QLQiang Li

Qiang Li

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Qiang Li has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Numerical simulation of macroscopic viscoelastic melt filling and mesoscopic spherulite growth

    by Huisi Wan, Qiang Li, Huan Li

    In this work, a non-isothermal viscoelastic computational framework is proposed for macroscopic polymer melt filling and mesoscopic spherulite growth. Firstly, the macroscopic viscoelastic governing equation is solved by coupled level set immersed boundary and finite-volume (LS-IB-FV) method. The melt-air interface is captured by the coupled level-set and volume-of-fluid (CLSVOF) method. And the mesoscopic crystallization behavior is predicted by the phase field model. Then, the numerical simulation for melt filling process is compared with experimental one to validate the coupled method. And it is simulated that the melt filling stage in a complex annular cavity with 17 small solid discs for the semi-crystalline polymer of isotactic polystyrene, and it is studied that the impacts of three different injection velocities on the flow modes, temperature distribution and solidified layers. Finally, in the regions of solidified layers, the growth of spherulites is simulated with/without melt flows at two different points. Numerical results show that the injection velocities can affect the flow modes and temperature distribution significantly. The morphology of polymer spherulite that is consistent with the experimental result can be observed clearly. With flow fields, the spherulites grow faster and densely towards the upstream direction.


  • Open Access

    CFD-DEM Simulation of Fast Fluidization of Fine Particles in a Micro Riser

    by Guorong Wu, Qiang Li, Zhanfei Zuo

    In recent years, the discrete element method (DEM) has gradually been applied to the traditional fluidization simulation of fine particles in a micro fluidized bed (MFB). The application of DEM in the simulating fast fluidization of fine particles in MFB has not yet received attention. This article presents a drag model that relies on the surrounding environment of particles, namely the particle circumstance-dependent drag model or PCDD model. Fast fluidization in an MFB of fine particles is simulated using DEM based on the PCDD model. Simulations indicate that the local structure in an MFB exhibits particle aggregation, which is a natural property of fast fluidization, forming a structure where a continuous dilute phase and dispersed concentrated phase coexist. There exists a strong effect of solid back-mixing in an MFB, leading to relatively low outlet solid flux. The gas back-mixing effect is, however, not so distinct. The axial porosity shows a monotonically increasing distribution with the bed height but does not strictly follow the single exponential distribution. The solid volume fraction at the bottom of the bed is significantly lower than the correlated value in CFB. The axial heterogeneous distribution of the cross-sectional average porosity in the lower half of the bed is also weakened. The radial porosity shows a higher distribution pattern in the central region and a lower one in the sidewall region.


  • Open Access

    DEM Simulation of Fast Fluidization of Fine Particles in a Micro Riser

    by Guorong Wu, Qiang Li, Zhanfei Zuo

    In recent years discrete element method (DEM) has gradually been applied to the traditional fluidization simulation of fine particles in micro fluidized bed (MFB). The application of DEM in simulating fast fluidization of fine particles in MFB has not yet received attention. This article presents a drag model that relies on the surrounding environment of particles, namely particle circumstance-dependent drag modle or PCDD model. Fast fluidization in MFB of fine particles is simulated using DEM based on the PCDD model. It is found that the gas-solid two-phase flow in MFB meets the common law of fast fluidization in circulating fluidized bed (CFB) to a certain extent, and also presents a special law that is significantly different from that in CFB. Simulations indicate that the local structure in MFB exhibits particle aggregation which is a natural property of fast fluidized, forming a structure where continuous dilute phase and dispersed concentrated phase coexist. The formation and fragmentation of particle clusters in different local regions of the bed have time synchronization. There exists strong effect of solid back-mixing in MFB, leading to relatively low outlet solid flux. The gas back-mixing effect is, however, not so distinct. The axial porosity shows a monotonically increasing distribution with the bed height, but does not strictly follow the single exponential distribution. The solid volume fraction at the bottom of the bed is significantly lower than the correlated value in CFB. The axial heterogeneous distribution of the cross-sectional average porosity in the lower half of the bed is also weakened. The radial porosity shows a distribution pattern of higher in the central region and lower in the sidewall region. Compared with the correlation results in CFB, the porosity near the central region in MFB is relatively low, while the porosity near the sidewall region is relatively high. The geometric size of the container, especially the radial size, is much smaller than that of a CFB. The relative area of contact between the MFB wall and particles is larger, and the wall friction factor becomes more significant. This may be the main reason for the time synchronization of particle agglomeration, severe particle back-mixing, low outlet solid flux, monotonically increasing axial porosity and weak core-annular structure of radial porosity.


  • Macroscopic and mesoscopic simulation of viscoelastic free surface flow in gas‐assisted injection moulding process

    by Qiang Li, Haifeng Niu, Jinyun Yuan

    In this work, an improved simple coupled level‐set and volume of fluid (S‐CLSVOF) method is proposed to trace the moving interfaces in gas assisted injection moulding (GAIM) process based on the viscoelastic FENE‐P model. Firstly, the Kreisselmeier‐Steinhauser (KS) function constructed by means of Boolean operations is adopted as the shape level set (LS) function to precisely represent the complex mould cavities. Then, the benchmark problem of two‐dimensional deformation is used to verify the ability of the S‐CLSVOF method for capturing the moving interfaces. The stress birefringence is calculated and compared with the experiment result. Finally, the proposed method is further applied to the mould filling and gas penetration processes in GAIM. The macroscopic bubble appearance, temperature distribution, and the behaviour of the mesoscopic molecular orientation are shown and analyzed in detail. Due to the complexity of the gas‐liquid interaction, the phenomenon of asymmetrical gas flow is clearly observed in the gas penetration process. The influences of the macroscopic parameters on the macroscopic gas flows and mesoscopic molecular orientation are also discussed, such as insert positions, melt temperatures, and gas delay time. The numerical results illustrate that the coupled method can be applied to the multiscale numerical simulation of viscoelastic flows with complex free surfaces and provide significant guidance for the GAIM process.


  • Three‐dimensional simulations of non‐isothermal flow for gas penetration in complex cavity during gas assisted injection moulding process

    by Qiang Li, Haifeng Niu

    In this paper an R‐function is employed to construct the shape level set (LS) function for representing the complex mould cavity in a gas‐assisted injection moulding (GAIM) process. With the shape LS function, the continuity, momentum, and energy equations can be extended for solving the gas‐liquid two‐phase flows using the finite volume and immersed boundary methods. Firstly, an improved simple coupled level set and volume of fluid (S‐CLSVOF) method is proposed to track the moving interfaces of gas‐liquid interface and polymer melt front. Then the benchmark problems of the two‐ and three‐dimensional deformation tests are carried out to verify the ability of the improved S‐CLSVOF method. At last, the gas penetration processes are simulated in two different complex mould cavities. The numerical results show that the improved S‐CLSVOF method has higher accuracy than the S‐CLSVOF method, and the coupled numerical framework can successfully depict the asymmetry phenomenon of gas flow, racetracking, and fountain phenomena, which has great significance in determining processing conditions and designing mould cavities.


  • Numerical simulation on weld line development of injection molding in mold cavity with inserts

    by Li Qiang, Li Wu-Ming

    A gas-liquid two-phase model for a viscoelastic fluid is proposed and used to simulate and predict the behavior of melt welding in injection molding process, in which the extended pom-pom (XPP) model and cross-WLF viscosity model combined with Tait state equation are used to describe the constitutive relationship and viscosity change of the viscoelastic melt in this paper, respectively. Meanwhile, the coupled level-set and volume-of-fluid (CLSVOF) method is employed to capture the melt front, and the immersed boundary method is applied to the simulation of the polymer melt flows with the aid of a shaped level-set function to describe and treat the irregular mold cavities. A finite volume method on non-staggered grid is used to solve the mass, momentum, and energy conservation equations. Firstly, the benchmark problem of the single shear flow is simulated to verify the validity of the CLSVOF method. Then, the non-isothermal filling process of the viscoelastic fluid based on the XPP model in a mold with square inset is simulated, and the behavior of the weld line devolopment in the filling process is shown and compared with the experimental result. Finally, it is to simulate the evolution processes of the melt front interface and weld line in a mold with the circular notched inset; and the linear stress-optical rule is adopted to calculate the flow-induced birefringence. Numerical results show that the numerical model proposed in this paper can be employed to simulate the non-isothermal filling process in complex mold cavity and to capture the weld line automatically. Because of the complexity of polymer melt flows, the flow-induced stress increases quickly near the weld line region and then decreases gradually until reaching the mold cavity wall. The maximum value of the flow-induced stress appears at some point after the insert. The distributions of physical quantities, such as pressure and temperature in the mold, are given during the mold filling process. Moreover, it is also discussed the influence of melt and mold temperatures on the solidified layer thickness. The higher the melt or mold temperature, the thinner the solidified layer is. Thus, raising the melt or the mold temperature will improve or remove the weld line in melt filling process.