GWGuorong Wu

Guorong Wu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Guorong Wu has a total of 5 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    CFD-DEM Simulation of Fast Fluidization of Fine Particles in a Micro Riser

    by Guorong Wu, Qiang Li, Zhanfei Zuo

    In recent years, the discrete element method (DEM) has gradually been applied to the traditional fluidization simulation of fine particles in a micro fluidized bed (MFB). The application of DEM in the simulating fast fluidization of fine particles in MFB has not yet received attention. This article presents a drag model that relies on the surrounding environment of particles, namely the particle circumstance-dependent drag model or PCDD model. Fast fluidization in an MFB of fine particles is simulated using DEM based on the PCDD model. Simulations indicate that the local structure in an MFB exhibits particle aggregation, which is a natural property of fast fluidization, forming a structure where a continuous dilute phase and dispersed concentrated phase coexist. There exists a strong effect of solid back-mixing in an MFB, leading to relatively low outlet solid flux. The gas back-mixing effect is, however, not so distinct. The axial porosity shows a monotonically increasing distribution with the bed height but does not strictly follow the single exponential distribution. The solid volume fraction at the bottom of the bed is significantly lower than the correlated value in CFB. The axial heterogeneous distribution of the cross-sectional average porosity in the lower half of the bed is also weakened. The radial porosity shows a higher distribution pattern in the central region and a lower one in the sidewall region.


  • Open Access

    DEM Simulation of Fast Fluidization of Fine Particles in a Micro Riser

    by Guorong Wu, Qiang Li, Zhanfei Zuo

    In recent years discrete element method (DEM) has gradually been applied to the traditional fluidization simulation of fine particles in micro fluidized bed (MFB). The application of DEM in simulating fast fluidization of fine particles in MFB has not yet received attention. This article presents a drag model that relies on the surrounding environment of particles, namely particle circumstance-dependent drag modle or PCDD model. Fast fluidization in MFB of fine particles is simulated using DEM based on the PCDD model. It is found that the gas-solid two-phase flow in MFB meets the common law of fast fluidization in circulating fluidized bed (CFB) to a certain extent, and also presents a special law that is significantly different from that in CFB. Simulations indicate that the local structure in MFB exhibits particle aggregation which is a natural property of fast fluidized, forming a structure where continuous dilute phase and dispersed concentrated phase coexist. The formation and fragmentation of particle clusters in different local regions of the bed have time synchronization. There exists strong effect of solid back-mixing in MFB, leading to relatively low outlet solid flux. The gas back-mixing effect is, however, not so distinct. The axial porosity shows a monotonically increasing distribution with the bed height, but does not strictly follow the single exponential distribution. The solid volume fraction at the bottom of the bed is significantly lower than the correlated value in CFB. The axial heterogeneous distribution of the cross-sectional average porosity in the lower half of the bed is also weakened. The radial porosity shows a distribution pattern of higher in the central region and lower in the sidewall region. Compared with the correlation results in CFB, the porosity near the central region in MFB is relatively low, while the porosity near the sidewall region is relatively high. The geometric size of the container, especially the radial size, is much smaller than that of a CFB. The relative area of contact between the MFB wall and particles is larger, and the wall friction factor becomes more significant. This may be the main reason for the time synchronization of particle agglomeration, severe particle back-mixing, low outlet solid flux, monotonically increasing axial porosity and weak core-annular structure of radial porosity.


  • Open Access

    Research on the Mesoscopic Characteristics of Kelvin–Helmholtz Instability in Polymer Fluids with Dissipative Particle Dynamics

    by Guorong Wu, Yanggui Li, Heping Wang, Shengshan Li

    In this paper, the two-dimensional Kelvin–Helmholtz (KH) instability occurring in the shear flow of polymer fluids is modeled by the dissipative particle dynamics (DPD) method at the coarse-grained molecular level. A revised FENE model is proposed to properly describe the polymer chains. In this revised model, the elastic repulsion and tension are both considered between the adjacent beads, the bond length of which is set as one segment’s equilibrium length. The entanglements between polymer chains are described with a bead repulsive potential. The characteristics of such a KH instability in polymer fluid shear flow can be successfully captured in the simulations by the use of the modified FENE model. The numerical results show that the waves and vortexes grow more slowly in the shear flow of the polymer fluids than in the Newtonian fluid case, these vortexes become flat, and the polymer impedes the mixing of fluids and inhibits the generation of turbulence. The effects of the polymer concentration, chain length, and extensibility are also investigated regarding the evolution of KH instability. It is shown that the mixing of two polymer fluids reduces, and the KH instability becomes more suppressed as the polymer concentration increases. The vortexes become much longer with the evolution of the elongated interface as the chain length turns longer. As the extensibility increases, the vortexes become more flattened. Moreover, the roll-up process is significantly suppressed if the polymer has sufficiently high extensibility. These observations show that the polymer and its properties significantly influence the formation and evolution of the coherent structures such as the waves and vortexes in the KH instability progress.