Jaber A. Abu Qahouq
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jaber A. Abu Qahouq has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Lilly Huang
Intel Corporation, Systems Technology Lab - Corporate Technology Group, Hillsboro, Oregon 97124, USA
8 shared publications- Issa Batarseh
University of Central Florida, Orlando, FL, USA
5 shared publications - Lilly Huang
Intel Corporation, Corporate Technology Group - Systems Technology Lab, Hillsboro, Oregon 97124
3 shared publications Wisam Al-Hoor
University of Central Florida, School of Electrical Engineering and Computer Science, Orlando, Florida 32816, USA
3 shared publicationsDoug Huard
Intel Corporation, Hillsboro, Oregon 97124
2 shared publicationsAllan Hallberg
Intel Corporation, Hillsboro, Oregon 97124
1 shared publication
Latest Publications
- 1 May 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02714302,p. 2463-2465
A Converter with Fixed Switching Frequency Adaptive Multi-Mode Control Scheme
A multi-mode adaptive control scheme to achieve high conversion efficiency over wide load range is presented in this paper. The presented controller results in improved efficiency while operating at a fixed switching frequency which guarantees maintained steady-state and dynamic performance at all load conditions. This is achieved by operating in three or more different modes in a reconfigurable topology structure as a function of the load to achieve a reduced total conversion loss which reduces energy usage and extends battery life. Theoretical analysis for the proposed control scheme and comparison with state of the art schemes are presented and validated with a 1.5V /50W proof of concept experimental prototype results.
- 1 May 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02714302,p. 2463-2465
A Converter with Fixed Switching Frequency Adaptive Multi-Mode Control Scheme
A multi-mode adaptive control scheme to achieve high conversion efficiency over wide load range is presented in this paper. The presented controller results in improved efficiency while operating at a fixed switching frequency which guarantees maintained steady-state and dynamic performance at all load conditions. This is achieved by operating in three or more different modes in a reconfigurable topology structure as a function of the load to achieve a reduced total conversion loss which reduces energy usage and extends battery life. Theoretical analysis for the proposed control scheme and comparison with state of the art schemes are presented and validated with a 1.5V /50W proof of concept experimental prototype results.
- 1 May 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02714302,p. 781-784
Adaptive Variable Switching Frequency Digital Controller Algorithm to Optimize Efficiency
An adaptive digital controller with maximum efficiency point tracking to optimize DC-DC converter switching frequency is presented in this paper. The adaptive-frequency-optimization (AFO) method changes the DC-DC converter switching frequency while tracking the converter minimum input power (maximum efficiency) point under variable conditions including variable load and variable input voltage. The AFO digital controller continuously finds the optimum switching frequency that result in the minimum total loss while converter parameters and conditions vary. In this paper, the AFO method is discussed analyzed and its digital control algorithm and experimental implementation are presented.
- 1 May 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02714302,p. 781-784
Adaptive Variable Switching Frequency Digital Controller Algorithm to Optimize Efficiency
An adaptive digital controller with maximum efficiency point tracking to optimize DC-DC converter switching frequency is presented in this paper. The adaptive-frequency-optimization (AFO) method changes the DC-DC converter switching frequency while tracking the converter minimum input power (maximum efficiency) point under variable conditions including variable load and variable input voltage. The AFO digital controller continuously finds the optimum switching frequency that result in the minimum total loss while converter parameters and conditions vary. In this paper, the AFO method is discussed analyzed and its digital control algorithm and experimental implementation are presented.
- 1 February 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in APEC 07 - Twenty-Second Annual IEEE Applied Power Electronics Conference and Exposition
- No. 10482334,p. 1544-1551
Analysis and Design of Voltage Regulator with Adaptive FET Modulation To Improve Efficiency
This paper presents a load adaptive voltage regulator that achieves high efficiency extended to light and heavy load regions. The presented method is named as "Adaptive FET Modulation" (AFM) since multiple FETs with different specifications are paralleled such that the number of driven FETs and their respective gate driving voltage are adaptive to load current. The capability of adaptive modulation of FETs' parasitic charges and resistances along with adaptive gate driving voltage allows achieving the best FET optimization over a wide load range. AFM operates at a fixed switching frequency for almost the whole load range, therefore it has no effect on the conventional buck operation and its dynamic performance, and is simple to implement. In this paper, the concept, design, analysis and experimental results of the proposed AFM are presented.
- 1 February 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in APEC 07 - Twenty-Second Annual IEEE Applied Power Electronics Conference and Exposition
- No. 10482334,p. 1544-1551
Analysis and Design of Voltage Regulator with Adaptive FET Modulation To Improve Efficiency
This paper presents a load adaptive voltage regulator that achieves high efficiency extended to light and heavy load regions. The presented method is named as "Adaptive FET Modulation" (AFM) since multiple FETs with different specifications are paralleled such that the number of driven FETs and their respective gate driving voltage are adaptive to load current. The capability of adaptive modulation of FETs' parasitic charges and resistances along with adaptive gate driving voltage allows achieving the best FET optimization over a wide load range. AFM operates at a fixed switching frequency for almost the whole load range, therefore it has no effect on the conventional buck operation and its dynamic performance, and is simple to implement. In this paper, the concept, design, analysis and experimental results of the proposed AFM are presented.
- 1 February 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in APEC 07 - Twenty-Second Annual IEEE Applied Power Electronics Conference and Exposition
- No. 10482334,p. 1568-1574
Adaptive Controller with Mode Tracking and Parametric Estimation
Digital controller algorithms are presented in this paper which allows detecting DCM and CCM operations without instantaneous or cycle by cycle sensing and sampling of inductor current. The presented control scheme also allows the estimation on output inductor value, the peak inductor current value and other information on converter operations. The objective is to estimate all of this information from the input current with low speed sensing without feeding any constants to the controller. The presented controller does not depend on sensing the input voltage, the load current, or any other information of the converter design. The presented algorithms are discussed and analyzed.
- 1 February 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in APEC 07 - Twenty-Second Annual IEEE Applied Power Electronics Conference and Exposition
- No. 10482334,p. 1568-1574
Adaptive Controller with Mode Tracking and Parametric Estimation
Digital controller algorithms are presented in this paper which allows detecting DCM and CCM operations without instantaneous or cycle by cycle sensing and sampling of inductor current. The presented control scheme also allows the estimation on output inductor value, the peak inductor current value and other information on converter operations. The objective is to estimate all of this information from the input current with low speed sensing without feeding any constants to the controller. The presented controller does not depend on sensing the input voltage, the load current, or any other information of the converter design. The presented algorithms are discussed and analyzed.
- 1 February 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in APEC 07 - Twenty-Second Annual IEEE Applied Power Electronics Conference and Exposition
- No. 10482334,p. 148-156
Novel Current Sharing Schemes for Multiphase Converters with Digital Controller Implementation
Multiphase converters require a current sharing loop to maintain equal or desired current sharing between phases or paralleled modules. Conventional current sharing schemes are based on sensing each phase current to provide the current information to the control loop. Such schemes have disadvantages including the fact that they operate to generate a pre-set sharing ratio that is independent of converter efficiency value, they are highly affected by the sensing accuracy of each phase, and they require large associated sensing circuitries and off-line calibration. In this paper, new efficiency based current sharing concepts and schemes are proposed and discussed to eliminate or reduce the disadvantages of conventional schemes. The proposed concepts are based on dynamically maximizing the efficiency (minimizing power losses) of the converter to achieve the optimum current sharing ratio. They also provide schemes that are independent of sensing accuracy and require a reduced number of sensors and associated circuitries. The proposed schemes can be used for current sharing as stand-alone designs or can be combined with conventional schemes to achieve online current sharing loop calibration. Digital controller implementation is presented utilizing flexibility and other advantages of digital controllers. Experimental results are presented to support the theoretical analysis.
- 1 February 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in APEC 07 - Twenty-Second Annual IEEE Applied Power Electronics Conference and Exposition
- No. 10482334,p. 148-156
Novel Current Sharing Schemes for Multiphase Converters with Digital Controller Implementation
Multiphase converters require a current sharing loop to maintain equal or desired current sharing between phases or paralleled modules. Conventional current sharing schemes are based on sensing each phase current to provide the current information to the control loop. Such schemes have disadvantages including the fact that they operate to generate a pre-set sharing ratio that is independent of converter efficiency value, they are highly affected by the sensing accuracy of each phase, and they require large associated sensing circuitries and off-line calibration. In this paper, new efficiency based current sharing concepts and schemes are proposed and discussed to eliminate or reduce the disadvantages of conventional schemes. The proposed concepts are based on dynamically maximizing the efficiency (minimizing power losses) of the converter to achieve the optimum current sharing ratio. They also provide schemes that are independent of sensing accuracy and require a reduced number of sensors and associated circuitries. The proposed schemes can be used for current sharing as stand-alone designs or can be combined with conventional schemes to achieve online current sharing loop calibration. Digital controller implementation is presented utilizing flexibility and other advantages of digital controllers. Experimental results are presented to support the theoretical analysis.
- 1 February 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in APEC 07 - Twenty-Second Annual IEEE Applied Power Electronics Conference and Exposition
- No. 10482334,p. 543-549
Highly Efficient VRM For Wide Load Range with Dynamic Non-Uniform Current Sharing
Multiphase converters are widely used especially in powering high-current loads. These converters are conventionally designed with symmetric phases and equal/uniform current sharing. This paper presents a multiphase VRM utilizing the concept of dynamic non-uniform current sharing between non-uniform phases. It is shown in this paper that high efficiency conversion can be achieved over wider load range with non-uniform phase design in multiphase converters and by utilizing the control scheme of dynamically varied non-uniform current sharing ratio between the interleaved phases. It is also shown that the proposed concept does not necessarily cause the increase in the size and cost of VRM design. The concept can be further expanded to the designs of other power stages such as AC-DC and PFC converters, bus converters and isolated or non-isolated converters. Theoretical and experimental results are provided in this paper, and they are compared with conventional symmetric designs with uniform current sharing.
- 1 February 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in APEC 07 - Twenty-Second Annual IEEE Applied Power Electronics Conference and Exposition
- No. 10482334,p. 543-549
Highly Efficient VRM For Wide Load Range with Dynamic Non-Uniform Current Sharing
Multiphase converters are widely used especially in powering high-current loads. These converters are conventionally designed with symmetric phases and equal/uniform current sharing. This paper presents a multiphase VRM utilizing the concept of dynamic non-uniform current sharing between non-uniform phases. It is shown in this paper that high efficiency conversion can be achieved over wider load range with non-uniform phase design in multiphase converters and by utilizing the control scheme of dynamically varied non-uniform current sharing ratio between the interleaved phases. It is also shown that the proposed concept does not necessarily cause the increase in the size and cost of VRM design. The concept can be further expanded to the designs of other power stages such as AC-DC and PFC converters, bus converters and isolated or non-isolated converters. Theoretical and experimental results are provided in this paper, and they are compared with conventional symmetric designs with uniform current sharing.
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02759306,p. 961-967
Analysis and Small Signal Modeling of a Non-Uniform Multiphase Buck Converter
This paper presents steady-state analysis and dynamic modeling of a non-uniform multiphase buck converter. This type of converter architecture has been reported previously in the literature with non-uniform phase design with the utilization of dynamic non-uniform current sharing and phase picking schemes in order to improve the power conversion efficiency over a wide load range. Since this scheme encounters the use of different current and possibly different inductor values for each phase, and/or different input voltages at the input of each phase, the impact on the steady-state and dynamic performance needs to be studied. This paper presents an initial analysis and small modeling study with discussion and experimental verification.
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02759306,p. 961-967
Analysis and Small Signal Modeling of a Non-Uniform Multiphase Buck Converter
This paper presents steady-state analysis and dynamic modeling of a non-uniform multiphase buck converter. This type of converter architecture has been reported previously in the literature with non-uniform phase design with the utilization of dynamic non-uniform current sharing and phase picking schemes in order to improve the power conversion efficiency over a wide load range. Since this scheme encounters the use of different current and possibly different inductor values for each phase, and/or different input voltages at the input of each phase, the impact on the steady-state and dynamic performance needs to be studied. This paper presents an initial analysis and small modeling study with discussion and experimental verification.
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02759306,p. 2029-2036
Sensorless Current Sharing Analysis and Scheme for Multiphase Converters
Current sharing control in multiphase converters is essential for stable and safe operation under variable conditions or applications. In conventional current sharing schemes, this requires the sensing and processing on each phase current through a current sharing/balancing controller, which adds complexity, size, and cost to the converter design. In most cases, conventional schemes are usually based on achieving a pre-set current sharing ratio between phases (usually equal current value among different phases), assuming that the phase design is known (or symmetric in the case of equal sharing ratio), which may not result in the optimum efficiency. The accuracy of achieving the pre-set current sharing ratio is sensitive to the current sensing accuracy in all phases, which requires careful and tedious calibration of sensing circuitries. In this paper, theoretical analysis results are presented to derive a sensor less current sharing method. The analysis is further expanded to reveal the boundary conditions that result in not achieving the desired current sharing ratio. The presented method is described and verified with experimental results from a proof of concept prototype based on digital controller implementation.
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02759306,p. 2029-2036
Sensorless Current Sharing Analysis and Scheme for Multiphase Converters
Current sharing control in multiphase converters is essential for stable and safe operation under variable conditions or applications. In conventional current sharing schemes, this requires the sensing and processing on each phase current through a current sharing/balancing controller, which adds complexity, size, and cost to the converter design. In most cases, conventional schemes are usually based on achieving a pre-set current sharing ratio between phases (usually equal current value among different phases), assuming that the phase design is known (or symmetric in the case of equal sharing ratio), which may not result in the optimum efficiency. The accuracy of achieving the pre-set current sharing ratio is sensitive to the current sensing accuracy in all phases, which requires careful and tedious calibration of sensing circuitries. In this paper, theoretical analysis results are presented to derive a sensor less current sharing method. The analysis is further expanded to reveal the boundary conditions that result in not achieving the desired current sharing ratio. The presented method is described and verified with experimental results from a proof of concept prototype based on digital controller implementation.
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 105-111
Variable- Step-Size Auto-Tuning Algorithm for Digital Power Converter with Variable-Switching-Frequency
This paper presents the analysis and implementation of a digital controller with adaptive auto- tuning algorithm that has a variable step size to track and detect the optimum switching frequency for a DC-DC converter. The algorithm is theoretically analyzed and developed based on buck DC-DC converter loss model and behavior and directed towered improving the convergence speed and accuracy of the adaptive loop by adjusting the converter switching frequency with variable step size. Simulation results are presented for the developed algorithm under variable conditions. Future experimental work is also discussed.
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 105-111
Variable- Step-Size Auto-Tuning Algorithm for Digital Power Converter with Variable-Switching-Frequency
This paper presents the analysis and implementation of a digital controller with adaptive auto- tuning algorithm that has a variable step size to track and detect the optimum switching frequency for a DC-DC converter. The algorithm is theoretically analyzed and developed based on buck DC-DC converter loss model and behavior and directed towered improving the convergence speed and accuracy of the adaptive loop by adjusting the converter switching frequency with variable step size. Simulation results are presented for the developed algorithm under variable conditions. Future experimental work is also discussed.
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02759306,p. 846-850
Design Considerations and Dynamic Technique for Digitally Controlled Variable Frequency DC-DC Converter
A dynamic algorithm to avoid limit cycle oscillation problems and to improve stability in digitally controlled power converters with variable switching frequency operation is presented in this paper. Employing Variable switching frequency at light loads is one way to improve the efficiency of DC-DC converters. However, varying the switching frequency digitally introduces additional considerations that do not exist in variable frequency analog controllers. In this paper a dynamic algorithm to maintain system stability and dynamics at different switching frequencies and to avoid limit cycle oscillation problems is discussed and experimentally verified.
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02759306,p. 846-850
Design Considerations and Dynamic Technique for Digitally Controlled Variable Frequency DC-DC Converter
A dynamic algorithm to avoid limit cycle oscillation problems and to improve stability in digitally controlled power converters with variable switching frequency operation is presented in this paper. Employing Variable switching frequency at light loads is one way to improve the efficiency of DC-DC converters. However, varying the switching frequency digitally introduces additional considerations that do not exist in variable frequency analog controllers. In this paper a dynamic algorithm to maintain system stability and dynamics at different switching frequencies and to avoid limit cycle oscillation problems is discussed and experimentally verified.