Tetsuo Oka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tetsuo Oka has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Jun Ogawa
4 shared publications- Satoshi Fukui
Graduate School of Science and Technology, Niigata University, Niigata, Japan
4 shared publications - Takao Sato
Graduate School of Science and Technology, Niigata University, Niigata, Japan
4 shared publications Kazuya Yokoyama
2 shared publicationsNaoto Watanabe
2 shared publicationsEranda Kulawansha
1 shared publication
Latest Publications
- 19 January 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 26 (4) , 1-4
Development of a Desktop-Type Superconducting Bulk Magnet
We developed a desktop-type superconducting bulk magnet using a Stirling cryocooler with the aim of miniaturizing the system. This refrigerator was compact and highly energy efficient because a compressor was not needed outside; power consumption was approximately 160 W. Moreover, the length of the magnetic pole was decreased by restricting the activation method to pulsed field magnetization. A GdBCO bulk material 45 mm in diameter and 20 mm thick was attached to the cold stage of a refrigerator and was covered with a vacuum chamber. The sample was cooled from room temperature to 52.3 K in approximately 4.5 h. When a single pulsed field was applied in amplitudes varying from 0.8 to 7.0 T, the maximum trapped field was approximately 2.8 T at the center of the bulk surface in the applied field of 7.0 T. Moreover, the maximum magnetic field on the chamber's surface was approximately 1.3 T, and the total magnetic flux was 0.94 mWb. The operational status after magnetization was good, and the operating sound was small.
- 19 January 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 26 (4) , 1-4
Development of a Desktop-Type Superconducting Bulk Magnet
We developed a desktop-type superconducting bulk magnet using a Stirling cryocooler with the aim of miniaturizing the system. This refrigerator was compact and highly energy efficient because a compressor was not needed outside; power consumption was approximately 160 W. Moreover, the length of the magnetic pole was decreased by restricting the activation method to pulsed field magnetization. A GdBCO bulk material 45 mm in diameter and 20 mm thick was attached to the cold stage of a refrigerator and was covered with a vacuum chamber. The sample was cooled from room temperature to 52.3 K in approximately 4.5 h. When a single pulsed field was applied in amplitudes varying from 0.8 to 7.0 T, the maximum trapped field was approximately 2.8 T at the center of the bulk surface in the applied field of 7.0 T. Moreover, the maximum magnetic field on the chamber's surface was approximately 1.3 T, and the total magnetic flux was 0.94 mWb. The operational status after magnetization was good, and the operating sound was small.
- 3 November 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 25 (3) , 1-4
A Numerical Proposal of an After Heating Method for Pulse Field Magnetization for HTS Bulk Magnets
Pulse field magnetization (PFM) for HTS bulk magnets has the advantage of a field cooling method, because it does not require a superconducting magnet. To reach the largest trapped magnetic field in the HTS bulk using the PFM method requires repeated applications of the pulse magnetic fields to the HTS bulk with controlled temperature and amplitude of the pulse magnetic field. We previously reported the influence of HTS bulk properties on the PFM method, and our numerical results corresponded with the experimental results when a single pulse magnetic field was applied. In this study, we applied multi pulse magnetic fields to the HTS bulk using this numerical model. The results show the outer and inner shielding currents in the HTS bulk exist in opposite directions, while the surface magnetic field is reduced by the magnetic field produced by the negative direction current. We suggest a new method to reduce the outer shielding current using a heater. Our numerical results demonstrate the possibility of increasing the peak of the trapped magnetic field in the heating method.
- 3 November 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 25 (3) , 1-4
A Numerical Proposal of an After Heating Method for Pulse Field Magnetization for HTS Bulk Magnets
Pulse field magnetization (PFM) for HTS bulk magnets has the advantage of a field cooling method, because it does not require a superconducting magnet. To reach the largest trapped magnetic field in the HTS bulk using the PFM method requires repeated applications of the pulse magnetic fields to the HTS bulk with controlled temperature and amplitude of the pulse magnetic field. We previously reported the influence of HTS bulk properties on the PFM method, and our numerical results corresponded with the experimental results when a single pulse magnetic field was applied. In this study, we applied multi pulse magnetic fields to the HTS bulk using this numerical model. The results show the outer and inner shielding currents in the HTS bulk exist in opposite directions, while the surface magnetic field is reduced by the magnetic field produced by the negative direction current. We suggest a new method to reduce the outer shielding current using a heater. Our numerical results demonstrate the possibility of increasing the peak of the trapped magnetic field in the heating method.
- 16 September 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 24 (3) , 1-4
Numerical Study of the Influence of Material Properties on Pulsed-Field Magnetization for HTS Bulk Magnets
To optimize pulse field magnetization processes for high-temperature superconducting (HTS) bulk magnets, it is important to control the magnetic field amplitude and the driving temperature. Many publications have reported on the experimental and numerical results of the pulsed-field magnetization method. In the numerical method, the HTS bulk properties are modeled to simplify the calculations, examples being the Bean model and the Kim model, etc. During pulsed-field magnetization the critical current density in the HTS bulk changes dramatically due to the magnetic field and temperature rise induced by the ac losses. For these reasons these properties are key to the analysis of the pulsed-field magnetization process, which is calculated using the measured practical HTS bulk properties, and these results show different temperature rise and trapped magnetic field characteristics. We assumed that HTS bulk has intrinsic deterioration in practice. Therefore, we recalculated using the adjusted parameters, and these analytic results correspond with the experimental results.
- 16 September 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 24 (3) , 1-4
Numerical Study of the Influence of Material Properties on Pulsed-Field Magnetization for HTS Bulk Magnets
To optimize pulse field magnetization processes for high-temperature superconducting (HTS) bulk magnets, it is important to control the magnetic field amplitude and the driving temperature. Many publications have reported on the experimental and numerical results of the pulsed-field magnetization method. In the numerical method, the HTS bulk properties are modeled to simplify the calculations, examples being the Bean model and the Kim model, etc. During pulsed-field magnetization the critical current density in the HTS bulk changes dramatically due to the magnetic field and temperature rise induced by the ac losses. For these reasons these properties are key to the analysis of the pulsed-field magnetization process, which is calculated using the measured practical HTS bulk properties, and these results show different temperature rise and trapped magnetic field characteristics. We assumed that HTS bulk has intrinsic deterioration in practice. Therefore, we recalculated using the adjusted parameters, and these analytic results correspond with the experimental results.
- 1 November 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 21 (3) , 2241-2244
Development and Test of Model Apparatus Utilizing HTS Magnetic Levitation for Non-Contact Spinning Clean-Up Processors of Photo Mask Production
It is considered that particle deposition on the photo mask, such as oil dusts which are generated from mechanical bearings of the spin processors, is one of main causes of the deterioration of pattern preciseness. In our R & D, application of magnetic levitation utilizing bulk HTSs to the spin processors for the photo mask production has been proposed. In this study, we try to develop a new model apparatus demonstrating non-contact spinning clean-up processor in photo mask production system. The levitation and rotation test by using this model apparatus showed that this new model apparatus accomplished the remarkable improvement of the levitation and the rotation ability. This paper describes the levitation and rotation test results of the new model spinner comparing with those obtained in our previous study.
- 1 November 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 21 (3) , 2241-2244
Development and Test of Model Apparatus Utilizing HTS Magnetic Levitation for Non-Contact Spinning Clean-Up Processors of Photo Mask Production
It is considered that particle deposition on the photo mask, such as oil dusts which are generated from mechanical bearings of the spin processors, is one of main causes of the deterioration of pattern preciseness. In our R & D, application of magnetic levitation utilizing bulk HTSs to the spin processors for the photo mask production has been proposed. In this study, we try to develop a new model apparatus demonstrating non-contact spinning clean-up processor in photo mask production system. The levitation and rotation test by using this model apparatus showed that this new model apparatus accomplished the remarkable improvement of the levitation and the rotation ability. This paper describes the levitation and rotation test results of the new model spinner comparing with those obtained in our previous study.
- 5 April 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 20 (3) , 2138-2141
Numerical Analysis of Relation Between AC Loss Characteristics and Geometrical Parameters of Multi-Layer Polygonal Conductor Assembled by HTS Coated Conductor
This paper presents numerical studies on influences of geometrical parameters on AC loss in 2-layer cable conductors assembled by YBCO tapes in polygonal arrangement. By using the numerical model developed in our previous works, the AC loss characteristics of the 2- layer polygonal cable assembled by the YBCO tapes are analyzed with changing the cable geometrical parameters such as the tape width and the tape-to-tape gap. The numerical results show the strong influences of these parameters on the AC loss characteristics. Based on the numerical data, the effects of the decrease in the tape width and the tape-to-tape gap on AC loss reduction were evaluated. The numerical results also give the important information for the design of the multi-layer YBCO cable conductor.
- 5 April 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 20 (3) , 2138-2141
Numerical Analysis of Relation Between AC Loss Characteristics and Geometrical Parameters of Multi-Layer Polygonal Conductor Assembled by HTS Coated Conductor
This paper presents numerical studies on influences of geometrical parameters on AC loss in 2-layer cable conductors assembled by YBCO tapes in polygonal arrangement. By using the numerical model developed in our previous works, the AC loss characteristics of the 2- layer polygonal cable assembled by the YBCO tapes are analyzed with changing the cable geometrical parameters such as the tape width and the tape-to-tape gap. The numerical results show the strong influences of these parameters on the AC loss characteristics. Based on the numerical data, the effects of the decrease in the tape width and the tape-to-tape gap on AC loss reduction were evaluated. The numerical results also give the important information for the design of the multi-layer YBCO cable conductor.
- Open Access
- 24 November 2004
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 18 (1) , 158-165
Generated heat during pulse field magnetizing for REBaCuO (RE = Gd, Sm, Y) bulk superconductors with different pinning abilities
- 24 November 2004
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 18 (1) , 158-165
Open AccessGenerated heat during pulse field magnetizing for REBaCuO (RE = Gd, Sm, Y) bulk superconductors with different pinning abilities
- 1 January 2004
- Published by Japan Society of Mechanical Engineers in The Proceedings of Conference of Tokai Branch
- Vol. 2004.53, 57-58
Development of superconducting strong magnetic field generators
総合学術電子ジャーナルサイト「J-STAGE」-国内で発行された学術論文全文を読むことのできる、日本最大級の総合電子ジャーナルプラットフォームです。
- 1 January 2004
- Published by Japan Society of Mechanical Engineers in The Proceedings of Conference of Tokai Branch
- Vol. 2004.53, 57-58
Development of superconducting strong magnetic field generators
総合学術電子ジャーナルサイト「J-STAGE」-国内で発行された学術論文全文を読むことのできる、日本最大級の総合電子ジャーナルプラットフォームです。