Mohd Warikh Abd Rashid
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohd Warikh Abd Rashid has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Noraiham Mohamad
Fakulti Teknologi dan Kejuruteraan Industri dan Pembuatan, Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Melaka, Malaysia
2 shared publications - Toibah Abd Rahim
Faculty of Industrial and Manufacturing Technology and Engineering, Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Melaka, Malaysia
2 shared publications - Toshihiro Moriga
Department of Chemical Science and Technology, Graduate School of Advanced Technology and Science, Tokushima University, 2-1 Minami-Josanjima, Tokushima, 770-8506 Japan
2 shared publications - Umar Al-Amani Azlan
Faculty of Industrial and Manufacturing Technology and Engineering, Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Melaka, Malaysia
2 shared publications - Ahmed Al-Ramthan
Faculty of Industrial and Manufacturing Technology and Engineering, Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Melaka, Malaysia
1 shared publication Effendi Mohamad
Faculty of Manufacturing Engineering, Universiti Teknikal Malaysia Melaka
1 shared publication
Latest Publications
- Open Access
- 28 February 2025
- Published by Akademia Baru Publishing in Journal of Advanced Research in Micro and Nano Engineering
- Vol. 30 (1) , 115-129
Effect of Forming Pressure on the Microstructure and Mechanical Characteristics of Dense Porous Ceramics
Ceramics are widely used in industrial applications due to their exceptional mechanical strength, thermal stability, and chemical resistance. However, the forming pressure during production significantly influences the microstructure and porosity, which in turn affect their mechanical properties. This study investigates the effects of varying forming pressures on the microstructure, porosity, and mechanical properties of dense porous ceramics, addressing the gap in understanding optimal forming conditions for enhanced performance. A composite of kaolinite clay, silica, feldspar, and carbon black as a pore-forming agent was uniaxially pressed at 10, 15, 20, 25, and 30 MPa and sintered at 1175°C for three hours. Microstructural analysis was conducted using field emission scanning electron microscopy, while density and flexural strength were measured using Archimedes’ principle and mechanical testing, respectively. Results reveal that flexural strength increased from 22.9404 MPa at 10 MPa to a peak of 29.5365 MPa at 20 MPa, followed by a decline at higher pressures due to potential microcrack formation. The optimal forming pressure of 20 MPa provides a balance between mechanical strength and controlled porosity, making it suitable for applications requiring structural integrity and permeability. These findings contribute to optimizing ceramic production processes for diverse industrial uses.
- 28 February 2025
- Published by Akademia Baru Publishing in Journal of Advanced Research in Micro and Nano Engineering
- Vol. 30 (1) , 115-129
Open AccessEffect of Forming Pressure on the Microstructure and Mechanical Characteristics of Dense Porous Ceramics
Ceramics are widely used in industrial applications due to their exceptional mechanical strength, thermal stability, and chemical resistance. However, the forming pressure during production significantly influences the microstructure and porosity, which in turn affect their mechanical properties. This study investigates the effects of varying forming pressures on the microstructure, porosity, and mechanical properties of dense porous ceramics, addressing the gap in understanding optimal forming conditions for enhanced performance. A composite of kaolinite clay, silica, feldspar, and carbon black as a pore-forming agent was uniaxially pressed at 10, 15, 20, 25, and 30 MPa and sintered at 1175°C for three hours. Microstructural analysis was conducted using field emission scanning electron microscopy, while density and flexural strength were measured using Archimedes’ principle and mechanical testing, respectively. Results reveal that flexural strength increased from 22.9404 MPa at 10 MPa to a peak of 29.5365 MPa at 20 MPa, followed by a decline at higher pressures due to potential microcrack formation. The optimal forming pressure of 20 MPa provides a balance between mechanical strength and controlled porosity, making it suitable for applications requiring structural integrity and permeability. These findings contribute to optimizing ceramic production processes for diverse industrial uses.
- Open Access
- 31 January 2025
- Published by Akademia Baru Publishing in Journal of Advanced Research in Micro and Nano Engineering
- Vol. 29 (1) , 36-45
Characterization on Structural and Electrical Properties of Manganese-doped Potassium Sodium Niobate (KNN) Thin Film by Sol-gel Method
The aim of this study is to create and examine thin layers of Mn-doped potassium sodium niobate (KNN) using the sol-gel method. The objective is to examine and resolve the problem of elevated leakage current density that arises at high electric fields in KNN films. The objective is to enhance the dielectric and ferroelectric characteristics by including manganese (Mn) dopants at various concentrations ranging from pure KNN to 0.9%, while maintaining acceptable insulation resistance. X-ray diffraction (XRD) was employed to investigate the crystalline structure of Mn-doped KNN thin films. Based on the XRD analysis, the Mn-doped KNN thin films exhibit an orthorhombic crystal structure during manufacture. The presence of KNN thin films is confirmed by the XRD peaks, indicating a successful synthesis. The microstructure and surface morphology of the thin films were examined using field-emission scanning electron microscopy (FESEM). The most significant outcomes in terms of dense grain growth and uniform grain size were observed in thin films of KNN doped with 0.3% Mn. Based on the findings from the FESEM and AFM, the cracks were covered with thin films of uniform thickness, and the surface data of the KNN thin films did not provide any support for them. Atomic Force Microscopy (AFM) and Piezoresponse Force Microscopy (PFM) analysis indicate a notable enhancement in the surface morphology and the value of the piezoelectric coefficient in Mn-doped KNN thin films, with an increase of 0.3%.
- 31 January 2025
- Published by Akademia Baru Publishing in Journal of Advanced Research in Micro and Nano Engineering
- Vol. 29 (1) , 36-45
Open AccessCharacterization on Structural and Electrical Properties of Manganese-doped Potassium Sodium Niobate (KNN) Thin Film by Sol-gel Method
The aim of this study is to create and examine thin layers of Mn-doped potassium sodium niobate (KNN) using the sol-gel method. The objective is to examine and resolve the problem of elevated leakage current density that arises at high electric fields in KNN films. The objective is to enhance the dielectric and ferroelectric characteristics by including manganese (Mn) dopants at various concentrations ranging from pure KNN to 0.9%, while maintaining acceptable insulation resistance. X-ray diffraction (XRD) was employed to investigate the crystalline structure of Mn-doped KNN thin films. Based on the XRD analysis, the Mn-doped KNN thin films exhibit an orthorhombic crystal structure during manufacture. The presence of KNN thin films is confirmed by the XRD peaks, indicating a successful synthesis. The microstructure and surface morphology of the thin films were examined using field-emission scanning electron microscopy (FESEM). The most significant outcomes in terms of dense grain growth and uniform grain size were observed in thin films of KNN doped with 0.3% Mn. Based on the findings from the FESEM and AFM, the cracks were covered with thin films of uniform thickness, and the surface data of the KNN thin films did not provide any support for them. Atomic Force Microscopy (AFM) and Piezoresponse Force Microscopy (PFM) analysis indicate a notable enhancement in the surface morphology and the value of the piezoelectric coefficient in Mn-doped KNN thin films, with an increase of 0.3%.
- Open Access
- 30 November 2024
- Published by Akademia Baru Publishing in Journal of Advanced Research in Micro and Nano Engineering
- Vol. 26 (1) , 30-43
Influence of Accelerators and Filler Content on Physical Properties of Tin Dioxide Reinforced Deproteinized Natural Rubber Nanocomposites
The global electrical industry is looking for sustainable materials in various domains, including electrical insulation cable materials. Tin dioxide (SnO2) nanoparticles combined with deproteinized natural rubber (DPNR) have the potential to produce an excellent and green electrical insulation material that combines their parents’ electrical properties. Yet, the processability is highly influenced by the curing system. The cure characteristics of rubber nanocomposites were investigated for the influence of different accelerators and SnO2 content. The 2,20-dithiobis (benzothiazole) (MBTS)-cured compounds exhibit ultrafast curing and higher melt viscosity than the N-Cyclohexyl-2-benzothiazole sulphonamide (CBS)-cured nanocomposite compounds, regardless of the increment in SnO2 loadings. Therefore, CBS-cured nanocomposites exhibit acceptable process safety, good processability and properties. The morphological, thermal and compositional analyses further supported the density, swelling behaviour and hardness of the DPNR nanocomposites of the selected accelerator system.
- 30 November 2024
- Published by Akademia Baru Publishing in Journal of Advanced Research in Micro and Nano Engineering
- Vol. 26 (1) , 30-43
Open AccessInfluence of Accelerators and Filler Content on Physical Properties of Tin Dioxide Reinforced Deproteinized Natural Rubber Nanocomposites
The global electrical industry is looking for sustainable materials in various domains, including electrical insulation cable materials. Tin dioxide (SnO2) nanoparticles combined with deproteinized natural rubber (DPNR) have the potential to produce an excellent and green electrical insulation material that combines their parents’ electrical properties. Yet, the processability is highly influenced by the curing system. The cure characteristics of rubber nanocomposites were investigated for the influence of different accelerators and SnO2 content. The 2,20-dithiobis (benzothiazole) (MBTS)-cured compounds exhibit ultrafast curing and higher melt viscosity than the N-Cyclohexyl-2-benzothiazole sulphonamide (CBS)-cured nanocomposite compounds, regardless of the increment in SnO2 loadings. Therefore, CBS-cured nanocomposites exhibit acceptable process safety, good processability and properties. The morphological, thermal and compositional analyses further supported the density, swelling behaviour and hardness of the DPNR nanocomposites of the selected accelerator system.
- Open Access
- 31 October 2024
- Published by Akademia Baru Publishing in Journal of Advanced Research in Micro and Nano Engineering
- Vol. 24 (1) , 46-51
Synthesis of Ni Nanoparticle with Controlled Morphology via Liquid Phase Reduction Method
This research focuses on the synthesis of nickel nanoparticles using liquid-phase reduction method, a cost-effective and scalable approach. It is discovered that the size and the morphology of the nickel nanoparticle can be control by varying the nickel ion concentration, reaction temperature as well as the pH of the solution. The results showed that the size of the nickel nanoparticles decreased with an increase of the nickel ion concentration. The results also indicate that the morphology of the nickel product strongly depend on the pH of the reaction solution. Nickel nanowires were observed at lower pH levels, while nickel nanoparticles with urchin-like particles were produced at higher pH levels. Henceforth, it will be possible to precisely change the synthesis parameters (nickel ion concentration, pH value and reaction temperature) to easily modify the morphology of the nickel nanoparticles. This research contributes valuable insights into the synthesis of well-defined nickel nanoparticles, opening avenues for their application in nanotechnology.
- 31 October 2024
- Published by Akademia Baru Publishing in Journal of Advanced Research in Micro and Nano Engineering
- Vol. 24 (1) , 46-51
Open AccessSynthesis of Ni Nanoparticle with Controlled Morphology via Liquid Phase Reduction Method
This research focuses on the synthesis of nickel nanoparticles using liquid-phase reduction method, a cost-effective and scalable approach. It is discovered that the size and the morphology of the nickel nanoparticle can be control by varying the nickel ion concentration, reaction temperature as well as the pH of the solution. The results showed that the size of the nickel nanoparticles decreased with an increase of the nickel ion concentration. The results also indicate that the morphology of the nickel product strongly depend on the pH of the reaction solution. Nickel nanowires were observed at lower pH levels, while nickel nanoparticles with urchin-like particles were produced at higher pH levels. Henceforth, it will be possible to precisely change the synthesis parameters (nickel ion concentration, pH value and reaction temperature) to easily modify the morphology of the nickel nanoparticles. This research contributes valuable insights into the synthesis of well-defined nickel nanoparticles, opening avenues for their application in nanotechnology.
- Open Access
- 1 January 2023
- Published by American Institute of Mathematical Sciences (AIMS) in AIMS Materials Science
- Vol. 10 (5) , 835-861
Potassium sodium niobate (KNN) lead-free piezoceramics: A review of phase boundary engineering based on KNN materials
Lead zirconia titanate (PZT) is the most often used piezoelectric material in various electronic applications like energy harvesters, ultrasonic capacitors and motors. It is true that PZT has a lot of significant drawbacks due to its 60% lead content, despite its outstanding ferroelectric, dielectric and piezoelectric properties which influenced by PZT's morphotropic phase boundary. The recently found potassium sodium niobate (KNN) is one of the most promising candidates for a new lead-free piezoelectric material. For the purpose of providing a resource and shedding light on the future, this paper provides a summary of the historical development of different phase boundaries in KNN materials and provides some guidance on how to achieve piezoelectric activity on par with PZT through a thorough examination and critical analysis of relevant articles by providing insight and perspective of KNN, which consists of detailed evaluation of the design, construction of phase boundaries and engineering for applications.
- 1 January 2023
- Published by American Institute of Mathematical Sciences (AIMS) in AIMS Materials Science
- Vol. 10 (5) , 835-861
Open AccessPotassium sodium niobate (KNN) lead-free piezoceramics: A review of phase boundary engineering based on KNN materials
Lead zirconia titanate (PZT) is the most often used piezoelectric material in various electronic applications like energy harvesters, ultrasonic capacitors and motors. It is true that PZT has a lot of significant drawbacks due to its 60% lead content, despite its outstanding ferroelectric, dielectric and piezoelectric properties which influenced by PZT's morphotropic phase boundary. The recently found potassium sodium niobate (KNN) is one of the most promising candidates for a new lead-free piezoelectric material. For the purpose of providing a resource and shedding light on the future, this paper provides a summary of the historical development of different phase boundaries in KNN materials and provides some guidance on how to achieve piezoelectric activity on par with PZT through a thorough examination and critical analysis of relevant articles by providing insight and perspective of KNN, which consists of detailed evaluation of the design, construction of phase boundaries and engineering for applications.
- 6 February 2019
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2068 (1) , 020093
Effect of palm oil fuel ash treatment on physico-mechanical properties of porcelain
Palm oil waste or palm oil fuel ash (POFA) has substantial value, it is used as fuels in the palm oil industries to heat the boiler and produce steam for electricity. The research aim is to determine the influences of temperature and treatment of POFA on the production of porcelain. POFA was dried in an oven for 24 hours at 110 °C, and then ground in a ball mill for 12 hours at 250 rev/sec. POFA was heat treated at 800 °C for 2 hours soaking time. 2 molar HCl acid was used to wash the other portion of POFA and dried again to remove the moisture. The POFA powder undergoes for X-ray fluorescence (XRF) analysis. Quartz was replaced with untreated and treated POFA at 15 wt% and mixed with others porcelain composition. The mixture powder was pelleted with pressure at 91 MPa and sintered at 1150 °C, 1200 °C and 1250 °C by using 2 hours soaking time, respectively. Then the samples undergo the density and compressive strength testing. XRF analysis results show that the major chemical composition of POFA is SiO2. The bulk density and compressive strength were obtained with the value of 2.424 g/cm3 and 153.02 MPa, respectively. SEM results show an enhanced densification with XRD major phases as quartz and mullite.
- 6 February 2019
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2068 (1) , 020093
Effect of palm oil fuel ash treatment on physico-mechanical properties of porcelain
Palm oil waste or palm oil fuel ash (POFA) has substantial value, it is used as fuels in the palm oil industries to heat the boiler and produce steam for electricity. The research aim is to determine the influences of temperature and treatment of POFA on the production of porcelain. POFA was dried in an oven for 24 hours at 110 °C, and then ground in a ball mill for 12 hours at 250 rev/sec. POFA was heat treated at 800 °C for 2 hours soaking time. 2 molar HCl acid was used to wash the other portion of POFA and dried again to remove the moisture. The POFA powder undergoes for X-ray fluorescence (XRF) analysis. Quartz was replaced with untreated and treated POFA at 15 wt% and mixed with others porcelain composition. The mixture powder was pelleted with pressure at 91 MPa and sintered at 1150 °C, 1200 °C and 1250 °C by using 2 hours soaking time, respectively. Then the samples undergo the density and compressive strength testing. XRF analysis results show that the major chemical composition of POFA is SiO2. The bulk density and compressive strength were obtained with the value of 2.424 g/cm3 and 153.02 MPa, respectively. SEM results show an enhanced densification with XRD major phases as quartz and mullite.
- Open Access
- 14 August 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 226 (1) , 012154
Sol gel synthesis and characterization studies of Cupromanganite CaCu3Mn4O12
A single-phase CaCu3Mn4O12 electroceramic had been prepared via sol gel method and fairly well densified at relative low temperature under atmospheric condition where the crystallization of CaCu3Mn4O12 occurred due to amorphous polymeric mixture. The precursor was prepared by mixing the solutions with 0.6 M citric acid (C6H8O7) as a chelating reagent with the mol ratio 1:2. The precursor gel formed was calcined and sintered at range 400 °C to 800°C by varying dwell time. Material formations under the reported conditions have been confirmed by X-ray diffraction (XRD). The results show that the formation of CaCu3Mn4O12 started at 500 ° C and was formed completely at 700 ° C for 18 hours. The microstructure of all CaCu3Mn4O12 was analysed using field emission scanning electron microscopy (FESEM). A smaller particle size with higher grain boundary was obtained at sintering 700°C to 800°C. FESEM results show the significant influence of calcinations and sintering parameter on the microstructure behaviour of CaCu2Mn4O12.
- 14 August 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 226 (1) , 012154
Open AccessSol gel synthesis and characterization studies of Cupromanganite CaCu3Mn4O12
A single-phase CaCu3Mn4O12 electroceramic had been prepared via sol gel method and fairly well densified at relative low temperature under atmospheric condition where the crystallization of CaCu3Mn4O12 occurred due to amorphous polymeric mixture. The precursor was prepared by mixing the solutions with 0.6 M citric acid (C6H8O7) as a chelating reagent with the mol ratio 1:2. The precursor gel formed was calcined and sintered at range 400 °C to 800°C by varying dwell time. Material formations under the reported conditions have been confirmed by X-ray diffraction (XRD). The results show that the formation of CaCu3Mn4O12 started at 500 ° C and was formed completely at 700 ° C for 18 hours. The microstructure of all CaCu3Mn4O12 was analysed using field emission scanning electron microscopy (FESEM). A smaller particle size with higher grain boundary was obtained at sintering 700°C to 800°C. FESEM results show the significant influence of calcinations and sintering parameter on the microstructure behaviour of CaCu2Mn4O12.
- 10 May 2016
- Published by Springer Nature in Journal of Electroceramics
- Vol. 37 (1-4) , 50-57
Structural evolution and dopant occupancy preference of yttrium-doped potassium sodium niobate thin films
- 10 May 2016
- Published by Springer Nature in Journal of Electroceramics
- Vol. 37 (1-4) , 50-57
Structural evolution and dopant occupancy preference of yttrium-doped potassium sodium niobate thin films
- Open Access
- 1 January 2014
- Published by Japan Society of Mechanical Engineers in The Proceedings of Design & Systems Conference
- Vol. 2014.24, _2301-1_
2301 A Review : The Potential of Powder Metallurgy in Recycling Aluminum Chips (Al 6061&Al 7075)
Aluminum products are becoming popular and the demand is increasing because of its special properties such as excellent corrosion resistance with good strength, recyclable and low density compared to steel. Currently, two methods used to recycle aluminum chips are conventional and direct conversion methods. Recycling of aluminum chips by the direct conversion methods is relatively simple, consumed less energy and do not harm the environment. The cost of recycled materials is much lower than the cost of primary aluminum production by conventional technique. This paper reviews the recycling technologies of aluminum chips using powder retallurgy technique.
- 1 January 2014
- Published by Japan Society of Mechanical Engineers in The Proceedings of Design & Systems Conference
- Vol. 2014.24, _2301-1_
Open Access2301 A Review : The Potential of Powder Metallurgy in Recycling Aluminum Chips (Al 6061&Al 7075)
Aluminum products are becoming popular and the demand is increasing because of its special properties such as excellent corrosion resistance with good strength, recyclable and low density compared to steel. Currently, two methods used to recycle aluminum chips are conventional and direct conversion methods. Recycling of aluminum chips by the direct conversion methods is relatively simple, consumed less energy and do not harm the environment. The cost of recycled materials is much lower than the cost of primary aluminum production by conventional technique. This paper reviews the recycling technologies of aluminum chips using powder retallurgy technique.