Dan Barnard
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Interests
Dan Barnard has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Richard Livings
Aerospace Engineering, Iowa State University, Ames, USA
4 shared publications - Vinay Dayal
Iowa State University
4 shared publications N. Poonthottathil
Department of Physics and Astronomy, Iowa State University, Ames, IA 50010
2 shared publications- A. J. R. Weinstein
Iowa State University
1 shared publication A. Weinstein
1 shared publicationAaron Herman
Center for Nondestructive Evaluation, Iowa State University, 1915 Scholl Road, Ames, IA 50011-3042, USA
1 shared publication
Latest Publications
- 19 January 2021
- Published by ASME International in Journal of Nondestructive Evaluation, Diagnostics and Prognostics of Engineering Systems
- Vol. 4 (2)
Inspection of Electronics Components for Cryogenic Temperature Operations
Electronics operating at cryogenic temperatures play a critical role in future science experiments and space exploration programs. The Deep Underground Neutrino Experiment (DUNE) uses a cold electronics system for data taking. Specifically, it utilizes custom-designed Application Specific Integrated Circuits (ASICs). The main challenge is that these circuits will be immersed in liquid Argon and that they need to function for 20+ years without any access. Ensuring quality is critical, and issues may arise due to thermal stress, packaging, and manufacturing-related defects: if undetected, these could lead to long-term reliability and performance problems. This paper reports an investigation into non-destructive evaluation techniques to assess their potential use in a comprehensive quality control process during prototyping, testing, and commissioning of the DUNE cold electronics system. Scanning acoustic microscopy (SAM) was used to investigate permanent structural changes in the ASICs associated with thermal cycling between room and cryogenic temperatures. Data are assessed using a correlation analysis, which can detect even minimal changes happening inside the ASICs.
- 19 January 2021
- Published by ASME International in Journal of Nondestructive Evaluation, Diagnostics and Prognostics of Engineering Systems
- Vol. 4 (2)
Inspection of Electronics Components for Cryogenic Temperature Operations
Electronics operating at cryogenic temperatures play a critical role in future science experiments and space exploration programs. The Deep Underground Neutrino Experiment (DUNE) uses a cold electronics system for data taking. Specifically, it utilizes custom-designed Application Specific Integrated Circuits (ASICs). The main challenge is that these circuits will be immersed in liquid Argon and that they need to function for 20+ years without any access. Ensuring quality is critical, and issues may arise due to thermal stress, packaging, and manufacturing-related defects: if undetected, these could lead to long-term reliability and performance problems. This paper reports an investigation into non-destructive evaluation techniques to assess their potential use in a comprehensive quality control process during prototyping, testing, and commissioning of the DUNE cold electronics system. Scanning acoustic microscopy (SAM) was used to investigate permanent structural changes in the ASICs associated with thermal cycling between room and cryogenic temperatures. Data are assessed using a correlation analysis, which can detect even minimal changes happening inside the ASICs.
- Open Access
Reliability studies of electronic components for the operation at cryogenic temperature
Cold electronics is a key technology in many areas of science and technology including space exploration programs and particle physics. A major experiment with a very large number of analog and digital electronics signal processing channels to be operated at cryogenic temperatures is the next-generation neutrino experiment, the Deep Underground Neutrino Experiment (DUNE). The DUNE detector uses liquid Argon at 87K as a target material for neutrinos, and as a medium to track charged particles resulting from interactions in the detector volume. The DUNE electronics [1] consists of custom-designed ASIC (Application Specific Integrated Circuits) chips based on low power 180 nm-CMOS technology. The main risk for this technology is that the electronics components will be immersed in liquid argon for many years (20-30 years) without access. Reliability issues of ASICs may arise from thermal stress, packaging, and manufacturing-related defects: if undetected those could lead to long-term reliability and performance problems. The scope of this paper is to explore non-destructive evaluation techniques for their potential use in a comprehensive quality control process during prototyping, testing and commissioning of the DUNE cold electronics system. Specifically, we have used the Scanning Acoustic Microscopy and X-ray tomography to study permanent structural changes in the ASIC chips associated with thermal cycling between the room and cryogenic temperatures.
Open AccessReliability studies of electronic components for the operation at cryogenic temperature
Cold electronics is a key technology in many areas of science and technology including space exploration programs and particle physics. A major experiment with a very large number of analog and digital electronics signal processing channels to be operated at cryogenic temperatures is the next-generation neutrino experiment, the Deep Underground Neutrino Experiment (DUNE). The DUNE detector uses liquid Argon at 87K as a target material for neutrinos, and as a medium to track charged particles resulting from interactions in the detector volume. The DUNE electronics [1] consists of custom-designed ASIC (Application Specific Integrated Circuits) chips based on low power 180 nm-CMOS technology. The main risk for this technology is that the electronics components will be immersed in liquid argon for many years (20-30 years) without access. Reliability issues of ASICs may arise from thermal stress, packaging, and manufacturing-related defects: if undetected those could lead to long-term reliability and performance problems. The scope of this paper is to explore non-destructive evaluation techniques for their potential use in a comprehensive quality control process during prototyping, testing and commissioning of the DUNE cold electronics system. Specifically, we have used the Scanning Acoustic Microscopy and X-ray tomography to study permanent structural changes in the ASIC chips associated with thermal cycling between the room and cryogenic temperatures.
- 10 February 2017
- Published by Springer Nature in Journal of Nondestructive Evaluation
- Vol. 36 (1) , 1-11
Air-Coupled Ultrasonic Resonance Imaging of Hexagonal SiC and Alumina Tiles
- 10 February 2017
- Published by Springer Nature in Journal of Nondestructive Evaluation
- Vol. 36 (1) , 1-11
Air-Coupled Ultrasonic Resonance Imaging of Hexagonal SiC and Alumina Tiles
- 12 September 2016
- Published by Springer Nature in Journal of Nondestructive Evaluation
- Vol. 35 (4) , 1-9
Damage Detection in a Multi-Layered, Multi-Material Composite Using Air-Coupled Ultrasonic Resonance Imaging
- 12 September 2016
- Published by Springer Nature in Journal of Nondestructive Evaluation
- Vol. 35 (4) , 1-9
Damage Detection in a Multi-Layered, Multi-Material Composite Using Air-Coupled Ultrasonic Resonance Imaging
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1706, 120003
Coda wave interferometry for the measurement of thermally induced ultrasonic velocity variations in CFRP laminates
Ultrasonic velocity measurement is a well-established method to measure properties and estimate strength as well as detect and locate damage. Determination of accurate and repeatable ultrasonic wave velocities can be difficult due to the influence of environmental and experimental factors. Diffuse fields created by a multiple scattering environment have been shown to be sensitive to homogeneous strain fields such as those caused by temperature variations, and Coda Wave Interferometry has been used to measure the thermally induced ultrasonic velocity variation in concrete, aluminum, and the Earth’s crust. In this work, we analyzed the influence of several parameters of the experimental configuration on the measurement of thermally induced ultrasonic velocity variations in a carbon-fiber reinforced polymer plate. Coda Wave Interferometry was used to determine the relative velocity change between a baseline signal taken at room temperature and the signal taken at various temperatures. The influence of several parameters of the experimental configuration, such as the material type, the receiver aperture size, and fiber orientation on the results of the processing algorithm was evaluated in order to determine the optimal experimental configuration.---This work is supported by the NSF Industry/University Cooperative Research Program of the Center for Nondestructive Evaluation at Iowa State University.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1706, 120003
Coda wave interferometry for the measurement of thermally induced ultrasonic velocity variations in CFRP laminates
Ultrasonic velocity measurement is a well-established method to measure properties and estimate strength as well as detect and locate damage. Determination of accurate and repeatable ultrasonic wave velocities can be difficult due to the influence of environmental and experimental factors. Diffuse fields created by a multiple scattering environment have been shown to be sensitive to homogeneous strain fields such as those caused by temperature variations, and Coda Wave Interferometry has been used to measure the thermally induced ultrasonic velocity variation in concrete, aluminum, and the Earth’s crust. In this work, we analyzed the influence of several parameters of the experimental configuration on the measurement of thermally induced ultrasonic velocity variations in a carbon-fiber reinforced polymer plate. Coda Wave Interferometry was used to determine the relative velocity change between a baseline signal taken at room temperature and the signal taken at various temperatures. The influence of several parameters of the experimental configuration, such as the material type, the receiver aperture size, and fiber orientation on the results of the processing algorithm was evaluated in order to determine the optimal experimental configuration.---This work is supported by the NSF Industry/University Cooperative Research Program of the Center for Nondestructive Evaluation at Iowa State University.
- 1 January 2015
- Published by AIP Publishing in AIP Conference Proceedings
Characterization of 3D rapid prototyped polymeric material by ultrasonic methods
Rapid prototyped parts are quickly becoming a viable alternative for manufacturers. Although the polymeric material is initially isotropic, the printing process introduces a level of anisotropy. This work characterizes the elastic and acoustic properties of the material, after printing, using ultrasonic methods. The elastic constants and the level of anisotropy are determined by measuring the ultrasonic wave velocities. It is shown that the material possesses less symmetry than the orthotropic material model. The dispersion and attenuation characteristics are also determined to provide a basis for ultrasonic flaw detection.
- 1 January 2015
- Published by AIP Publishing in AIP Conference Proceedings
Characterization of 3D rapid prototyped polymeric material by ultrasonic methods
Rapid prototyped parts are quickly becoming a viable alternative for manufacturers. Although the polymeric material is initially isotropic, the printing process introduces a level of anisotropy. This work characterizes the elastic and acoustic properties of the material, after printing, using ultrasonic methods. The elastic constants and the level of anisotropy are determined by measuring the ultrasonic wave velocities. It is shown that the material possesses less symmetry than the orthotropic material model. The dispersion and attenuation characteristics are also determined to provide a basis for ultrasonic flaw detection.
- 1 January 2015
- Published by AIP Publishing in AIP Conference Proceedings
NDE of transparent protective panels
In this paper we discuss nondestructive testing of five varieties of transparent armor panels fabricated from layers of glass, polymer and adhesive. The emphasis is on characterizing fabrication anomalies, such as lack of uniform layer thickness, rather than on damage detection. We report measurements of sound speed and attenuation on single-layer specimens of the polymer and the two types of glass used in the panels. We then discuss the results of various nondestructive studies of the panels, beginning with 225 KHz air-coupled ultrasonic testing (ACUT) and 5-MHz ultrasonic immersion testing. For all panels ultrasonic through-transmission C-scans reveal interesting patterns of signal amplitude and time-of-flight variations. These are traced to lateral changes in adhesive thickness within the panels. For one panel, adhesive sound speed, attenuation and density are deduced by analyzing UT immersion pulse/echo and pitch/catch data. Adhesive thickness variations manifest themselves differently in the two types of ultrasonic inspections. At the immersion inspection frequency adhesive attenuation dominates, so regions with thicker adhesive always have the smallest through-transmitted response. At ACUT frequencies reverberation echoes within the adhesive layer superimpose with echoes from other sound paths, and an increase in adhesive thickness can result in either an increase or decrease in through-transmitted amplitude. A simple model to account for such signal superposition is developed and found to be in qualitative agreement with the results of the ACUT inspections. The adhesive thickness variations cause the surfaces within the panel to be non-planar, leading to stresses on the various layers. We demonstrate the use of Terahertz-ray (T-ray) electromagnetic inspection to map the surface undulations of the thin glass outer layer in one of the panels. Bending stresses are estimated from the undulations and, at some locations, found to be at or near the levels that would cause fracture.
- 1 January 2015
- Published by AIP Publishing in AIP Conference Proceedings
NDE of transparent protective panels
In this paper we discuss nondestructive testing of five varieties of transparent armor panels fabricated from layers of glass, polymer and adhesive. The emphasis is on characterizing fabrication anomalies, such as lack of uniform layer thickness, rather than on damage detection. We report measurements of sound speed and attenuation on single-layer specimens of the polymer and the two types of glass used in the panels. We then discuss the results of various nondestructive studies of the panels, beginning with 225 KHz air-coupled ultrasonic testing (ACUT) and 5-MHz ultrasonic immersion testing. For all panels ultrasonic through-transmission C-scans reveal interesting patterns of signal amplitude and time-of-flight variations. These are traced to lateral changes in adhesive thickness within the panels. For one panel, adhesive sound speed, attenuation and density are deduced by analyzing UT immersion pulse/echo and pitch/catch data. Adhesive thickness variations manifest themselves differently in the two types of ultrasonic inspections. At the immersion inspection frequency adhesive attenuation dominates, so regions with thicker adhesive always have the smallest through-transmitted response. At ACUT frequencies reverberation echoes within the adhesive layer superimpose with echoes from other sound paths, and an increase in adhesive thickness can result in either an increase or decrease in through-transmitted amplitude. A simple model to account for such signal superposition is developed and found to be in qualitative agreement with the results of the ACUT inspections. The adhesive thickness variations cause the surfaces within the panel to be non-planar, leading to stresses on the various layers. We demonstrate the use of Terahertz-ray (T-ray) electromagnetic inspection to map the surface undulations of the thin glass outer layer in one of the panels. Bending stresses are estimated from the undulations and, at some locations, found to be at or near the levels that would cause fracture.