saturation carrying capacity of Geldart Group A particles. This new correlation improves upon the currently available correlations for these materials and covers a broad range of Geldart Group A particles (particle diameters from 52 to 70 µm, and Archimedes numbers ranging from 5 to 20), superficial gas velocities (1 to 4 m/s), and riser diameters (0.066 to 0.3048 m). The new correlation has an Absolute Average Percent Deviation of only 17.6%, making it the most accurate correlation for Geldart Group A particles in the current literature.
- 13 March 2020
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 142 (7) , 1-26
Process Failure Detection via Recurrence Quantification Analysis in a Slot-Rectangular Spouted Bed
A study was conducted to explore the applicability of recurrence and recurrence quantification analysis (RQA) to the detection of process failures in spouted bed reactor systems. Three different potential failure modes were examined in a transparent, cold flow slot-rectangular spouted bed. These being, a simulated air leak from a side wall of the reactor, a simulated gas leak from the top wall of the reactor, and simulated agglomeration of solids via introduction of larger “klinker” particles. Bed pressure drop time history data were collected and analyzed via generation of recurrence plots (RPs) and RQA parameters. In general, the simulated agglomeration case was quite easily detected via ever RQA Parameter examined, whereas the simulated air leaks were detected by only a single RQA parameter.
- 13 March 2020
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 142 (7) , 1-26
Process Failure Detection via Recurrence Quantification Analysis in a Slot-Rectangular Spouted Bed
A study was conducted to explore the applicability of recurrence and recurrence quantification analysis (RQA) to the detection of process failures in spouted bed reactor systems. Three different potential failure modes were examined in a transparent, cold flow slot-rectangular spouted bed. These being, a simulated air leak from a side wall of the reactor, a simulated gas leak from the top wall of the reactor, and simulated agglomeration of solids via introduction of larger “klinker” particles. Bed pressure drop time history data were collected and analyzed via generation of recurrence plots (RPs) and RQA parameters. In general, the simulated agglomeration case was quite easily detected via ever RQA Parameter examined, whereas the simulated air leaks were detected by only a single RQA parameter.
- 28 February 2020
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 142 (7) , 1-26
Effects of Riser Diameter on Solids Holdup and Particle Velocity Profiles in Circulating Fluidized Bed Riser Systems
Tests were performed in a 0.1-m diameter small circulating fluidized bed (SCFB) and 0.3 m diameter cold flow circulating fluidized bed (CFCFB) riser systems located at the National Energy Technology Laboratory (NETL) to study the effects of riser diameter on the riser hydrodynamics. These tests were performed at solids circulation rates of Gs = 20 and 75 kg/m2 s and superficial gas velocities of Ug = 5.8 and 6.5 m/s using high-density polyethylene (HDPE) pellets with a density of 0.863 g/cm3, particle size range of 600–1400 µm (with a Sauter mean diameter of 871 µm, placing them in the Geldart B classification). Comparisons of riser axial pressure and solids fraction profiles, radial particle velocity profiles, and radial profiles of higher statistical moments and select chaos analysis parameters were considered. The results showed that for a given Ug and Gs, the smaller diameter riser exhibited characteristics associated with more dilute solids flow than that observed in the larger diameter riser. Additionally, the larger diameter riser exhibited a downward flow of solids near the wall under all test conditions, whereas the smaller diameter riser data exhibited little or no indications of solids downflow near the wall. These findings suggest that, from an industrial standpoint, a direct scaleup of small-scale tests cannot readily be accomplished as the solids holdup and the solids velocity profiles in small units (those normally tested in the laboratory) are not similar to those of large units and the performance of large units can therefore not be predicted from small-scale tests.
- 28 February 2020
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 142 (7) , 1-26
Effects of Riser Diameter on Solids Holdup and Particle Velocity Profiles in Circulating Fluidized Bed Riser Systems
Tests were performed in a 0.1-m diameter small circulating fluidized bed (SCFB) and 0.3 m diameter cold flow circulating fluidized bed (CFCFB) riser systems located at the National Energy Technology Laboratory (NETL) to study the effects of riser diameter on the riser hydrodynamics. These tests were performed at solids circulation rates of Gs = 20 and 75 kg/m2 s and superficial gas velocities of Ug = 5.8 and 6.5 m/s using high-density polyethylene (HDPE) pellets with a density of 0.863 g/cm3, particle size range of 600–1400 µm (with a Sauter mean diameter of 871 µm, placing them in the Geldart B classification). Comparisons of riser axial pressure and solids fraction profiles, radial particle velocity profiles, and radial profiles of higher statistical moments and select chaos analysis parameters were considered. The results showed that for a given Ug and Gs, the smaller diameter riser exhibited characteristics associated with more dilute solids flow than that observed in the larger diameter riser. Additionally, the larger diameter riser exhibited a downward flow of solids near the wall under all test conditions, whereas the smaller diameter riser data exhibited little or no indications of solids downflow near the wall. These findings suggest that, from an industrial standpoint, a direct scaleup of small-scale tests cannot readily be accomplished as the solids holdup and the solids velocity profiles in small units (those normally tested in the laboratory) are not similar to those of large units and the performance of large units can therefore not be predicted from small-scale tests.
- 4 February 2020
- Published by ASME International in Journal of Fluids Engineering
- Vol. 142 (3)
Optimization of a Cyclone Using Multiphase Flow Computational Fluid Dynamics
The U.S. Department of Energy National Energy Technology Laboratory's (NETL) 50 kWth chemical looping reactor (CLR) has an underperforming cyclone, which was designed using empirical correlations. To improve the performance of this cyclone using computational fluid dynamics (CFD)-based modeling simulations, four critical design parameters including the vortex tube radius and length, barrel radius, and the inlet width and height were optimized. NETL's open source multiphase flow with interphase exchange (MFiX) CFD code has been used to model a series of cyclones by systematically varying the geometric design parameters. To perform the optimization process, the surrogate modeling and sensitivity analysis followed by the optimization capability in nodeworks was used. The basic methodology for the process is to employ a statistical design of experiments (DOE) method to generate sampling simulations that fill the design space. Corresponding CFD models are then created, executed, and postprocessed. A response surface is created to characterize the relationship between input parameters and the quantities of interest (QoI). Finally, the CFD-surrogate is used by an optimization method to find the optimal design condition based on the objective and constraints prescribed. The resulting optimal cyclone has a larger diameter and longer vortex tube, a larger diameter barrel, and a taller and narrower solids inlet. The improved design has a predicted pressure drop 11 times lower than the original design while reducing the mass loss by a factor of 2.3.
- 4 February 2020
- Published by ASME International in Journal of Fluids Engineering
- Vol. 142 (3)
Optimization of a Cyclone Using Multiphase Flow Computational Fluid Dynamics
The U.S. Department of Energy National Energy Technology Laboratory's (NETL) 50 kWth chemical looping reactor (CLR) has an underperforming cyclone, which was designed using empirical correlations. To improve the performance of this cyclone using computational fluid dynamics (CFD)-based modeling simulations, four critical design parameters including the vortex tube radius and length, barrel radius, and the inlet width and height were optimized. NETL's open source multiphase flow with interphase exchange (MFiX) CFD code has been used to model a series of cyclones by systematically varying the geometric design parameters. To perform the optimization process, the surrogate modeling and sensitivity analysis followed by the optimization capability in nodeworks was used. The basic methodology for the process is to employ a statistical design of experiments (DOE) method to generate sampling simulations that fill the design space. Corresponding CFD models are then created, executed, and postprocessed. A response surface is created to characterize the relationship between input parameters and the quantities of interest (QoI). Finally, the CFD-surrogate is used by an optimization method to find the optimal design condition based on the objective and constraints prescribed. The resulting optimal cyclone has a larger diameter and longer vortex tube, a larger diameter barrel, and a taller and narrower solids inlet. The improved design has a predicted pressure drop 11 times lower than the original design while reducing the mass loss by a factor of 2.3.
- 29 March 2018
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 140 (6)
Analysis of a Vortexing Circulating Fluidized Bed for Process Intensification Via High-G Flows
Fluidized beds are used in many industries where gas–solid reactions are present for their favorable characteristics of good solids mixing, high heat, and mass transfer rates, and large throughputs. In an attempt to increase throughput, reduce reactor footprints, and reduce costs, process intensification by unconventional reactor designs is being pursued. Specifically, this work focuses on the development of high-G reactors where the particles are experiencing a centripetal force typically on the order of ten times the force of gravity. This operating regime provides intensified gas–solids contact providing higher mass transfer, heat transfer, and gas throughput than a typical fluidized bed. This work focuses analysis of a cold flow vortexing circulating fluidized bed (CFB). Through mapping the pressure distributions in the riser, insights into the behavior of the system were made and compared to CPFD Barracuda computational fluid dynamic models. The simulation results outlined the working envelope of the system and provided a baseline to compare the experimental results. The experimental pressure data determined angular velocities of the gas in the range of 30–40 m/s, with corresponding particle velocities around 15 m/s.
- 29 March 2018
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 140 (6)
Analysis of a Vortexing Circulating Fluidized Bed for Process Intensification Via High-G Flows
Fluidized beds are used in many industries where gas–solid reactions are present for their favorable characteristics of good solids mixing, high heat, and mass transfer rates, and large throughputs. In an attempt to increase throughput, reduce reactor footprints, and reduce costs, process intensification by unconventional reactor designs is being pursued. Specifically, this work focuses on the development of high-G reactors where the particles are experiencing a centripetal force typically on the order of ten times the force of gravity. This operating regime provides intensified gas–solids contact providing higher mass transfer, heat transfer, and gas throughput than a typical fluidized bed. This work focuses analysis of a cold flow vortexing circulating fluidized bed (CFB). Through mapping the pressure distributions in the riser, insights into the behavior of the system were made and compared to CPFD Barracuda computational fluid dynamic models. The simulation results outlined the working envelope of the system and provided a baseline to compare the experimental results. The experimental pressure data determined angular velocities of the gas in the range of 30–40 m/s, with corresponding particle velocities around 15 m/s.
- Open Access
Chemical Looping Combustion of Hematite Ore with Methane and Steam in a Fluidized Bed Reactor
Chemical looping combustion is considered an indirect method of oxidizing a carbonaceous fuel, utilizing a metal oxide oxygen carrier to provide oxygen to the fuel. The advantage is the significantly reduced energy penalty for separating out the CO2 for reuse or sequestration in a carbon-constrained world. One of the major issues with chemical looping combustion is the cost of the oxygen carrier. Hematite ore is a proposed oxygen carrier due to its high strength and resistance to mechanical attrition, but its reactivity is rather poor compared to tailored oxygen carriers. This problem is further exacerbated by methane cracking, the subsequent deposition of carbon and the inability to transfer oxygen at a sufficient rate from the core of the particle to the surface for fuel conversion to CO2. Oxygen needs to be readily available at the surface to prevent methane cracking. The purpose of this work was to demonstrate the use of steam to overcome this issue and improve the conversion of the natural gas to CO2, as well as to provide data for computational fluid dynamics (CFD) validation. The steam will gasify the deposited carbon to promote the methane conversion. This work studies the performance of hematite ore with methane and steam mixtures in a 5 cm fluidized bed up to approximately 140 kPa. Results show an increased conversion of methane in the presence of steam (from 20–45% without steam to 60–95%) up to a certain point, where performance decreases. Adding steam allows the methane conversion to carbon dioxide to be similar to the overall methane conversion; it also helped to prevent carbon accumulation from occurring on the particle. In general, the addition of steam to the feed gas increased the methane conversion. Furthermore, the addition of steam caused the steam methane reforming reaction to form more hydrogen and carbon monoxide at higher steam and methane concentrations, which was not completely converted at higher concentrations and at these residence times.
Open AccessChemical Looping Combustion of Hematite Ore with Methane and Steam in a Fluidized Bed Reactor
Chemical looping combustion is considered an indirect method of oxidizing a carbonaceous fuel, utilizing a metal oxide oxygen carrier to provide oxygen to the fuel. The advantage is the significantly reduced energy penalty for separating out the CO2 for reuse or sequestration in a carbon-constrained world. One of the major issues with chemical looping combustion is the cost of the oxygen carrier. Hematite ore is a proposed oxygen carrier due to its high strength and resistance to mechanical attrition, but its reactivity is rather poor compared to tailored oxygen carriers. This problem is further exacerbated by methane cracking, the subsequent deposition of carbon and the inability to transfer oxygen at a sufficient rate from the core of the particle to the surface for fuel conversion to CO2. Oxygen needs to be readily available at the surface to prevent methane cracking. The purpose of this work was to demonstrate the use of steam to overcome this issue and improve the conversion of the natural gas to CO2, as well as to provide data for computational fluid dynamics (CFD) validation. The steam will gasify the deposited carbon to promote the methane conversion. This work studies the performance of hematite ore with methane and steam mixtures in a 5 cm fluidized bed up to approximately 140 kPa. Results show an increased conversion of methane in the presence of steam (from 20–45% without steam to 60–95%) up to a certain point, where performance decreases. Adding steam allows the methane conversion to carbon dioxide to be similar to the overall methane conversion; it also helped to prevent carbon accumulation from occurring on the particle. In general, the addition of steam to the feed gas increased the methane conversion. Furthermore, the addition of steam caused the steam methane reforming reaction to form more hydrogen and carbon monoxide at higher steam and methane concentrations, which was not completely converted at higher concentrations and at these residence times.