Mingming Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mingming Zhang has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Chang Cai
Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing, China
2 shared publicationsJianzhong Xu
Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing 100190, China
2 shared publicationsZiliang Zhang
2 shared publicationsBin Tan
Chinese Academy of Sciences
1 shared publicationC. Cai
Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing, China
1 shared publicationHuijing Cao
Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing, China
1 shared publication
Latest Publications
- Open Access
The Effects of Core Machining Configurations on the Mechanical Properties of Cores and Sandwich Structures
Composite sandwich structures are widely used in the fields of aviation, marine, and energy due to their high specific stiffness and design flexibility. Improving the mechanical properties of the cores is significant to the strength, modulus, and stability of composite sandwich structures. Two kinds of core machining configurations were designed by combining thin grooves, perforated holes, and thick contour cuts as well as non-machining plain cores. The cores and sandwich structures with these configurations were fabricated using a vacuum-assistant infusion process. Static tensile, compressive, shear, and peeling tests were conducted on the infused cores and sandwich structures. The results showed that the tensile, compressive, and shear moduli, and compressive strength of the infused cores can be greatly improved. The tensile strength changed negligibly due to stress concentration induced by irregular foam cell and the shear-lag phenomenon of the resin column/foam interface. The shear strength of the infused cores increased slightly. The thick contour cuts and perforated holes can greatly improve the face sheet/core peel capacity of the sandwich structures, whereas the thin grooves can moderately improve the peel capacity. Both infused cores with the designed machining configurations exhibited positive effects on the compressive, tensile, and shear moduli, and compressive strength, considering the material costs. The study provides a comprehensive and quantitative insight into the effects of core machining configurations on mechanical properties of infused cores and composite sandwich structures.
Open AccessThe Effects of Core Machining Configurations on the Mechanical Properties of Cores and Sandwich Structures
Composite sandwich structures are widely used in the fields of aviation, marine, and energy due to their high specific stiffness and design flexibility. Improving the mechanical properties of the cores is significant to the strength, modulus, and stability of composite sandwich structures. Two kinds of core machining configurations were designed by combining thin grooves, perforated holes, and thick contour cuts as well as non-machining plain cores. The cores and sandwich structures with these configurations were fabricated using a vacuum-assistant infusion process. Static tensile, compressive, shear, and peeling tests were conducted on the infused cores and sandwich structures. The results showed that the tensile, compressive, and shear moduli, and compressive strength of the infused cores can be greatly improved. The tensile strength changed negligibly due to stress concentration induced by irregular foam cell and the shear-lag phenomenon of the resin column/foam interface. The shear strength of the infused cores increased slightly. The thick contour cuts and perforated holes can greatly improve the face sheet/core peel capacity of the sandwich structures, whereas the thin grooves can moderately improve the peel capacity. Both infused cores with the designed machining configurations exhibited positive effects on the compressive, tensile, and shear moduli, and compressive strength, considering the material costs. The study provides a comprehensive and quantitative insight into the effects of core machining configurations on mechanical properties of infused cores and composite sandwich structures.
- 13 April 2021
- Published by Springer Nature in Journal of Thermal Science
- Vol. 30 (3) , 743-757
A Review on Modeling of Bionic Flow Control Methods for Large-Scale Wind Turbine Blades
- 13 April 2021
- Published by Springer Nature in Journal of Thermal Science
- Vol. 30 (3) , 743-757
A Review on Modeling of Bionic Flow Control Methods for Large-Scale Wind Turbine Blades
- 7 May 2020
- Published by Taylor & Francis in International Journal of Computational Fluid Dynamics
- Vol. 34 (5) , 333-345
A general model for riblets simulation in turbulent flows
The shark-skin-inspired riblets could effectively reduce the turbulence wall-skin friction compared with the smooth surface. Nevertheless, computations of the flow field over riblets in the practical configurations (e.g., airplanes and wind turbines) remain unfeasible for its huge computational cost. In this study, a general strategy for modelling the effects of riblets in turbulent flows is proposed. Riblets are modelled by adopting a slip-boundary condition on the smooth wall. A quantitative relationship between the riblet geometric parameters and the slip length is theoretically built for the first time. This modelling method could greatly reduce grid numbers in the validating procedure by using Large-Eddy Simulation, and the modelling results indicate that the flow fields in logarithmic and wake regions over riblets could be accurately reproduced. Additionally, considering the slip-boundary model is not capable of reproducing the near-wall flow, a simplified calculating method is developed.
- 7 May 2020
- Published by Taylor & Francis in International Journal of Computational Fluid Dynamics
- Vol. 34 (5) , 333-345
A general model for riblets simulation in turbulent flows
The shark-skin-inspired riblets could effectively reduce the turbulence wall-skin friction compared with the smooth surface. Nevertheless, computations of the flow field over riblets in the practical configurations (e.g., airplanes and wind turbines) remain unfeasible for its huge computational cost. In this study, a general strategy for modelling the effects of riblets in turbulent flows is proposed. Riblets are modelled by adopting a slip-boundary condition on the smooth wall. A quantitative relationship between the riblet geometric parameters and the slip length is theoretically built for the first time. This modelling method could greatly reduce grid numbers in the validating procedure by using Large-Eddy Simulation, and the modelling results indicate that the flow fields in logarithmic and wake regions over riblets could be accurately reproduced. Additionally, considering the slip-boundary model is not capable of reproducing the near-wall flow, a simplified calculating method is developed.
- 10 April 2020
- Published by Springer Nature in Acta Mechanica Sinica
- Vol. 36 (2) , 275-289
Aerodynamic load control on a dynamically pitching wind turbine airfoil using leading-edge protuberance method
- 10 April 2020
- Published by Springer Nature in Acta Mechanica Sinica
- Vol. 36 (2) , 275-289
Aerodynamic load control on a dynamically pitching wind turbine airfoil using leading-edge protuberance method
- Open Access
- 1 January 2017
- Published by Taylor & Francis in Engineering Applications of Computational Fluid Mechanics
- Vol. 11 (1) , 193-209
Numerical simulation of flow characteristics behind the aerodynamic performances on an airfoil with leading edge protuberances
This article presents a numerical investigation of the effects of leading-edge protuberances on airfoil stall and post-stall performance. An improved delayed detached eddy simulation (IDDES) method was adopted. As a result, to clarify the effects of ‘bi-periodic’ phenomenon around stall region, it was found that the flow separation at troughs was the main inducement of aerodynamic lift degradation within pre-stall regime and the flow pattern where vortices diverged was predominant. It was also found that the variations in flow patterns led to the gentle stall process. Furthermore, to study the statistical characteristics of unsteady vortex shedding, corresponding spectrum characteristics were also analyzed from another perspective, suggesting that the vortex shedding frequency was higher where vortices converged. Eventually, the improved performances of tubercled airfoil within post-stall regime could be attributed to the strong streamwise vortices generated by the leading-edge protuberances. Deploying the methods of vortex dynamics, the generation and evolution of the streamwise vortices were depicted. It turned out that the primary and secondary vortices were induced by spanwise pressure gradient at airfoil surface; meanwhile, vortex stretching played a key role in primary vortex evolution, which initially enhanced the strength of vortices corresponding to the acceleration of streamwise velocity.
- 1 January 2017
- Published by Taylor & Francis in Engineering Applications of Computational Fluid Mechanics
- Vol. 11 (1) , 193-209
Open AccessNumerical simulation of flow characteristics behind the aerodynamic performances on an airfoil with leading edge protuberances
This article presents a numerical investigation of the effects of leading-edge protuberances on airfoil stall and post-stall performance. An improved delayed detached eddy simulation (IDDES) method was adopted. As a result, to clarify the effects of ‘bi-periodic’ phenomenon around stall region, it was found that the flow separation at troughs was the main inducement of aerodynamic lift degradation within pre-stall regime and the flow pattern where vortices diverged was predominant. It was also found that the variations in flow patterns led to the gentle stall process. Furthermore, to study the statistical characteristics of unsteady vortex shedding, corresponding spectrum characteristics were also analyzed from another perspective, suggesting that the vortex shedding frequency was higher where vortices converged. Eventually, the improved performances of tubercled airfoil within post-stall regime could be attributed to the strong streamwise vortices generated by the leading-edge protuberances. Deploying the methods of vortex dynamics, the generation and evolution of the streamwise vortices were depicted. It turned out that the primary and secondary vortices were induced by spanwise pressure gradient at airfoil surface; meanwhile, vortex stretching played a key role in primary vortex evolution, which initially enhanced the strength of vortices corresponding to the acceleration of streamwise velocity.
- 1 March 2016
- Published by Elsevier in Science Bulletin
- Vol. 61 (6) , 481-487
Investigation on 3D flow field induced by a plasma actuator with serrated electrode
- 1 March 2016
- Published by Elsevier in Science Bulletin
- Vol. 61 (6) , 481-487
Investigation on 3D flow field induced by a plasma actuator with serrated electrode
- 1 October 2015
- Published by Elsevier in Science Bulletin
- Vol. 60 (19) , 1680-1687
Smart load control of the large-scale offshore wind turbine blades subject to wake effect
- 1 October 2015
- Published by Elsevier in Science Bulletin
- Vol. 60 (19) , 1680-1687
Smart load control of the large-scale offshore wind turbine blades subject to wake effect