Renguo Lu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Renguo Lu has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- Hiroshi Tani
Mechanical Engineering Department, Kansai University, Osaka, Japan
26 shared publications - Shinji Koganezawa
Department of Mechanical Engineering, Kansai University, Suita, Japan
26 shared publications - Norio Tagawa
Kansai University
16 shared publications - Shouhei Kawada
Department of Mechanical Engineering, Kansai University
10 shared publications Hidetaka Nanao
Iwate University
2 shared publicationsHiroshi Tani
Faculty of Engineering Science, Kansai University
2 shared publications
Latest Publications
- Open Access
- 20 February 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (2) , 95
Early-Stage Damage Diagnosis of Rolling Bearings Based on Acoustic Emission Signals Interpreted by Friction Behavior and Machine Learning
Condition monitoring of rolling bearings is essential for ensuring the reliability of mechanical systems operating under severe or insufficient lubrication conditions. This study proposes a fault diagnosis framework that integrates tribological interpretation of wear phenomena, acoustic emission (AE) signal analysis, and machine learning, based on bearing life tests conducted under dry conditions as an accelerated wear environment to capture damage progression within a practical experimental time. Unlike conventional studies relying on artificially introduced defects, this work focuses on AE signals obtained from bearings in which damage initiates and progresses through actual wear processes. Life tests were conducted using deep groove ball bearings under two radial load conditions. The temporal evolution of the coefficient of friction, AE signals, and surface damage was analyzed. Although the coefficient of friction was the most sensitive indicator of wear progression, its direct measurement is impractical for in-service applications. Frequency-domain analysis revealed that AE counts per second and band-specific AE energy exhibit early changes consistent with the evolution of the friction coefficient. Using these physically interpretable AE features, a fully connected neural network was developed to classify bearing conditions into normal, early-stage damage, and damage progression. The proposed model achieved an average classification accuracy of approximately 85%, demonstrating the effectiveness of AE-based machine learning for bearing fault diagnosis under real wear progression conditions rather than artificial defect scenarios.
- 20 February 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (2) , 95
Open AccessEarly-Stage Damage Diagnosis of Rolling Bearings Based on Acoustic Emission Signals Interpreted by Friction Behavior and Machine Learning
Condition monitoring of rolling bearings is essential for ensuring the reliability of mechanical systems operating under severe or insufficient lubrication conditions. This study proposes a fault diagnosis framework that integrates tribological interpretation of wear phenomena, acoustic emission (AE) signal analysis, and machine learning, based on bearing life tests conducted under dry conditions as an accelerated wear environment to capture damage progression within a practical experimental time. Unlike conventional studies relying on artificially introduced defects, this work focuses on AE signals obtained from bearings in which damage initiates and progresses through actual wear processes. Life tests were conducted using deep groove ball bearings under two radial load conditions. The temporal evolution of the coefficient of friction, AE signals, and surface damage was analyzed. Although the coefficient of friction was the most sensitive indicator of wear progression, its direct measurement is impractical for in-service applications. Frequency-domain analysis revealed that AE counts per second and band-specific AE energy exhibit early changes consistent with the evolution of the friction coefficient. Using these physically interpretable AE features, a fully connected neural network was developed to classify bearing conditions into normal, early-stage damage, and damage progression. The proposed model achieved an average classification accuracy of approximately 85%, demonstrating the effectiveness of AE-based machine learning for bearing fault diagnosis under real wear progression conditions rather than artificial defect scenarios.
- Open Access
- 9 April 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (4) , 173
Effect of Applied Current on Tribological Properties of Polyphenyl Ether
The widespread adoption of electric vehicles (EVs) has introduced new challenges in drivetrain lubrication, particularly concerning electrical corrosion, frictional wear, and hydrogen embrittlement. While polyalphaolefin (PAO)-based lubricants are commonly used, they struggle under high-speed and high-torque conditions. In contrast, polyphenyl ether (PPE)-based lubricants offer superior wear resistance and effectively suppress hydrogen generation, making them promising for EV applications. This study examines the effects of current direction and magnitude on tribofilm formation and frictional behavior in a PPE-lubricated environment. The results show that PPE exhibits unique tribofilm adhesion characteristics influenced by electrical conditions, unlike PAO. Surface analysis reveals that the tribofilm mainly consists of amorphous carbon, and friction under an electrical bias induces PPE oxidation, with oxidation products forming more readily at the positive electrode. Tribofilm formation correlated with increased friction and wear, particularly under currents of 10 mA or higher. Although PPE is more sensitive to electrical influences than PAO, it exhibits excellent wear resistance and maintains a low coefficient of friction even under electrification. This suggests that PPE could be suitable for lubrication in electrical environments and may serve as a promising lubricant for EV drive systems and similar applications.
- 9 April 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (4) , 173
Open AccessEffect of Applied Current on Tribological Properties of Polyphenyl Ether
The widespread adoption of electric vehicles (EVs) has introduced new challenges in drivetrain lubrication, particularly concerning electrical corrosion, frictional wear, and hydrogen embrittlement. While polyalphaolefin (PAO)-based lubricants are commonly used, they struggle under high-speed and high-torque conditions. In contrast, polyphenyl ether (PPE)-based lubricants offer superior wear resistance and effectively suppress hydrogen generation, making them promising for EV applications. This study examines the effects of current direction and magnitude on tribofilm formation and frictional behavior in a PPE-lubricated environment. The results show that PPE exhibits unique tribofilm adhesion characteristics influenced by electrical conditions, unlike PAO. Surface analysis reveals that the tribofilm mainly consists of amorphous carbon, and friction under an electrical bias induces PPE oxidation, with oxidation products forming more readily at the positive electrode. Tribofilm formation correlated with increased friction and wear, particularly under currents of 10 mA or higher. Although PPE is more sensitive to electrical influences than PAO, it exhibits excellent wear resistance and maintains a low coefficient of friction even under electrification. This suggests that PPE could be suitable for lubrication in electrical environments and may serve as a promising lubricant for EV drive systems and similar applications.
- 2 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 61 (4) , 1-5
Head Smear Reduction in Head-Disk Interface of HAMR Using External AC Electric Field
Head smear in a head-disk interface (HDI) of the heat-assisted magnetic recording disturbs the head flyability. This study focused on the effect of an external ac electric field on reducing head smears. The smear amount from the disks with lubricant films under an ac electric field and laser heating was evaluated. The smear amount decreased when an electric field was applied between the disk and pin. This is because the ions that desorb from the disk surface get trapped in the space between the disk and pin surfaces and do not reach the pin surface because of the ac electric field.
- 2 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 61 (4) , 1-5
Head Smear Reduction in Head-Disk Interface of HAMR Using External AC Electric Field
Head smear in a head-disk interface (HDI) of the heat-assisted magnetic recording disturbs the head flyability. This study focused on the effect of an external ac electric field on reducing head smears. The smear amount from the disks with lubricant films under an ac electric field and laser heating was evaluated. The smear amount decreased when an electric field was applied between the disk and pin. This is because the ions that desorb from the disk surface get trapped in the space between the disk and pin surfaces and do not reach the pin surface because of the ac electric field.
- 23 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 8 (9) , 1-4
Vibration-Based Scour-Detection for Bridge-Piers Using a Self-Powered Magnetostrictive Vibration Sensor
Considering the drawbacks of existing scour detection systems, such as expense for installation and sensitivity to pier damage, this study developed a vibration-based scour detection sensor that can be installed without the construction of power lines. Our final objective is the realization of a system that can generate electric power from bridge vibrations caused by passing trains, temporarily store the generated energy, use that energy to measure the natural frequency of a bridge pier, and transmit the measurement results to a server via wireless communication. As the first step in the system development, we conducted field tests to confirm whether the developed sensor could measure the natural frequencies of bridge piers. The time-series data of the sensor output were obtained and transmitted using a wireless transmission module, which was made as a part of the development of the system. The experimental results confirmed that the natural frequencies of the bridge pier could be measured even from the output voltage caused by the microtremors of the pier. Thus, the developed vibration sensor can be used to conduct long-term monitoring of the scour conditions of bridge piers.
- 23 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 8 (9) , 1-4
Vibration-Based Scour-Detection for Bridge-Piers Using a Self-Powered Magnetostrictive Vibration Sensor
Considering the drawbacks of existing scour detection systems, such as expense for installation and sensitivity to pier damage, this study developed a vibration-based scour detection sensor that can be installed without the construction of power lines. Our final objective is the realization of a system that can generate electric power from bridge vibrations caused by passing trains, temporarily store the generated energy, use that energy to measure the natural frequency of a bridge pier, and transmit the measurement results to a server via wireless communication. As the first step in the system development, we conducted field tests to confirm whether the developed sensor could measure the natural frequencies of bridge piers. The time-series data of the sensor output were obtained and transmitted using a wireless transmission module, which was made as a part of the development of the system. The experimental results confirmed that the natural frequencies of the bridge pier could be measured even from the output voltage caused by the microtremors of the pier. Thus, the developed vibration sensor can be used to conduct long-term monitoring of the scour conditions of bridge piers.
- Open Access
- 13 March 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (3) , 91
Tribofilm Formation and Friction Reduction Performance on Laser-Textured Surface with Micro-Grooved Structures
Tribofilms, resulting from tribochemical reactions involving lubricants, additives, and metal surfaces, are pivotal in reducing friction, preventing adhesion, and minimizing wear. This study investigates the tribological characteristics of textured surfaces in boundary lubrication, emphasizing the impact of surface texturing on tribofilm formation. Untextured surfaces manifest high friction coefficients and low wear owing to the development of thick tribofilms. However, debris accumulation impedes further tribochemical reactions, necessitating more energy for sliding and resulting in higher friction coefficients. Additionally, molybdenum dialkyl dithiocarbamate-derived MoS2 oxidation diminishes the expected lubrication effect. Textured surfaces exhibit lower friction coefficients and higher wear because the structure aids debris removal, promoting the formation of thinner tribofilms. Despite increased wear from solid-to-solid contact, textured surfaces facilitate an early fluid lubrication transition and enhance cavitation capacity, leading to reduced friction coefficients. We also consider the impact of sliding direction angles on friction coefficients, revealing that lower angles parallel to the grooves heighten friction, whereas higher angles enhance cavitation capacity. Unexpectedly, a 90° sliding direction angle increases the friction coefficients, attributed to MoS2 distribution in the tribofilms. These results provide crucial insights for optimizing lubrication strategies and enhancing wear resistance in boundary lubrication scenarios.
- 13 March 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (3) , 91
Open AccessTribofilm Formation and Friction Reduction Performance on Laser-Textured Surface with Micro-Grooved Structures
Tribofilms, resulting from tribochemical reactions involving lubricants, additives, and metal surfaces, are pivotal in reducing friction, preventing adhesion, and minimizing wear. This study investigates the tribological characteristics of textured surfaces in boundary lubrication, emphasizing the impact of surface texturing on tribofilm formation. Untextured surfaces manifest high friction coefficients and low wear owing to the development of thick tribofilms. However, debris accumulation impedes further tribochemical reactions, necessitating more energy for sliding and resulting in higher friction coefficients. Additionally, molybdenum dialkyl dithiocarbamate-derived MoS2 oxidation diminishes the expected lubrication effect. Textured surfaces exhibit lower friction coefficients and higher wear because the structure aids debris removal, promoting the formation of thinner tribofilms. Despite increased wear from solid-to-solid contact, textured surfaces facilitate an early fluid lubrication transition and enhance cavitation capacity, leading to reduced friction coefficients. We also consider the impact of sliding direction angles on friction coefficients, revealing that lower angles parallel to the grooves heighten friction, whereas higher angles enhance cavitation capacity. Unexpectedly, a 90° sliding direction angle increases the friction coefficients, attributed to MoS2 distribution in the tribofilms. These results provide crucial insights for optimizing lubrication strategies and enhancing wear resistance in boundary lubrication scenarios.
- Open Access
- 31 July 2023
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 18 (3) , 83-90
The Influence of Electric Current on the Friction Behavior of Lubricant Molecules
The electrical failure of bearings has become a critical issue that restricts the lifetime of all-electric motor-based power systems in electric vehicles (EVs). This study aims to explain the electrically induced frictional behavior of lubricants. The effect of external electric current applied between the friction pairs on tribological properties was examined using a disk-on-ring friction tester. The surface potential analysis demonstrated that applying a positive electric current by connecting the friction surface to the cathode decreased surface activity, whereas a negative electric current increased it. The direction of the electric current influenced the friction coefficient, with a rapid increase observed when a positive current was applied. The lower ring’s friction surface exhibited reduced lubricant adsorption. Consequently, fewer lubricant molecules were transferred to the friction interface, producing a high friction coefficient. Moreover, the wear surface experienced pitting after applying an external electric current, suggesting that pitting contributed to accelerated wear. These findings provide insights into the influence of electric current on the tribological properties of lubricants and have implications for the design of tribological systems in EVs.
- 31 July 2023
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 18 (3) , 83-90
Open AccessThe Influence of Electric Current on the Friction Behavior of Lubricant Molecules
The electrical failure of bearings has become a critical issue that restricts the lifetime of all-electric motor-based power systems in electric vehicles (EVs). This study aims to explain the electrically induced frictional behavior of lubricants. The effect of external electric current applied between the friction pairs on tribological properties was examined using a disk-on-ring friction tester. The surface potential analysis demonstrated that applying a positive electric current by connecting the friction surface to the cathode decreased surface activity, whereas a negative electric current increased it. The direction of the electric current influenced the friction coefficient, with a rapid increase observed when a positive current was applied. The lower ring’s friction surface exhibited reduced lubricant adsorption. Consequently, fewer lubricant molecules were transferred to the friction interface, producing a high friction coefficient. Moreover, the wear surface experienced pitting after applying an external electric current, suggesting that pitting contributed to accelerated wear. These findings provide insights into the influence of electric current on the tribological properties of lubricants and have implications for the design of tribological systems in EVs.
- 27 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (11) , 1-5
Feasibility Study of Reduction in Sound-Pressure-Induced Vibration in Hard Disk Drives Using Adaptive Feed-Forward Control
In recent years, sound-pressure-induced positioning errors have become a critical issue in hard disk drives (HDDs) for data centers. As these positioning errors often contain components with frequencies higher than the servo bandwidth, we conducted a feasibility study of adaptive feed-forward (AFF) control to suppress the vibrations. By placing a sensor to detect the vibration on the pivot shaft, the correlation between the sensor signal and head vibration was obtained. The HDD with AFF control applied is assumed to have a dual-stage actuator system, where the secondary actuator compensates for the sound-pressure-induced positioning errors. Simulation results confirmed that the proposed control effectively suppressed the sound-pressure-induced vibrations.
- 27 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (11) , 1-5
Feasibility Study of Reduction in Sound-Pressure-Induced Vibration in Hard Disk Drives Using Adaptive Feed-Forward Control
In recent years, sound-pressure-induced positioning errors have become a critical issue in hard disk drives (HDDs) for data centers. As these positioning errors often contain components with frequencies higher than the servo bandwidth, we conducted a feasibility study of adaptive feed-forward (AFF) control to suppress the vibrations. By placing a sensor to detect the vibration on the pivot shaft, the correlation between the sensor signal and head vibration was obtained. The HDD with AFF control applied is assumed to have a dual-stage actuator system, where the secondary actuator compensates for the sound-pressure-induced positioning errors. Simulation results confirmed that the proposed control effectively suppressed the sound-pressure-induced vibrations.
- 14 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (11) , 1-5
Effect of Humidity on Head Smear Generation in Head-Assisted Magnetic Recording
The causes of head smears deposited on the magnetic head surface due to laser heating in heat-assisted magnetic recording should be investigated to achieve high recording densities of hard disk drives. These factors, such as outgassing from components and humidity, also affect smear formation in hard disk drives. In this study, we focused on the effect of relative humidity on smears generated via laser heating. Three types of lubricant film (dipped, ultraviolet-treated, and rinsed) were prepared, and the amount of smear generated on a glass pin surface was evaluated using a pin-on-disk tester with a laser heating system. It was confirmed that the amount of smear increased as the humidity increased, and lubricant films with higher chemical bonding fractions showed less smear generation and lower dependence on humidity. In addition, time-of-flight secondary ion mass spectroscopy confirmed that the migration of cobalt from the magnetic layer was accelerated by laser heating and humidity.
- 14 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (11) , 1-5
Effect of Humidity on Head Smear Generation in Head-Assisted Magnetic Recording
The causes of head smears deposited on the magnetic head surface due to laser heating in heat-assisted magnetic recording should be investigated to achieve high recording densities of hard disk drives. These factors, such as outgassing from components and humidity, also affect smear formation in hard disk drives. In this study, we focused on the effect of relative humidity on smears generated via laser heating. Three types of lubricant film (dipped, ultraviolet-treated, and rinsed) were prepared, and the amount of smear generated on a glass pin surface was evaluated using a pin-on-disk tester with a laser heating system. It was confirmed that the amount of smear increased as the humidity increased, and lubricant films with higher chemical bonding fractions showed less smear generation and lower dependence on humidity. In addition, time-of-flight secondary ion mass spectroscopy confirmed that the migration of cobalt from the magnetic layer was accelerated by laser heating and humidity.
- 1 January 2023
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Conference on Information, Intelligence and Precision Equipment : IIP
- Vol. 2023, IIPC-7-8-7
Estimation of tire wear using piezoelectric films arranged in parallel
The development of intelligent tires that employ sensors to monitor road surface information and tire conditions has been underway for realizing safe and secure mobility for society. This paper describes a wear estimation method for tires using piezoelectric films arranged in parallel. We compared the outputs of multiple piezoelectric films between the new and worn tires. The ratio of the peak interval time to one tire rotation period(time ratio) and the ratio of positive voltage to negative voltage (voltage ratio) were analyzed. The position where the voltage ratio is large shifts in the direction of the tire side due to wear. There is no difference in the time ratio in the central part of the tire before and after wear, but it decreases in the lateral part of the tire. These are due to the fact that the contact patch width widens due to wear, and the sidewall section begins to support the load.
- 1 January 2023
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Conference on Information, Intelligence and Precision Equipment : IIP
- Vol. 2023, IIPC-7-8-7
Estimation of tire wear using piezoelectric films arranged in parallel
The development of intelligent tires that employ sensors to monitor road surface information and tire conditions has been underway for realizing safe and secure mobility for society. This paper describes a wear estimation method for tires using piezoelectric films arranged in parallel. We compared the outputs of multiple piezoelectric films between the new and worn tires. The ratio of the peak interval time to one tire rotation period(time ratio) and the ratio of positive voltage to negative voltage (voltage ratio) were analyzed. The position where the voltage ratio is large shifts in the direction of the tire side due to wear. There is no difference in the time ratio in the central part of the tire before and after wear, but it decreases in the lateral part of the tire. These are due to the fact that the contact patch width widens due to wear, and the sidewall section begins to support the load.
- 1 January 2023
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Conference on Information, Intelligence and Precision Equipment : IIP
- Vol. 2023, IIPC-7-9-7
Development of an actuator for reduction in inspection time of gastrointestinal endoscopy
Capsule endoscopes are often used for medical examinations of the digestive system. Currently, endoscopy examination takes a few days to be completed because capsules do not have any actuator. In this study, an inclined-leg actuator inspired by Setaria viridis was developed. Small-sized inclined-leg actuators of the angles (75°) were designed and fabricated, considering as parameters the lengths (4 mm, 8 mm, and 12 mm) of the legs; the running velocities of the actuators were measured when vibrations with different frequencies and amplitudes were applied. At frequencies > 40 Hz, the actuator velocities exceeded the target speed of >10 mm/s. Therefore, the proposed design of vibration-driven actuator has potential to be applied in capsule endoscopes.
- 1 January 2023
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Conference on Information, Intelligence and Precision Equipment : IIP
- Vol. 2023, IIPC-7-9-7
Development of an actuator for reduction in inspection time of gastrointestinal endoscopy
Capsule endoscopes are often used for medical examinations of the digestive system. Currently, endoscopy examination takes a few days to be completed because capsules do not have any actuator. In this study, an inclined-leg actuator inspired by Setaria viridis was developed. Small-sized inclined-leg actuators of the angles (75°) were designed and fabricated, considering as parameters the lengths (4 mm, 8 mm, and 12 mm) of the legs; the running velocities of the actuators were measured when vibrations with different frequencies and amplitudes were applied. At frequencies > 40 Hz, the actuator velocities exceeded the target speed of >10 mm/s. Therefore, the proposed design of vibration-driven actuator has potential to be applied in capsule endoscopes.