Emeric Plancher
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Emeric Plancher has a total of 60 co-authors. Here are the top co-authors by number of shared publications:
- Olivier Castelnau
Procédés et Ingénierie en Mécanique et Matériaux, CNRS UMR 8006, École Nationale Supérieure des Arts et Métiers, Paris, France
3 shared publications - Cemal Cem Tasan
Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, USA
2 shared publications J. Petit
Université Paris Ouest, Laboratoire LEME, EA4416
2 shared publications- Michel Bornert
Laboratoire Navier
2 shared publications - Alexis Burr
Univ. Grenoble Alpes , CNRS, Grenoble INP, SIMAP, Grenoble, France
1 shared publication Alfonso González
1 shared publication
Latest Publications
- 1 April 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Mesures de champs de déformations élastique et totale pour la détermination du comportement mécanique local de matériaux cristallins.
La connaissance du comportement mécanique à l’échelle du micron est déterminante pour arriver à prédire la dégradation des matériaux. Dans le cas des polycristaux, les lois de plasticité cristalline sont généralement utilisées pour décrire le comportement d’un grain. Ces lois possèdent de nombreux paramètres qui doivent être ajustés à l’état métallurgique et mécanique du matériau.Le travail rapporté ici explore une manière originale d’identifier ces paramètres à partir du comportement observé expérimentalement à l’échelle microscopique, sans recourir à un maillage éléments finis. Cette observation est réalisée en couplant (i) une évaluation du champ de contrainte locale par les techniques de microdiffraction Laue et d’EBSD à haute résolution angulaire et (ii) la mesure du champ de déformation total par corrélation d’images numériques.Afin de garantir la fiabilité des résultats, la justesse des mesures par microdiffraction Laue (Laue-DIC) et HR-EBSD est évaluée, pour la première fois, dans un matériau plastifié à moins de 0,5% de déformation. Les champs de déformation et de contrainte sont ensuite déterminés simultanément en surface d’une éprouvette monocristalline, sollicitée in-situ en flexion quatre points. Le comportement local est ainsi mesuré puis utilisé pour identifier deux paramètres d’une loi de plasticité cristalline, dans un acier austénitique monocristallin de type 316L.
- 1 April 2026
- Published by Agence Bibliographique de l'Enseignement Supérieur
Mesures de champs de déformations élastique et totale pour la détermination du comportement mécanique local de matériaux cristallins.
La connaissance du comportement mécanique à l’échelle du micron est déterminante pour arriver à prédire la dégradation des matériaux. Dans le cas des polycristaux, les lois de plasticité cristalline sont généralement utilisées pour décrire le comportement d’un grain. Ces lois possèdent de nombreux paramètres qui doivent être ajustés à l’état métallurgique et mécanique du matériau.Le travail rapporté ici explore une manière originale d’identifier ces paramètres à partir du comportement observé expérimentalement à l’échelle microscopique, sans recourir à un maillage éléments finis. Cette observation est réalisée en couplant (i) une évaluation du champ de contrainte locale par les techniques de microdiffraction Laue et d’EBSD à haute résolution angulaire et (ii) la mesure du champ de déformation total par corrélation d’images numériques.Afin de garantir la fiabilité des résultats, la justesse des mesures par microdiffraction Laue (Laue-DIC) et HR-EBSD est évaluée, pour la première fois, dans un matériau plastifié à moins de 0,5% de déformation. Les champs de déformation et de contrainte sont ensuite déterminés simultanément en surface d’une éprouvette monocristalline, sollicitée in-situ en flexion quatre points. Le comportement local est ainsi mesuré puis utilisé pour identifier deux paramètres d’une loi de plasticité cristalline, dans un acier austénitique monocristallin de type 316L.
- 20 August 2019
- Published by Springer Nature in Experimental Mechanics
- Vol. 60 (1) , 35-50
Tracking Microstructure Evolution in Complex Biaxial Strain Paths: A Bulge Test Methodology for the Scanning Electron Microscope
- 20 August 2019
- Published by Springer Nature in Experimental Mechanics
- Vol. 60 (1) , 35-50
Tracking Microstructure Evolution in Complex Biaxial Strain Paths: A Bulge Test Methodology for the Scanning Electron Microscope
- 6 August 2019
- Published by Springer Nature in JOM
- Vol. 71 (10) , 3543-3551
Validity of Crystal Plasticity Models Near Grain Boundaries: Contribution of Elastic Strain Measurements at Micron Scale
- 6 August 2019
- Published by Springer Nature in JOM
- Vol. 71 (10) , 3543-3551
Validity of Crystal Plasticity Models Near Grain Boundaries: Contribution of Elastic Strain Measurements at Micron Scale
- 1 August 2019
- Published by Elsevier in Additive Manufacturing
- Vol. 28, 821-830
Effect of ultrasonic shot peening on the surface defects of thin struts built by electron beam melting: Consequences on fatigue resistance
- 1 August 2019
- Published by Elsevier in Additive Manufacturing
- Vol. 28, 821-830
Effect of ultrasonic shot peening on the surface defects of thin struts built by electron beam melting: Consequences on fatigue resistance
- Open Access
- 1 March 2019
- Published by Elsevier in Materials & Design
- Vol. 166
Towards behavior by design: A case study on corrugated architectures
- 1 March 2019
- Published by Elsevier in Materials & Design
- Vol. 166
Open AccessTowards behavior by design: A case study on corrugated architectures
- 1 March 2018
- Published by Elsevier in Ultramicroscopy
- Vol. 186, 35-41
Preventing damage and redeposition during focused ion beam milling: The “umbrella” method
- 1 March 2018
- Published by Elsevier in Ultramicroscopy
- Vol. 186, 35-41
Preventing damage and redeposition during focused ion beam milling: The “umbrella” method
- 1 June 2017
- Published by International Union of Crystallography (IUCr) in Journal of Applied Crystallography
- Vol. 50 (3) , 940-948
Direct measurement of local constitutive relations, at the micrometre scale, in bulk metallic alloys
Multiscale models involving crystal plasticity are essential to predict the elastoplastic behavior of structural materials with respect to their microstructure. However, those models are often limited by a poor knowledge of the local constitutive behavior. This article reports a method to measure the mechanical behavior directly, at the micrometre scale, in bulk crystalline materials. Local strain and stress states were evaluated at the surface of a bent stainless steel crystal by combining total strain measurements – performed with the digital image correlation technique on optical images – with elastic strain measurements obtained by Laue microdiffraction. A local constitutive relation was measured, in an efficient nondestructive way, without the need for full-field simulations. The method was validated by a comparison between the measured local behavior and the macroscopic behavior of the single crystal.
- 1 June 2017
- Published by International Union of Crystallography (IUCr) in Journal of Applied Crystallography
- Vol. 50 (3) , 940-948
Direct measurement of local constitutive relations, at the micrometre scale, in bulk metallic alloys
Multiscale models involving crystal plasticity are essential to predict the elastoplastic behavior of structural materials with respect to their microstructure. However, those models are often limited by a poor knowledge of the local constitutive behavior. This article reports a method to measure the mechanical behavior directly, at the micrometre scale, in bulk crystalline materials. Local strain and stress states were evaluated at the surface of a bent stainless steel crystal by combining total strain measurements – performed with the digital image correlation technique on optical images – with elastic strain measurements obtained by Laue microdiffraction. A local constitutive relation was measured, in an efficient nondestructive way, without the need for full-field simulations. The method was validated by a comparison between the measured local behavior and the macroscopic behavior of the single crystal.
- 11 December 2015
- Published by Springer Nature in Experimental Mechanics
- Vol. 56 (3) , 483-492
On the Accuracy of Elastic Strain Field Measurements by Laue Microdiffraction and High-Resolution EBSD: a Cross-Validation Experiment
- 11 December 2015
- Published by Springer Nature in Experimental Mechanics
- Vol. 56 (3) , 483-492
On the Accuracy of Elastic Strain Field Measurements by Laue Microdiffraction and High-Resolution EBSD: a Cross-Validation Experiment
- 10 November 2015
- Published by International Union of Crystallography (IUCr) in Journal of Applied Crystallography
- Vol. 48 (6) , 1805-1817
Determination of deviatoric elastic strain and lattice orientation by applying digital image correlation to Laue microdiffraction images: the enhanced Laue-DIC method
A new method of determining the deviatoric elastic strain and lattice orientation from Laue microdiffraction images is presented. Standard data treatment methods can suffer from the difficulty of precisely pinpointing the positions of diffraction peaks on two-dimensional Laue images. In a previous article, digital image correlation (DIC) was introduced for the treatment of Laue images, leading to the so-called Laue-DIC method. This performed better than the standard method in terms of the deviatoric elastic strain increment and relative rotation from one lattice to another, particularly when the shape of the Laue spots departs from regular ellipsoids. The present work intends to push forward the Laue-DIC method, aiming to determine the deviatoric elastic strain and lattice orientation, as well as the calibration parameters. The performance of this new method, named enhanced Laue-DIC, is assessed by modeling the spot displacements and accounting for random fluctuations relevant for typical experimental conditions. When the enhanced Laue-DIC method is applied to the case of anin situdeformed Si crystal, the obtained standard deviation of local stress is of the order of 1–2 MPa, while the calibration parameters are optimized to high accuracy.
- 10 November 2015
- Published by International Union of Crystallography (IUCr) in Journal of Applied Crystallography
- Vol. 48 (6) , 1805-1817
Determination of deviatoric elastic strain and lattice orientation by applying digital image correlation to Laue microdiffraction images: the enhanced Laue-DIC method
A new method of determining the deviatoric elastic strain and lattice orientation from Laue microdiffraction images is presented. Standard data treatment methods can suffer from the difficulty of precisely pinpointing the positions of diffraction peaks on two-dimensional Laue images. In a previous article, digital image correlation (DIC) was introduced for the treatment of Laue images, leading to the so-called Laue-DIC method. This performed better than the standard method in terms of the deviatoric elastic strain increment and relative rotation from one lattice to another, particularly when the shape of the Laue spots departs from regular ellipsoids. The present work intends to push forward the Laue-DIC method, aiming to determine the deviatoric elastic strain and lattice orientation, as well as the calibration parameters. The performance of this new method, named enhanced Laue-DIC, is assessed by modeling the spot displacements and accounting for random fluctuations relevant for typical experimental conditions. When the enhanced Laue-DIC method is applied to the case of anin situdeformed Si crystal, the obtained standard deviation of local stress is of the order of 1–2 MPa, while the calibration parameters are optimized to high accuracy.
- 1 May 2013
- Published by Elsevier in Scripta Materialia
- Vol. 68 (10) , 805-808
On dislocation involvement in Ti–Nb gum metal plasticity
- 1 May 2013
- Published by Elsevier in Scripta Materialia
- Vol. 68 (10) , 805-808
On dislocation involvement in Ti–Nb gum metal plasticity