Vinay Dayal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Vinay Dayal has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Sunil Kishore Chakrapani
Michigan State University
6 shared publications - Richard Livings
Aerospace Engineering, Iowa State University, Ames, USA
5 shared publications - Dan Barnard
Center for Nondestructive Evaluation, Iowa State University, Ames, USA
4 shared publications Daniel Barnard
Center for Nondestructive Evaluation, Iowa State University, 1915 Scholl Road, Ames, IA 50011, USA
4 shared publicationsDaniel J. Barnard
3 shared publicationsAdam G. Harper
1 shared publication
Latest Publications
- 1 May 2026
- Published by Springer Nature
- p. 1-27
Ultrasonic Inspection of Laminated Composites
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1949 (1) , 210001
Micro-crack detection in CFRP laminates using coda wave NDE
Coda Waves or diffuse field has been touted to be an NDE method that does not require the damage to be in the path of the ultrasound. The object is insonified with ultrasound and instead of catching the first or second arrival, the waves are allowed to bounce multiple times. This aspect is very important in structural health monitoring (SHM) where the potential damage development location is unknown. Researchers have used Coda waves in the interrogation of seismic damage and metallic materials. In this work we have applied the technique to composite material, and present the results herein. The coda wave and acoustic emission signals are recorded simultaneously and corroborated. Development of small incipient damage in the form of micro-crack and their detection is the objective of this work.
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1949 (1) , 210001
Micro-crack detection in CFRP laminates using coda wave NDE
Coda Waves or diffuse field has been touted to be an NDE method that does not require the damage to be in the path of the ultrasound. The object is insonified with ultrasound and instead of catching the first or second arrival, the waves are allowed to bounce multiple times. This aspect is very important in structural health monitoring (SHM) where the potential damage development location is unknown. Researchers have used Coda waves in the interrogation of seismic damage and metallic materials. In this work we have applied the technique to composite material, and present the results herein. The coda wave and acoustic emission signals are recorded simultaneously and corroborated. Development of small incipient damage in the form of micro-crack and their detection is the objective of this work.
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1949 (1) , 060006
Development of composite calibration standard for quantitative NDE by ultrasound and thermography
Inspection of aircraft components for damage utilizing ultrasonic Non-Destructive Evaluation (NDE) is a time intensive endeavor. Additional time spent during aircraft inspections translates to added cost to the company performing them, and as such, reducing this expenditure is of great importance. There is also great variance in the calibration samples from one entity to another due to a lack of a common calibration set. By characterizing damage types, we can condense the required calibration sets and reduce the time required to perform calibration while also providing procedures for the fabrication of these standard sets. We present here our effort to fabricate composite samples with known defects and quantify the size and location of defects, such as delaminations, and impact damage. Ultrasonic and Thermographic images are digitally enhanced to accurately measure the damage size. Ultrasonic NDE is compared with thermography.
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1949 (1) , 060006
Development of composite calibration standard for quantitative NDE by ultrasound and thermography
Inspection of aircraft components for damage utilizing ultrasonic Non-Destructive Evaluation (NDE) is a time intensive endeavor. Additional time spent during aircraft inspections translates to added cost to the company performing them, and as such, reducing this expenditure is of great importance. There is also great variance in the calibration samples from one entity to another due to a lack of a common calibration set. By characterizing damage types, we can condense the required calibration sets and reduce the time required to perform calibration while also providing procedures for the fabrication of these standard sets. We present here our effort to fabricate composite samples with known defects and quantify the size and location of defects, such as delaminations, and impact damage. Ultrasonic and Thermographic images are digitally enhanced to accurately measure the damage size. Ultrasonic NDE is compared with thermography.
- 10 February 2017
- Published by Springer Nature in Journal of Nondestructive Evaluation
- Vol. 36 (1) , 1-11
Air-Coupled Ultrasonic Resonance Imaging of Hexagonal SiC and Alumina Tiles
- 10 February 2017
- Published by Springer Nature in Journal of Nondestructive Evaluation
- Vol. 36 (1) , 1-11
Air-Coupled Ultrasonic Resonance Imaging of Hexagonal SiC and Alumina Tiles
- 12 September 2016
- Published by Springer Nature in Journal of Nondestructive Evaluation
- Vol. 35 (4) , 1-9
Damage Detection in a Multi-Layered, Multi-Material Composite Using Air-Coupled Ultrasonic Resonance Imaging
- 12 September 2016
- Published by Springer Nature in Journal of Nondestructive Evaluation
- Vol. 35 (4) , 1-9
Damage Detection in a Multi-Layered, Multi-Material Composite Using Air-Coupled Ultrasonic Resonance Imaging
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1706, 120003
Coda wave interferometry for the measurement of thermally induced ultrasonic velocity variations in CFRP laminates
Ultrasonic velocity measurement is a well-established method to measure properties and estimate strength as well as detect and locate damage. Determination of accurate and repeatable ultrasonic wave velocities can be difficult due to the influence of environmental and experimental factors. Diffuse fields created by a multiple scattering environment have been shown to be sensitive to homogeneous strain fields such as those caused by temperature variations, and Coda Wave Interferometry has been used to measure the thermally induced ultrasonic velocity variation in concrete, aluminum, and the Earth’s crust. In this work, we analyzed the influence of several parameters of the experimental configuration on the measurement of thermally induced ultrasonic velocity variations in a carbon-fiber reinforced polymer plate. Coda Wave Interferometry was used to determine the relative velocity change between a baseline signal taken at room temperature and the signal taken at various temperatures. The influence of several parameters of the experimental configuration, such as the material type, the receiver aperture size, and fiber orientation on the results of the processing algorithm was evaluated in order to determine the optimal experimental configuration.---This work is supported by the NSF Industry/University Cooperative Research Program of the Center for Nondestructive Evaluation at Iowa State University.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1706, 120003
Coda wave interferometry for the measurement of thermally induced ultrasonic velocity variations in CFRP laminates
Ultrasonic velocity measurement is a well-established method to measure properties and estimate strength as well as detect and locate damage. Determination of accurate and repeatable ultrasonic wave velocities can be difficult due to the influence of environmental and experimental factors. Diffuse fields created by a multiple scattering environment have been shown to be sensitive to homogeneous strain fields such as those caused by temperature variations, and Coda Wave Interferometry has been used to measure the thermally induced ultrasonic velocity variation in concrete, aluminum, and the Earth’s crust. In this work, we analyzed the influence of several parameters of the experimental configuration on the measurement of thermally induced ultrasonic velocity variations in a carbon-fiber reinforced polymer plate. Coda Wave Interferometry was used to determine the relative velocity change between a baseline signal taken at room temperature and the signal taken at various temperatures. The influence of several parameters of the experimental configuration, such as the material type, the receiver aperture size, and fiber orientation on the results of the processing algorithm was evaluated in order to determine the optimal experimental configuration.---This work is supported by the NSF Industry/University Cooperative Research Program of the Center for Nondestructive Evaluation at Iowa State University.
- 1 September 2015
- Published by Elsevier in Ultrasonics
- Vol. 62, 126-135
Finite element simulation of core inspection in helicopter rotor blades using guided waves
- 1 September 2015
- Published by Elsevier in Ultrasonics
- Vol. 62, 126-135
Finite element simulation of core inspection in helicopter rotor blades using guided waves
- 1 January 2015
- Published by AIP Publishing in AIP Conference Proceedings
Characterization of 3D rapid prototyped polymeric material by ultrasonic methods
Rapid prototyped parts are quickly becoming a viable alternative for manufacturers. Although the polymeric material is initially isotropic, the printing process introduces a level of anisotropy. This work characterizes the elastic and acoustic properties of the material, after printing, using ultrasonic methods. The elastic constants and the level of anisotropy are determined by measuring the ultrasonic wave velocities. It is shown that the material possesses less symmetry than the orthotropic material model. The dispersion and attenuation characteristics are also determined to provide a basis for ultrasonic flaw detection.
- 1 January 2015
- Published by AIP Publishing in AIP Conference Proceedings
Characterization of 3D rapid prototyped polymeric material by ultrasonic methods
Rapid prototyped parts are quickly becoming a viable alternative for manufacturers. Although the polymeric material is initially isotropic, the printing process introduces a level of anisotropy. This work characterizes the elastic and acoustic properties of the material, after printing, using ultrasonic methods. The elastic constants and the level of anisotropy are determined by measuring the ultrasonic wave velocities. It is shown that the material possesses less symmetry than the orthotropic material model. The dispersion and attenuation characteristics are also determined to provide a basis for ultrasonic flaw detection.
- 1 March 2014
- Published by Elsevier in Ultrasonics
- Vol. 54 (3) , 826-833
Nondestructive evaluation of helicopter rotor blades using guided Lamb modes
- 1 March 2014
- Published by Elsevier in Ultrasonics
- Vol. 54 (3) , 826-833
Nondestructive evaluation of helicopter rotor blades using guided Lamb modes