Satoshi Fukui
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Satoshi Fukui has a total of 198 co-authors. Here are the top co-authors by number of shared publications:
- Jun Ogawa
Graduate School of Science and Technology, Niigata University, Niigata, Japan
24 shared publications Takao Sato
Niigata Univ, Fac Engn, Nishi Ku, 8050 Ikarashi Ni No Cho, Niigata 8050, Japan
18 shared publicationsTetsuo Oka
Graduate School of Science and Technology, Niigata University, Niigata, Japan
13 shared publicationsJun Ogawa
Niigata Univ, Fac Engn, Nishi Ku, 8050 Ikarashi Ni No Cho, Niigata 8050, Japan
11 shared publicationsMitsugi Yamaguchi
Graduate School of Science and Technology, Niigata University, Niigata, Japan
11 shared publicationsOsami Tsukamoto
Yokohama National University, Kanagawa, Japan
7 shared publications
Latest Publications
- 18 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Study on Aluminum Melting by Superconducting DC Induction Heating
Direct current (DC) induction heating using a superconducting magnet to supply molten aluminum efficiently and in a short time was investigated. In the DC induction heating system, aluminum samples in the sample holder are rotated around a rotation axis orthogonal to the magnetic field. To apply a strong magnetic field to the samples, the conduction-cooled split coil pair consisting of eight rectangular REBCO double pancake (DP) coils with an inductance of about 200 mH each was fabricated and confirmed to generate the designed magnetic field. Observations of molten aluminum samples in previous experiments and analysis using Hartmann numbers indicate that the movement of molten aluminum in the holder reduces the velocity of rotation in a magnetic field. Wrapping the aluminum samples with stainless-steel sheets and fixing them in the sample holder, the molten samples were able to rotate smoothly with the holder in the magnetic field. A melting test was performed by rotating the aluminum sample at 1,115 rpm in a magnetic field of about 900 mT using a split coil pair, and it was confirmed that the aluminum sample could be completely melted. Measurements of the motor input revealed that this is a highly efficient melting method and enables aluminum melting in a short period of time.
- 18 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (3) , 1-5
Study on Aluminum Melting by Superconducting DC Induction Heating
Direct current (DC) induction heating using a superconducting magnet to supply molten aluminum efficiently and in a short time was investigated. In the DC induction heating system, aluminum samples in the sample holder are rotated around a rotation axis orthogonal to the magnetic field. To apply a strong magnetic field to the samples, the conduction-cooled split coil pair consisting of eight rectangular REBCO double pancake (DP) coils with an inductance of about 200 mH each was fabricated and confirmed to generate the designed magnetic field. Observations of molten aluminum samples in previous experiments and analysis using Hartmann numbers indicate that the movement of molten aluminum in the holder reduces the velocity of rotation in a magnetic field. Wrapping the aluminum samples with stainless-steel sheets and fixing them in the sample holder, the molten samples were able to rotate smoothly with the holder in the magnetic field. A melting test was performed by rotating the aluminum sample at 1,115 rpm in a magnetic field of about 900 mT using a split coil pair, and it was confirmed that the aluminum sample could be completely melted. Measurements of the motor input revealed that this is a highly efficient melting method and enables aluminum melting in a short period of time.
- 6 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-4
Numerical Investigation of AC Losses in Toroidal Full-Superconducting Resonator Using ReBCO Tapes
High-temperature superconducting (HTS) tapes exhibit a flat plate structure. Experiments have shown the characteristics of pancake-type superconducting capacitor using HTS tapes as electrodes. This pancake-type HTS capacitor also functions as an inductance because it creates a self-magnetic field, and the inductance and capacitance facilitate the creation of an all-superconducting resonant circuit by itself. As AC loss in the HTS circuit is converted into a resistive component, it exerts a significant impact on the Q-factor characteristic, which is the evaluation standard for resonant circuits. Thus, evaluating AC loss characteristics is very important for designing fully superconducting resonant circuits. In this study, the current distribution is not uniform towing to the charge transfer between electrodes in the toroidal full-superconducting resonator; thus, the AC loss was derived in each part using the finite element method (FEM). FEM was employed to derive the AC loss and Q-factor. Considering the resistance component that exists due to the AC losses being nonlinear with respect to the current, a simple equivalent circuit was used to derive the Q-factor.
- 6 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-4
Numerical Investigation of AC Losses in Toroidal Full-Superconducting Resonator Using ReBCO Tapes
High-temperature superconducting (HTS) tapes exhibit a flat plate structure. Experiments have shown the characteristics of pancake-type superconducting capacitor using HTS tapes as electrodes. This pancake-type HTS capacitor also functions as an inductance because it creates a self-magnetic field, and the inductance and capacitance facilitate the creation of an all-superconducting resonant circuit by itself. As AC loss in the HTS circuit is converted into a resistive component, it exerts a significant impact on the Q-factor characteristic, which is the evaluation standard for resonant circuits. Thus, evaluating AC loss characteristics is very important for designing fully superconducting resonant circuits. In this study, the current distribution is not uniform towing to the charge transfer between electrodes in the toroidal full-superconducting resonator; thus, the AC loss was derived in each part using the finite element method (FEM). FEM was employed to derive the AC loss and Q-factor. Considering the resistance component that exists due to the AC losses being nonlinear with respect to the current, a simple equivalent circuit was used to derive the Q-factor.
- 14 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
AC Loss Measurements of Coils Wound With Spiral-Coated-Conductor Cables
We fabricated a multi-layer coil with multiple turns per layer using a spiral-coated-conductor cable and measured its ac losses. Additionally, we measured the transport & magnetization losses of a short sample of the cable and integrated them to estimate the losses in the entire coil. The measured ac loss of the coil was significantly larger than the integrated transport loss of the short sample, likely because the ac loss in a turn of the coil was dominated by the transverse magnetic field generated by other turns. Furthermore, the measured coil loss was larger than the sum of the integrated transport and magnetization losses. The interaction between the transverse magnetic field and the azimuthal self-magnetic field of each turn might cause this difference.
- 14 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
AC Loss Measurements of Coils Wound With Spiral-Coated-Conductor Cables
We fabricated a multi-layer coil with multiple turns per layer using a spiral-coated-conductor cable and measured its ac losses. Additionally, we measured the transport & magnetization losses of a short sample of the cable and integrated them to estimate the losses in the entire coil. The measured ac loss of the coil was significantly larger than the integrated transport loss of the short sample, likely because the ac loss in a turn of the coil was dominated by the transverse magnetic field generated by other turns. Furthermore, the measured coil loss was larger than the sum of the integrated transport and magnetization losses. The interaction between the transverse magnetic field and the azimuthal self-magnetic field of each turn might cause this difference.
- 1 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-4
Test of High Temperature Superconducting REBCO Coil Assembly for a Multi-Frequency ECR Ion Source
High temperature superconducting REBCO tape has the characteristic of maintaining high critical current density under strong external magnetic field, which makes it an ideal material for the construction of air-core electromagnets of accelerator and electron cyclotron resonance (ECR) ion source. In Research Center for Nuclear Physics, Osaka University, a non-insulated air-cored REBCO coil assembly has been constructed. This coil assebmly consists of three circular REBCO solenoid and six racetrack REBCO coil. This coil assembly will be used as an electromagnet of a multi-frequency ECR ion source, and is also developed as a key technology development of an air-core cyclotron. The magnetic field of this ion source are designed, and 77 K performance tests of the assembly are carried out in order to examine the capability of REBCO coils of inducing magnetic field under external field. In this work, the test results and the magnetic field designed for the ECR ion source will be presented and discussed.
- 1 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-4
Test of High Temperature Superconducting REBCO Coil Assembly for a Multi-Frequency ECR Ion Source
High temperature superconducting REBCO tape has the characteristic of maintaining high critical current density under strong external magnetic field, which makes it an ideal material for the construction of air-core electromagnets of accelerator and electron cyclotron resonance (ECR) ion source. In Research Center for Nuclear Physics, Osaka University, a non-insulated air-cored REBCO coil assembly has been constructed. This coil assebmly consists of three circular REBCO solenoid and six racetrack REBCO coil. This coil assembly will be used as an electromagnet of a multi-frequency ECR ion source, and is also developed as a key technology development of an air-core cyclotron. The magnetic field of this ion source are designed, and 77 K performance tests of the assembly are carried out in order to examine the capability of REBCO coils of inducing magnetic field under external field. In this work, the test results and the magnetic field designed for the ECR ion source will be presented and discussed.
- 10 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-4
Noncontact Evaluation of HTS Cylinder for Compact Cryogen-Free NMR
Herein, a compact cryogen-free nuclear magnetic resonance (NMR) system is developed using a stacked high-temperature superconducting (HTS) bulk system. To compensate for magnetic field uniformity, an HTS cylinder is installed inside the measurement space. The cylinder is wound with REBCO tapes placed on the surface of a copper cylinder. The uniformity of its critical current density is important for NMR signal detection. Such an operation requires an examination of the quality of the critical-current-density distribution of the cylinder. A noncontact measurement method is required for such an examination. When a magnetic field is applied, the superconductor exhibits a demagnetization effect. Moreover, if any defect exists in any part of the superconducting tape, that particular part would contain no demagnetization, thus disturbing the relevant magnetic field distribution. In this study, this phenomenon is investigated using DC and AC magnetic fields. The magnets and sensor are placed inside the HTS cylinder, and magnetic fields are applied to the HTS cylinder surface. The results confirm that the proposed method is effective and applicable for evaluating the critical-current distribution.
- 10 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-4
Noncontact Evaluation of HTS Cylinder for Compact Cryogen-Free NMR
Herein, a compact cryogen-free nuclear magnetic resonance (NMR) system is developed using a stacked high-temperature superconducting (HTS) bulk system. To compensate for magnetic field uniformity, an HTS cylinder is installed inside the measurement space. The cylinder is wound with REBCO tapes placed on the surface of a copper cylinder. The uniformity of its critical current density is important for NMR signal detection. Such an operation requires an examination of the quality of the critical-current-density distribution of the cylinder. A noncontact measurement method is required for such an examination. When a magnetic field is applied, the superconductor exhibits a demagnetization effect. Moreover, if any defect exists in any part of the superconducting tape, that particular part would contain no demagnetization, thus disturbing the relevant magnetic field distribution. In this study, this phenomenon is investigated using DC and AC magnetic fields. The magnets and sensor are placed inside the HTS cylinder, and magnetic fields are applied to the HTS cylinder surface. The results confirm that the proposed method is effective and applicable for evaluating the critical-current distribution.
- 9 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-4
AC Loss Estimation Model for High-Temperature Superconducting Cables Derived From Experiments Simulating Electromagnetic Environments
In a previous study, the AC loss characteristics of each layer of a high-temperature superconducting (HTS) AC cable were experimentally investigated (Ogawa et al., 2020; Ogawa et al., 2017; Ogawa et al., 2019). Based on these data, we modeled the AC loss in a superconducting cable by considering the maxi-mum and minimum values of the loss. A comparison between this model and the experimental data showed good agreement. Hence, it is possible to estimate AC loss under electromagnetic conditions in a high-temperature superconducting cable. This model makes it possible to determine the losses of each layer in the superconducting cable and to design the minimum AC loss load of the superconducting cable. This model estimates the AC losses of a three-layer twisted HTS cable.
- 9 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-4
AC Loss Estimation Model for High-Temperature Superconducting Cables Derived From Experiments Simulating Electromagnetic Environments
In a previous study, the AC loss characteristics of each layer of a high-temperature superconducting (HTS) AC cable were experimentally investigated (Ogawa et al., 2020; Ogawa et al., 2017; Ogawa et al., 2019). Based on these data, we modeled the AC loss in a superconducting cable by considering the maxi-mum and minimum values of the loss. A comparison between this model and the experimental data showed good agreement. Hence, it is possible to estimate AC loss under electromagnetic conditions in a high-temperature superconducting cable. This model makes it possible to determine the losses of each layer in the superconducting cable and to design the minimum AC loss load of the superconducting cable. This model estimates the AC losses of a three-layer twisted HTS cable.
- 1 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
Development of 400 kW Class Aluminum Billet Heater Using HTS Magnet
In this paper, design, fabrication, and test results of the demonstration device for 400 kW-class aluminum billet heating using the HTS magnet were reported. Based on our user's request, the target of the demonstration device was to heat the aluminum billet of 155 mm in diameter and 500 mm in length from room temperature to 500 ℃ within 60 seconds. In the heating test using the demonstration device, it was demonstrated that the input heating power to the aluminum billet of 155 mm in diameter and 500 mm long was more than 400 kW. Based on the measured data of the heating tests, the heating efficiency was estimated to be 74.5%. It was shown that at least 30% reduction of energy consumption could be possible compared to conventional induction heating devices.
- 1 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
Development of 400 kW Class Aluminum Billet Heater Using HTS Magnet
In this paper, design, fabrication, and test results of the demonstration device for 400 kW-class aluminum billet heating using the HTS magnet were reported. Based on our user's request, the target of the demonstration device was to heat the aluminum billet of 155 mm in diameter and 500 mm in length from room temperature to 500 ℃ within 60 seconds. In the heating test using the demonstration device, it was demonstrated that the input heating power to the aluminum billet of 155 mm in diameter and 500 mm long was more than 400 kW. Based on the measured data of the heating tests, the heating efficiency was estimated to be 74.5%. It was shown that at least 30% reduction of energy consumption could be possible compared to conventional induction heating devices.
- 20 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (4) , 1-5
Fabrication and Test of HTS Magnet for Induction Heating Device in Aluminum Extrusion Processing
This paper reported the fabrication and the test results of the high temperature superconducting (HTS) magnet developed for the aluminum billet heater for aluminum extrusion processing. In this magnet, the HTS coils were combined with iron cores, because the required magnetic field in the working region was about 1T. Two HTS coils wound directly on the convex shape iron cores were fabricated. The HTS coils were made by the no-insulation winding of REBCO tape with the YOROI-coil technique. Each of them was separately installed in an individual cryostat. Two HTS coils with iron cores were disposed oppositely to each other and were magnetically connected by a C-shape yoke placed in room temperature. The HTS coil was cooled down to about 15 K by the GM cryocooler in the initial cooling. The magnetic field of 1.06 T at the center of the heating region was stably generated with the rated current of 200 A. It was also demonstrated that the HTS magnet could be charged up to 300 A without quench. According to the observation of the electromagnetic force direction from the outside of the cryostat, it was confirmed the validity of the force balance design of the magnet.
- 20 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (4) , 1-5
Fabrication and Test of HTS Magnet for Induction Heating Device in Aluminum Extrusion Processing
This paper reported the fabrication and the test results of the high temperature superconducting (HTS) magnet developed for the aluminum billet heater for aluminum extrusion processing. In this magnet, the HTS coils were combined with iron cores, because the required magnetic field in the working region was about 1T. Two HTS coils wound directly on the convex shape iron cores were fabricated. The HTS coils were made by the no-insulation winding of REBCO tape with the YOROI-coil technique. Each of them was separately installed in an individual cryostat. Two HTS coils with iron cores were disposed oppositely to each other and were magnetically connected by a C-shape yoke placed in room temperature. The HTS coil was cooled down to about 15 K by the GM cryocooler in the initial cooling. The magnetic field of 1.06 T at the center of the heating region was stably generated with the rated current of 200 A. It was also demonstrated that the HTS magnet could be charged up to 300 A without quench. According to the observation of the electromagnetic force direction from the outside of the cryostat, it was confirmed the validity of the force balance design of the magnet.
- 20 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-4
Magnetizing Technique for Permanent Magnets in IPM Motor Rotors Using HTS Bulk Magnet
A unique activation technique for permanent Nd-Fe-B magnets which were embedded in the rotors of interior permanent magnet (IPM) motors has been developed as a magnetizing tool with use of high temperature superconducting (HTS) bulk magnet. The experimental and numerical simulation studies were conducted to evaluate the magnetic field-trapping performances of the rotor of air-conditioner compressor in the hybrid-type automobiles. The sample rotor containing six demagnetized permanent magnet plates were exposed in the intense static magnetic fields above the magnetic pole which contained the bulk magnet generating over 4 T. As a result, the sample magnets were perfectly magnetized in the static magnetic field. The precise simulation on the flux distribution in the rotor clarified that it is important to make the flux direction in the rotor core and the easy magnetization axis of PM identical. We convinced this activation technique should enable us to promote the degrees of freedom of motor designing and its processing.
- 20 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-4
Magnetizing Technique for Permanent Magnets in IPM Motor Rotors Using HTS Bulk Magnet
A unique activation technique for permanent Nd-Fe-B magnets which were embedded in the rotors of interior permanent magnet (IPM) motors has been developed as a magnetizing tool with use of high temperature superconducting (HTS) bulk magnet. The experimental and numerical simulation studies were conducted to evaluate the magnetic field-trapping performances of the rotor of air-conditioner compressor in the hybrid-type automobiles. The sample rotor containing six demagnetized permanent magnet plates were exposed in the intense static magnetic fields above the magnetic pole which contained the bulk magnet generating over 4 T. As a result, the sample magnets were perfectly magnetized in the static magnetic field. The precise simulation on the flux distribution in the rotor clarified that it is important to make the flux direction in the rotor core and the easy magnetization axis of PM identical. We convinced this activation technique should enable us to promote the degrees of freedom of motor designing and its processing.
- 13 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-5
Experimental Investigation of AC Loss Characteristics under HTS Cable Electromagnetic Conditions
- 13 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-5
Experimental Investigation of AC Loss Characteristics under HTS Cable Electromagnetic Conditions