Rafał Wyczółkowski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Rafał Wyczółkowski has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Marek Gała
Institute of Electric Power Engineering, Czestochowa University of Technology, Armii Krajowej 17, 42-200 Czestochowa, Poland
6 shared publications - Vazgen Bagdasaryan
Institute of Civil Engineering, Warsaw University of Life Sciences-SGGW, Nowoursynowska 166, 02-787 Warsaw, Poland
6 shared publications - Dorota Musiał
Department of Production Management, Faculty of Production Engineering and Materials Technology, Czestochowa University of Technology, Armii Krajowej 19, 42-200 Czestochowa, Poland
4 shared publications D. Urbaniak
Czestochowa University of Technology, Czestochowa, Poland
2 shared publications- Dariusz Urbaniak
Częstochowa University of Technology
2 shared publications H. Otwinowski
Czestochowa University of Technology, 42-201 Czestochowa, Poland
2 shared publications
Latest Publications
- Open Access
- 23 August 2025
- Published by Polish Academy of Sciences Chancellery in Archive of Mechanical Engineering
- p. 473-484
Analysis of the influence of the heat transfer model on the effectiveness of the heat exchanger on the example of cross flow device
One of the methods of analyzing a heat exchanger consists in determining the heat transfer rates and outlet temperatures of the fluids for known mass flows, inlet temperatures, and exchanger type and size. This requires calculating the exchanger performance for known transfer surface area but unknown outlet temperatures. The concept of the heat transfer effectiveness (HTE) can be applied to determine the heat transfer rate of the specified heat exchanger without knowing the outlet temperatures of the fluids. This article presents the results of calculations of the HTE parameter for a cross-flow heat exchanger with staggered tube banks. The analysis takes into account six different models of convection heat transfer over the tube banks. In this scenario, the impact of the applied convection model on the value of HTE for the considered heat exchanger was examined. For the considered calculation cases, the value of the HTE parameter is in the range from 0.3 to 0.48 and it decreases with the increase of the flow rate of both air and the flue gases. It has been shown that the results of all four models are very similar, while the other two models bring about either an increase or a decrease of the values of the parameter investigated. It was found that for the analyzed heat exchanger a simplified criterion for the convection heat transfer over tube banks can be used to determine the effectiveness of the heat transfer with the Reynolds number being the only parameter.
- 23 August 2025
- Published by Polish Academy of Sciences Chancellery in Archive of Mechanical Engineering
- p. 473-484
Open AccessAnalysis of the influence of the heat transfer model on the effectiveness of the heat exchanger on the example of cross flow device
One of the methods of analyzing a heat exchanger consists in determining the heat transfer rates and outlet temperatures of the fluids for known mass flows, inlet temperatures, and exchanger type and size. This requires calculating the exchanger performance for known transfer surface area but unknown outlet temperatures. The concept of the heat transfer effectiveness (HTE) can be applied to determine the heat transfer rate of the specified heat exchanger without knowing the outlet temperatures of the fluids. This article presents the results of calculations of the HTE parameter for a cross-flow heat exchanger with staggered tube banks. The analysis takes into account six different models of convection heat transfer over the tube banks. In this scenario, the impact of the applied convection model on the value of HTE for the considered heat exchanger was examined. For the considered calculation cases, the value of the HTE parameter is in the range from 0.3 to 0.48 and it decreases with the increase of the flow rate of both air and the flue gases. It has been shown that the results of all four models are very similar, while the other two models bring about either an increase or a decrease of the values of the parameter investigated. It was found that for the analyzed heat exchanger a simplified criterion for the convection heat transfer over tube banks can be used to determine the effectiveness of the heat transfer with the Reynolds number being the only parameter.
- Open Access
Computational Model of the Effective Thermal Conductivity of a Bundle of Round Steel Bars
During the heat treatment of round steel bars, a heated charge in the form of a cylindrically formed bundle is placed in a furnace. This type of charge is a porous granular medium in which a complex heat flow occurs during heating. The following heat transfer mechanisms occur simultaneously in this medium: conduction in bars, conduction within the gas, thermal radiation between the surfaces of the bars, and contact conduction across the joints between the adjacent bars. This complex heat transfer can be quantified in terms of effective thermal conductivity. This article presents the original model of the effective thermal conductivity of a bundle of round steel bars. This model is based on the thermo-electric analogy. Each heat transfer mechanism is assigned an appropriate thermal resistance. As a result of the calculations, the impact of the following parameters on the intensity of heat transfer in the bundle was examined: temperature, the thermal conductivity of the bars, the thermal conductivity of the gas, diameter, and emissivity of the bar, and bundle porosity. Calculations were performed for a temperature range of 25–800 °C, covering a wide spectrum of variables, including bar diameters, bundle porosity, and type of gas. The knowledge obtained thanks to the calculations performed will facilitate the optimization of heat treatment processes for the considered charge. The greatest scientific value of the presented research is the demonstration that, thanks to the developed computational model, it is possible to analyze a very complex heat transfer phenomenon using relatively simple mathematical relationships.
Open AccessComputational Model of the Effective Thermal Conductivity of a Bundle of Round Steel Bars
During the heat treatment of round steel bars, a heated charge in the form of a cylindrically formed bundle is placed in a furnace. This type of charge is a porous granular medium in which a complex heat flow occurs during heating. The following heat transfer mechanisms occur simultaneously in this medium: conduction in bars, conduction within the gas, thermal radiation between the surfaces of the bars, and contact conduction across the joints between the adjacent bars. This complex heat transfer can be quantified in terms of effective thermal conductivity. This article presents the original model of the effective thermal conductivity of a bundle of round steel bars. This model is based on the thermo-electric analogy. Each heat transfer mechanism is assigned an appropriate thermal resistance. As a result of the calculations, the impact of the following parameters on the intensity of heat transfer in the bundle was examined: temperature, the thermal conductivity of the bars, the thermal conductivity of the gas, diameter, and emissivity of the bar, and bundle porosity. Calculations were performed for a temperature range of 25–800 °C, covering a wide spectrum of variables, including bar diameters, bundle porosity, and type of gas. The knowledge obtained thanks to the calculations performed will facilitate the optimization of heat treatment processes for the considered charge. The greatest scientific value of the presented research is the demonstration that, thanks to the developed computational model, it is possible to analyze a very complex heat transfer phenomenon using relatively simple mathematical relationships.
- Open Access
Qualitative Analysis of the Heat Transfer in a Package of Square Steel Sections
During the heat treatment of square or rectangular steel sections, a heated charge, arranged in regular packages, is placed inside a furnace. This type of charge forms a porous medium through which a complex heat flow occurs during heating. Several heat transfer mechanisms act simultaneously within this medium: conduction through the section walls, conduction and natural convection within the gas, thermal radiation between the section walls, and complex heat transfer (mainly contact conduction) at the joints between the adjacent sections. This article presents a qualitative analysis of heat transfer, aiming to determine the contribution of individual heat transfer mechanisms to the overall process. For this purpose, an analytical model of complex heat transfer within the package was employed, based on the thermo-electric analogy. The results from experimental studies were used to calculate the natural convection and heat transfer at the joints. It was assumed that the material of the sections was low-carbon steel, and the gas was air. Calculations were performed for the temperature range of 25 °C to 700 °C, considering three different geometrical configurations of the sections. It was shown that the effective thermal conductivity (ETC) of the package for the considered geometrical cases varies between 2.2 and 10.6 W/(m·K), which is an order of magnitude lower than the thermal conductivity of the individual sections. This parameter increased dynamically with the temperature. Moreover, the heat transfer intensity within the package of sections was nearly an order of magnitude lower than the heat conduction observed in a solid steel charge. Additionally, it was shown that the primary heat transfer mechanisms governing the heating process were thermal conduction (in the lower temperature range—up to approximately 350 °C) and thermal radiation (in the higher temperature range—above 350 °C). The gas convection inside the sections had a minimal impact on the heating process of the package. The primary parameters influencing the quality of the results were the joint resistance between the adjacent sections and the emissivity of the sections. The presented model can be used for the optimization of heat treatment processes for the considered charge.
Open AccessQualitative Analysis of the Heat Transfer in a Package of Square Steel Sections
During the heat treatment of square or rectangular steel sections, a heated charge, arranged in regular packages, is placed inside a furnace. This type of charge forms a porous medium through which a complex heat flow occurs during heating. Several heat transfer mechanisms act simultaneously within this medium: conduction through the section walls, conduction and natural convection within the gas, thermal radiation between the section walls, and complex heat transfer (mainly contact conduction) at the joints between the adjacent sections. This article presents a qualitative analysis of heat transfer, aiming to determine the contribution of individual heat transfer mechanisms to the overall process. For this purpose, an analytical model of complex heat transfer within the package was employed, based on the thermo-electric analogy. The results from experimental studies were used to calculate the natural convection and heat transfer at the joints. It was assumed that the material of the sections was low-carbon steel, and the gas was air. Calculations were performed for the temperature range of 25 °C to 700 °C, considering three different geometrical configurations of the sections. It was shown that the effective thermal conductivity (ETC) of the package for the considered geometrical cases varies between 2.2 and 10.6 W/(m·K), which is an order of magnitude lower than the thermal conductivity of the individual sections. This parameter increased dynamically with the temperature. Moreover, the heat transfer intensity within the package of sections was nearly an order of magnitude lower than the heat conduction observed in a solid steel charge. Additionally, it was shown that the primary heat transfer mechanisms governing the heating process were thermal conduction (in the lower temperature range—up to approximately 350 °C) and thermal radiation (in the higher temperature range—above 350 °C). The gas convection inside the sections had a minimal impact on the heating process of the package. The primary parameters influencing the quality of the results were the joint resistance between the adjacent sections and the emissivity of the sections. The presented model can be used for the optimization of heat treatment processes for the considered charge.
- Open Access
- 9 January 2024
- Published by Warsaw University of Life Sciences - SGGW Press in Acta Scientiarum Polonorum. Architectura
- Vol. 22, 148-158
A Comparative Study of Selected Models for Effective Thermal Conductivity
This paper conducts a comparative evaluation of 22 models focusing on the effective thermal conductivity of two-phase porous materials. Calculations were performed for each model across a range of solid-to-fluid thermal conductivity ratios, spanning from 1 to 15,000, and for two different porosities: 0.1 and 0.2. The study advocates the use of dimensionless charts that normalised solid thermal conductivity (ks) and effective thermal conductivity (kef) concerning fluid thermal conductivity (kf) for qualitative analysis. Employing this approach, the examined models were categorised into four fundamental groups. The latter portion of the paper compares selected models with experimental data. These experiments involved testing eight porous media samples in the form of packed steel bars, arranged in two configurations: staggered and in-line. The tests were conducted over a temperature range of 75–400°C, corresponding to ks-to-kf ratios ranging from 1,800 to 855. Various graphical representations were used to compare measurement data with model calculations. The findings indicate that the most accurate comparisons can be made using linear charts, which present absolute values of the kef coefficient in relation to the thermal conductivity of the solid phase.
- 9 January 2024
- Published by Warsaw University of Life Sciences - SGGW Press in Acta Scientiarum Polonorum. Architectura
- Vol. 22, 148-158
Open AccessA Comparative Study of Selected Models for Effective Thermal Conductivity
This paper conducts a comparative evaluation of 22 models focusing on the effective thermal conductivity of two-phase porous materials. Calculations were performed for each model across a range of solid-to-fluid thermal conductivity ratios, spanning from 1 to 15,000, and for two different porosities: 0.1 and 0.2. The study advocates the use of dimensionless charts that normalised solid thermal conductivity (ks) and effective thermal conductivity (kef) concerning fluid thermal conductivity (kf) for qualitative analysis. Employing this approach, the examined models were categorised into four fundamental groups. The latter portion of the paper compares selected models with experimental data. These experiments involved testing eight porous media samples in the form of packed steel bars, arranged in two configurations: staggered and in-line. The tests were conducted over a temperature range of 75–400°C, corresponding to ks-to-kf ratios ranging from 1,800 to 855. Various graphical representations were used to compare measurement data with model calculations. The findings indicate that the most accurate comparisons can be made using linear charts, which present absolute values of the kef coefficient in relation to the thermal conductivity of the solid phase.
- Open Access
Experimental and Theoretical Studies of the Thermal Contact Conductance for Bundles of Round Steel Bars
The paper presents investigations devoted to the analysis of the thermal contact conduction in a bundle of round steel bars. The phenomenon can be expressed quantitatively with the use of thermal contact conductance (hct). The starting points for the presented analysis were the results of the experimental measurements of the effective thermal conductivity. The measurements were performed for samples of a medium in the form of flat packed beds of bars with three different arrangements: staggered, in-line, and crossed and four bar diameters: 10, 20, 30, and 40 mm. Next, a mathematical model was developed, thanks to which the values of the hct coefficient were calculated for the analyzed cases. This approach consists in analyzing thermal resistances in the medium model, which is defined with an elementary cell. It was established that the value of the hct coefficient in the temperature range of 50–600 °C changes within the range of 50–175 W/(m2·K), and it decreases with an increase in the bar diameter. The final effect of the present study was to develop generalized approximation equations describing changes in thermal contact conductance in the heated bar bundle simultaneously in the temperature and bar diameter function.
Open AccessExperimental and Theoretical Studies of the Thermal Contact Conductance for Bundles of Round Steel Bars
The paper presents investigations devoted to the analysis of the thermal contact conduction in a bundle of round steel bars. The phenomenon can be expressed quantitatively with the use of thermal contact conductance (hct). The starting points for the presented analysis were the results of the experimental measurements of the effective thermal conductivity. The measurements were performed for samples of a medium in the form of flat packed beds of bars with three different arrangements: staggered, in-line, and crossed and four bar diameters: 10, 20, 30, and 40 mm. Next, a mathematical model was developed, thanks to which the values of the hct coefficient were calculated for the analyzed cases. This approach consists in analyzing thermal resistances in the medium model, which is defined with an elementary cell. It was established that the value of the hct coefficient in the temperature range of 50–600 °C changes within the range of 50–175 W/(m2·K), and it decreases with an increase in the bar diameter. The final effect of the present study was to develop generalized approximation equations describing changes in thermal contact conductance in the heated bar bundle simultaneously in the temperature and bar diameter function.
- 20 October 2022
- Published by Polish Academy of Sciences Chancellery in Archives of Thermodynamics
- Vol. 43 (3) , 29-45
Correlations for the thermal conductivity of selected steel grades as a function of temperature in the range of 0–800°C
Reliable knowledge of thermo-physical properties of materials is essential for the interpretation of solidification behaviour, forming, heat treatment and joining of metallic systems. It is also a precondition for precise simulation calculations of technological processes. Numerical calculations usually require the knowledge of temperature dependencies of three basic thermo-physical properties: thermal conductivity, heat capacity and density. The objective of this work is to find a correlation that fits the thermal conductivity of selected steel grades as a function of temperature (within the range of 0–800°C) and carbon content (within the range of 0.1–0.6%). The starting point for the analysis are the experimental data on thermal conductivity taken from literature. Using the method of least squares it was possible to fit an equation which allows calculating the thermal conductivity of steel depending on the temperature and carbon content. Two kinds of equations have been analyzed: a linear one (a linear model) and a second degree polynomial (a non-linear model). The thermal conductivity obtained by linear and nonlinear models varies on average from the measured values by 3% and 2.6% respectively.
- 20 October 2022
- Published by Polish Academy of Sciences Chancellery in Archives of Thermodynamics
- Vol. 43 (3) , 29-45
Correlations for the thermal conductivity of selected steel grades as a function of temperature in the range of 0–800°C
Reliable knowledge of thermo-physical properties of materials is essential for the interpretation of solidification behaviour, forming, heat treatment and joining of metallic systems. It is also a precondition for precise simulation calculations of technological processes. Numerical calculations usually require the knowledge of temperature dependencies of three basic thermo-physical properties: thermal conductivity, heat capacity and density. The objective of this work is to find a correlation that fits the thermal conductivity of selected steel grades as a function of temperature (within the range of 0–800°C) and carbon content (within the range of 0.1–0.6%). The starting point for the analysis are the experimental data on thermal conductivity taken from literature. Using the method of least squares it was possible to fit an equation which allows calculating the thermal conductivity of steel depending on the temperature and carbon content. Two kinds of equations have been analyzed: a linear one (a linear model) and a second degree polynomial (a non-linear model). The thermal conductivity obtained by linear and nonlinear models varies on average from the measured values by 3% and 2.6% respectively.
- Open Access
- 9 July 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (14) , 6977
Experimental Investigation of Thermal Contact Conductance in a Bundle of Flat Steel Bars
The phenomenon of thermal contact conduction in two-phase (fluid-solid) media determines many technological processes. An example of such a process is heat treatment of steel bars, when a heated charge has a form of a packed bundle. In order to determine the optimal heating curve it is necessary to have knowledge about the intensity of transfer through contact areas of the bars. This phenomenon is quantified by the thermal contact conductance hct. The article describes the methodology of determining the hct coefficient for bundles of flat steel bars. The starting point for the analysis is the measurement of the effective thermal conductivity kef performed for 5 × 20 mm and 10 × 20 mm bars. Individual samples of the same bars differed in arrangement. The analytical investigation used the concept of an elementary cell. This approach consisted in analysing resistances for individual heat transfer types: conduction, contact conduction and radiation. Based on the performed calculations it has been established that the value of the hct coefficient for the analysed samples is within the range 128–472 W/(m2 K). Changes of the hct coefficient in the temperature range 25–700 °C can be described with a second degree polynomial. It has been established that hct assumes maximum values in the temperature range from 300 °C to 400 °C.
- 9 July 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (14) , 6977
Open AccessExperimental Investigation of Thermal Contact Conductance in a Bundle of Flat Steel Bars
The phenomenon of thermal contact conduction in two-phase (fluid-solid) media determines many technological processes. An example of such a process is heat treatment of steel bars, when a heated charge has a form of a packed bundle. In order to determine the optimal heating curve it is necessary to have knowledge about the intensity of transfer through contact areas of the bars. This phenomenon is quantified by the thermal contact conductance hct. The article describes the methodology of determining the hct coefficient for bundles of flat steel bars. The starting point for the analysis is the measurement of the effective thermal conductivity kef performed for 5 × 20 mm and 10 × 20 mm bars. Individual samples of the same bars differed in arrangement. The analytical investigation used the concept of an elementary cell. This approach consisted in analysing resistances for individual heat transfer types: conduction, contact conduction and radiation. Based on the performed calculations it has been established that the value of the hct coefficient for the analysed samples is within the range 128–472 W/(m2 K). Changes of the hct coefficient in the temperature range 25–700 °C can be described with a second degree polynomial. It has been established that hct assumes maximum values in the temperature range from 300 °C to 400 °C.
- Open Access
The Review of Chosen Methods Used to Investigate Heat Transfer in a Steel Porous Charge
The paper presents chosen experimental and model methods of investigating heat transfer in a steel porous charge. The results of this investigation provide information on both the qualitative and quantitative course of the analysed processes of heat exchange. The parameters which characterise the analysed phenomenon in a quantitative manner, among others, are: The effective thermal conductivity kef, the thermal contact resistance Rct and Nusselt number Nu. It has been established that it is not possible to use literature models in order to determine the kef coefficient. The authors present their own model of effective thermal conductivity. The above-mentioned parameters for a porous charge reach the values within the following ranges: kef: 1.0–8.5 W/(m·K); Rct: 0.0019–0.0057 (m2⋅K)/W; Nu: 1.2–7.1.
Open AccessThe Review of Chosen Methods Used to Investigate Heat Transfer in a Steel Porous Charge
The paper presents chosen experimental and model methods of investigating heat transfer in a steel porous charge. The results of this investigation provide information on both the qualitative and quantitative course of the analysed processes of heat exchange. The parameters which characterise the analysed phenomenon in a quantitative manner, among others, are: The effective thermal conductivity kef, the thermal contact resistance Rct and Nusselt number Nu. It has been established that it is not possible to use literature models in order to determine the kef coefficient. The authors present their own model of effective thermal conductivity. The above-mentioned parameters for a porous charge reach the values within the following ranges: kef: 1.0–8.5 W/(m·K); Rct: 0.0019–0.0057 (m2⋅K)/W; Nu: 1.2–7.1.
- Open Access
Experimental Investigations of Effective Thermal Conductivity of the Selected Examples of Steel Porous Charge
In many cases of heat treatment of steel products, the heated charge has a porous structure. The examples of such charges include bundles of long steel components e.g., bars. The basic thermal property of the charge in this form is effective thermal conductivity kef. This paper presents the results of experimental examinations of effective thermal conductivity of the porous charge, which is composed from various types of steel long components. Due to the specific nature of the samples, a special measurement stand was constructed based on the design of a guarded hot plate apparatus. The measurements were performed for sixteen different samples across a temperature range of 70–640 °C. The porosity of the samples, depending on the type of components used, ranged from 0.03 to 0.85. Depending on these factors, the effective thermal conductivity ranged from 1.75 to 8.19 W·m−1·K−1. This accounts for 0.03 to 0.25 of the value of thermal conductivity of the solid phase of the charge, which in the described cases was low-carbon steel. It was found that the effective thermal conductivity rises linearly with temperature. The intensity of this increase and the value of coefficient kef depend on the transverse dimension of the components that form the charge. The results may represent the basis for the validation of various models of effective thermal conductivity with respect to the evaluation of thermal properties of the porous charge.
Open AccessExperimental Investigations of Effective Thermal Conductivity of the Selected Examples of Steel Porous Charge
In many cases of heat treatment of steel products, the heated charge has a porous structure. The examples of such charges include bundles of long steel components e.g., bars. The basic thermal property of the charge in this form is effective thermal conductivity kef. This paper presents the results of experimental examinations of effective thermal conductivity of the porous charge, which is composed from various types of steel long components. Due to the specific nature of the samples, a special measurement stand was constructed based on the design of a guarded hot plate apparatus. The measurements were performed for sixteen different samples across a temperature range of 70–640 °C. The porosity of the samples, depending on the type of components used, ranged from 0.03 to 0.85. Depending on these factors, the effective thermal conductivity ranged from 1.75 to 8.19 W·m−1·K−1. This accounts for 0.03 to 0.25 of the value of thermal conductivity of the solid phase of the charge, which in the described cases was low-carbon steel. It was found that the effective thermal conductivity rises linearly with temperature. The intensity of this increase and the value of coefficient kef depend on the transverse dimension of the components that form the charge. The results may represent the basis for the validation of various models of effective thermal conductivity with respect to the evaluation of thermal properties of the porous charge.
- Open Access
Determination of the Radiation Exchange Factor in the Bundle of Steel Round Bars
A method to obtain a radiation exchange factor FR in the bundle of steel round bars is presented. This parameter is required for determination of the radiative thermal conductivity krd, which is one of the basic thermal properties of the bar bundles. In the presented approach, the analyzed parameter is calculated indirectly. The initial point for calculations is the geometric model of the medium defined as a unit cell. Then, for the elements present in this cell, the thermal resistance of both conduction and radiation is determined. The radiation resistance is calculated from the radiosity balance of the surfaces enclosing the analyzed system. On this basis, the radiation thermal conductivity krd is calculated. Next, taking into account the bar diameter, the value of parameter FR is also determined. The analysis is performed at the process temperature range of 200 to 800 °C for three bar diameters: 10, 20 and 30 mm, and for the three porosities of the bundle. Different emissivity of bars in the range of 0.5 to 0.9 was also taken into account. Finally, a relationship that allows calculating the FR factor correlated with the emissivity of the bars and the bundle porosity was established. The krd obtained from the methodology presented and compared with the values calculated directly do not exceed 9%; however, after averaging over the entire temperature range of the process, the difference does not exceed 0.2%.
Open AccessDetermination of the Radiation Exchange Factor in the Bundle of Steel Round Bars
A method to obtain a radiation exchange factor FR in the bundle of steel round bars is presented. This parameter is required for determination of the radiative thermal conductivity krd, which is one of the basic thermal properties of the bar bundles. In the presented approach, the analyzed parameter is calculated indirectly. The initial point for calculations is the geometric model of the medium defined as a unit cell. Then, for the elements present in this cell, the thermal resistance of both conduction and radiation is determined. The radiation resistance is calculated from the radiosity balance of the surfaces enclosing the analyzed system. On this basis, the radiation thermal conductivity krd is calculated. Next, taking into account the bar diameter, the value of parameter FR is also determined. The analysis is performed at the process temperature range of 200 to 800 °C for three bar diameters: 10, 20 and 30 mm, and for the three porosities of the bundle. Different emissivity of bars in the range of 0.5 to 0.9 was also taken into account. Finally, a relationship that allows calculating the FR factor correlated with the emissivity of the bars and the bundle porosity was established. The krd obtained from the methodology presented and compared with the values calculated directly do not exceed 9%; however, after averaging over the entire temperature range of the process, the difference does not exceed 0.2%.