Ion Mitelea
Research Subjects
Research Interests
Ion Mitelea has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Corneliu Marius Crăciunescu
Department of Materials and Fabrication Engineering, Politehnica University Timisoara, Bulevardul Mihai Viteazul nr. 1, 300222 Timișoara, Romania
2 shared publications - Ilare Bordeasu
Department of Mechanical Machines, Equipment and Transports, Politehnica University Timisoara, Bulevardul Mihai Viteazul nr.1, 300222 Timisoara, Romania
2 shared publications - Ion-Dragoș Uțu
Department of Materials and Manufacturing Engineering, Faculty of Mechanical Engineering, Politehnica University Timişoara, Bv. Mihai Viteazu 1, 300222 Timisoara, Romania
2 shared publications Corneliu Marius Crăciunescu
Department of Materials and Manufacturing Engineering , Politehnica University Timisoara , Romania
1 shared publication- Octavian Oancă
Department of Mechanical Machines, Equipments and Transportation, Politehnica University of Timisoara, 300026 Timisoara, Romania
1 shared publication Olimpiu Karancsi
Timisoara, Romania
1 shared publication
Latest Publications
- 25 November 2017
- Published by Walter de Gruyter GmbH in International Journal of Materials Research
- Vol. 108 (12) , 1099-1102
Cavitation erosion of 17-4 PH stainless steels following sub-zero treatment
The effect of sub-zero treatment on 17-4 PH stainless steels is analysed based on ultrasonic cavitation experiments conducted on a vibratory machine with piezoceramic crystals. The results prove that the proposed treatment (solution treatment + sub-zero cooling + tempering), favours a reduction, by about 40%, of the mean depth of erosion, and mean depth erosion rate after 165 min of erosion by vibratory cavitation, compared to the solution treatment. The improvement of the cavitation erosion behaviour is explained based on hardness, metallographic and X-ray diffraction analysis.
- 25 November 2017
- Published by Walter de Gruyter GmbH in International Journal of Materials Research
- Vol. 108 (12) , 1099-1102
Cavitation erosion of 17-4 PH stainless steels following sub-zero treatment
The effect of sub-zero treatment on 17-4 PH stainless steels is analysed based on ultrasonic cavitation experiments conducted on a vibratory machine with piezoceramic crystals. The results prove that the proposed treatment (solution treatment + sub-zero cooling + tempering), favours a reduction, by about 40%, of the mean depth of erosion, and mean depth erosion rate after 165 min of erosion by vibratory cavitation, compared to the solution treatment. The improvement of the cavitation erosion behaviour is explained based on hardness, metallographic and X-ray diffraction analysis.
- 14 July 2017
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 59 (7-8) , 642-646
Microstructure characterization and corrosion testing of MAG pulsed duplex stainless steel welds
Duplex stainless steels are extremely attractive construction materials for their usage in intense aggressive environments. They offer numerous advantages compared to the austenitic stainless steels having an excellent behavior to pitting and cavernous corrosion, and a high resistance to stress cracking corrosion in chlorides media. However, their corrosion properties are largely dependent on the microstructural factors such as: the quantitative ratio of the two phases ferrite/austenite (F/A), the presence of intermetallic compounds and the distribution of the alloying elements between the ferrite and austenite. As a result of the thermal cycles experienced by the base metal without a post-weld heat treatment, the mechanical properties are significantly different in the heat affected zone and the deposited metal compared with the properties of the base metal. The present paper highlights the effect of the post-weld solution treatment in order to restore the balance between austenite and ferrite in the welded joint areas and also to limit undesirable precipitation of secondary phases with implications for increasing the corrosion resistance.
- 14 July 2017
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 59 (7-8) , 642-646
Microstructure characterization and corrosion testing of MAG pulsed duplex stainless steel welds
Duplex stainless steels are extremely attractive construction materials for their usage in intense aggressive environments. They offer numerous advantages compared to the austenitic stainless steels having an excellent behavior to pitting and cavernous corrosion, and a high resistance to stress cracking corrosion in chlorides media. However, their corrosion properties are largely dependent on the microstructural factors such as: the quantitative ratio of the two phases ferrite/austenite (F/A), the presence of intermetallic compounds and the distribution of the alloying elements between the ferrite and austenite. As a result of the thermal cycles experienced by the base metal without a post-weld heat treatment, the mechanical properties are significantly different in the heat affected zone and the deposited metal compared with the properties of the base metal. The present paper highlights the effect of the post-weld solution treatment in order to restore the balance between austenite and ferrite in the welded joint areas and also to limit undesirable precipitation of secondary phases with implications for increasing the corrosion resistance.
- 30 August 2016
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 58 (9) , 725-730
TIG deposition of Ti on steel substrates using Cu as interlayer
The deposition of Ti on steel substrates using a Cu interlayer was experimentally investigated using the tungsten inert gas technique with a mechanized feeding system. First, a Cu layer was deposited on the steel surface before the coating process for the production of the Ti layer. The resulting depositions exhibit a good penetration following the occurrence of two heat affected zones with a dense, compact and free-of-cracks microstructure. The investigations by scanning electron microscopy and by X-ray diffraction showed the formation of compounds in the Ti-Cu system and the absence of chemical combinations between Ti and Fe that can strongly affect the toughness characteristics of the deposited layer. The measurement of the cross-sectional hardness shows a significant increase in the surface compared to that of the substrate.
- 30 August 2016
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 58 (9) , 725-730
TIG deposition of Ti on steel substrates using Cu as interlayer
The deposition of Ti on steel substrates using a Cu interlayer was experimentally investigated using the tungsten inert gas technique with a mechanized feeding system. First, a Cu layer was deposited on the steel surface before the coating process for the production of the Ti layer. The resulting depositions exhibit a good penetration following the occurrence of two heat affected zones with a dense, compact and free-of-cracks microstructure. The investigations by scanning electron microscopy and by X-ray diffraction showed the formation of compounds in the Ti-Cu system and the absence of chemical combinations between Ti and Fe that can strongly affect the toughness characteristics of the deposited layer. The measurement of the cross-sectional hardness shows a significant increase in the surface compared to that of the substrate.
- Open Access
Cavitation Erosion of Cermet-Coated Aluminium Bronzes
The cavitation erosion resistance of CuAl10Ni5Fe2.5Mn1 following plasma spraying with Al2O3·30(Ni20Al) powder and laser re-melting was analyzed in view of possible improvements of the lifetime of components used in hydraulic environments. The cavitation erosion resistance was substantially improved compared with the one of the base material. The thickness of the re-melted layer was in the range of several hundred micrometers, with a surface microhardness increasing from 250 to 420 HV 0.2. Compositional, structural, and microstructural explorations showed that the microstructure of the re-melted and homogenized layer, consisting of a cubic Al2O3 matrix with dispersed Ni-based solid solution is associated with the hardness increase and consequently with the improvement of the cavitation erosion resistance.
Open AccessCavitation Erosion of Cermet-Coated Aluminium Bronzes
The cavitation erosion resistance of CuAl10Ni5Fe2.5Mn1 following plasma spraying with Al2O3·30(Ni20Al) powder and laser re-melting was analyzed in view of possible improvements of the lifetime of components used in hydraulic environments. The cavitation erosion resistance was substantially improved compared with the one of the base material. The thickness of the re-melted layer was in the range of several hundred micrometers, with a surface microhardness increasing from 250 to 420 HV 0.2. Compositional, structural, and microstructural explorations showed that the microstructure of the re-melted and homogenized layer, consisting of a cubic Al2O3 matrix with dispersed Ni-based solid solution is associated with the hardness increase and consequently with the improvement of the cavitation erosion resistance.