Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Wojciech Pawlak has a total of 68 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Wear Behavior of Al2O3/Ti3AlC2-MAX Composites at Elevated Temperatures

    by Jaroslaw Wozniak, Wojciech Pawlak, Kamil Broniszewski, Tomasz Cygan, Anna Jędrzejczak, Andrzej Olszyna, Bartłomiej Przybyszewski

    This paper investigates the effect of Ti3AlC2-MAX phase addition as a solid lubricant to Al2O3. The composites were prepared using powder metallurgy and consolidated by Spark Plasma Sintering (SPS). The influence of Ti3AlC2 addition on phase composition and mechanical and tribological properties was evaluated. The use of MAX phase allows for the fabrication of sintered materials characterized by high density, a hardness close to 2000 HV5, and a fracture toughness of 5.5 MPa*m0.5 for the sample containing 10 wt.% Ti3AlC2. Moreover, a significant reduction in wear of the composites was observed for friction tests conducted at 700 °C compared to the unreinforced sample. The research demonstrates that Ti3AlC2 can serve as a solid lubricant and exhibits the best performance at high temperatures.


  • Open Access

    Formation and Mechano-Chemical Properties of Chromium Fluorides Originated from the Deposition of Carbon-Chromium Nanocomposite Coatings in the Reactive Atmosphere (Ar + CF4) during Magnetron Sputtering

    by Adam Roślak, Józef Doering, Wioletta Strzałka, Marcin Makówka, Anna Jędrzejczak, Łukasz Kołodziejczyk, Jacek Balcerzak, Łukasz Jóźwiak, Ireneusz Piwoński, Wojciech Pawlak

    The literature analysis did not indicate any studies on fluorination tests of carbon nanocomposite coatings doped with transition metals in a form of nanocrystalline metal carbide in amorphous carbon matrix (nc-MeC/a-C). As a model coating to investigate the effect of fluorination in a tetrafluoromethane (CF4) atmosphere, a nanocomposite carbon coating doped with chromium-forming nanocrystals of chromium carbides in a-C matrix (nc-CrC/a-C) produced by magnetron sputtering from graphite targets and using a Pulse-DC type medium frequency power supply was chosen. After the deposition of the gradient chromium carbonitride (CrCN) adhesive sublayer, the fluorination of the main coating was conducted in a reactive mode in an (Ar + CF4) atmosphere at various CF4 content. It was observed that the presence of CF4 in the atmosphere resulted in a reduced amount of chromium carbides formed in favor of chromium fluorides. Thus far, this is an observation that seems unnoticed by the carbon coatings researchers. Fluorine was assumed to bond much more readily to carbon than to chromium, due to the stability of tetrafluoromethane (CF4). The opposite seems to be true. The mechanical properties (nano-hardness and Young’s modulus) and tribological properties in the ‘pin-on-disc’ friction pair are presented, along with the analysis of bonds occurring between chromium, carbon, and fluorine by means of X-ray photoelectron spectroscopy (XPS).

  • Open Access

    Formation and Mechano-Chemical Properties of Chromium Fluorides Originated from the Deposition of Carbon-Chromium Nanocomposite Coatings in the Reactive Atmosphere (Ar+CF4) during Magnetron Sputtering

    by Adam Roślak, Józef Doering, Wioletta Strzałka, Marcin Makówka, Anna Jędrzejczak, Łukasz Kołodziejczyk, Jacek Balcerzak, Łukasz Jóźwiak, Ireneusz Piwoński, Wojciech Pawlak

    The literature analysis did not indicate any studies on fluorination tests of carbon nanocomposite coatings doped with transition metals of the nc-MeC/a-C type. This was the motivation for undertaking research in this area. As a model coating to investigate the effect of fluorination in a tetrafluoromethane (CF4) atmosphere, a nano-composite carbon coating doped with chromium nc-CrC/a-C produced by magnetron sputtering from graphite targets and the use of a Pulse-DC type medium frequency power supply was chosen [6]. After deposition of the gradient CrCN adhesive sublayer, fluorination of the main coating was conducted in a reactive mode in an (Ar+CF4) atmosphere at various CF4 contents. It was observed that the presence of CF4 in the atmosphere resulted in a reduced amount of chromium carbides formed in favor of chromium fluorides. So far, this is an observation that seems unnoticed by the carbon coatings researchers. Fluorine was assumed to bond much more readily to carbon than to chromium, due to the stability of tetrafluoromethane (CF4). The opposite seems to be true. The mechanical properties (nano-hardness and Young's modulus) and tribological properties in the 'pin-on-disc' friction pair are presented, along with the analysis of bonds occurring between chromium, carbon, and fluorine (XPS).

  • Open Access

    Research on the Planar Electrical Anisotropy of Conductive Woven Fabrics

    by Magdalena Tokarska, Pamela Miśkiewicz, Wojciech Pawlak

    The main aim of the research is to determine electrical anisotropy of woven fabrics to describe the multidirectional dependence of the electrical resistance of woven fabrics. The van der Pauw electrodes configuration is used to determine the electrical resistance. Scanning electron microscope–energy‐dispersion X‐ray spectroscopy (SEM–EDS) analysis is carried out to identify the real amount of conductive elements on a fabric surface as a result of yarns or fabric metallization and to explain the electrical conductivity of the textile materials. The planar electrical anisotropy of electroconductive woven fabrics is observed. The maximum and minimum values of resistances of woven fabric are connected with the weft/warp of which direction coincides with the direction of the longitudinal and transversal axes in the sample plane. SEM–EDS analysis confirms that the electrical conductivity of fabrics depends on the samples elemental composition and the amount of metals deposited on yarns or woven fabrics. It is observed that the sample metallization with thick coating gives a better solution than weaving textiles from coated yarns from the point of view of electrical properties.


  • Open Access

    Novel Alumina Matrix Composites Reinforced with MAX Phases—Microstructure Analysis and Mechanical Properties

    by Mateusz Petrus, Jaroslaw Wozniak, Tomasz Cygan, Wojciech Pawlak, Andrzej Olszyna

    This article describes the manufacturing of alumina composites with the addition of titanium aluminum carbide Ti3AlC2, known as MAX phases. The composites were obtained by the powder metallurgy technique with three types of mill (horizontal mill, attritor mill, and planetary mill), and were consolidated with the use of the Spark Plasma Sintering method at 1400 °C, with dwelling time 10 min. The influence of the Ti3AlC2 MAX phase addition on the microstructure and mechanical properties of the obtained composites was analyzed. The structure of the MAX phase after the sintering process was also investigated. The chemical composition and phase composition analysis showed that the Ti3AlC2 addition preserved its structure after the sintering process. The increase in fracture toughness for all series of composites has been noted (over 20% compared to reference samples). Detailed stereological analysis of the obtained microstructures also could determine the influence of the applied mill on the homogeneity of the final microstructure and the properties of obtained composites.


  • Open Access

    Microstructure, Micro-Mechanical and Tribocorrosion Behavior of Oxygen Hardened Ti–13Nb–13Zr Alloy

    by Alicja Łukaszczyk, Sławomir Zimowski, Wojciech Pawlak, Beata Dubiel, Tomasz Moskalewicz

    In the present work, an oxygen hardening of near-β phase Ti–13Nb–13Zr alloy in plasma glow discharge at 700–1000 °C was studied. The influence of the surface treatment on the alloy microstructure, tribological and micromechanical properties, and corrosion resistance is presented. A strong influence of the treatment on the hardened zone thickness, refinement of the α’ laths and grain size of the bulk alloy were found. The outer hardened zone contained mainly an oxygen-rich Ti α’ (O) solid solution. The microhardness and elastic modulus of the hardened zone decreased with increasing hardening temperature. The hardened zone thickness, size of the α’ laths, and grain size of the bulk alloy increased with increasing treatment temperature. The wear resistance of the alloy oxygen-hardened at 1000 °C was about two hundred times, and at 700 °C, even five hundred times greater than that of the base alloy. Oxygen hardening also slightly improved the corrosion resistance. Tribocorrosion tests revealed that the alloy hardened at 700 °C was wear-resistant in a corrosive environment, and when the friction process was completed, the passive film was quickly restored. The results show that glow discharge plasma oxidation is a simple and effective method to enhance the micromechanical and tribological performance of the Ti–13Nb–13Zr alloy.


  • Open Access

    Microstructure and Mechanical Properties of Alumina Composites with Addition of Structurally Modified 2D Ti3C2 (MXene) Phase

    by Tomasz Cygan, Jaroslaw Wozniak, Mateusz Petrus, Artur Lachowski, Wojciech Pawlak, Bogusława Adamczyk-Cieślak, Agnieszka Jastrzębska, Anita Rozmysłowska-Wojciechowska, Tomasz Wojciechowski, Wanda Ziemkowska, et al.

    This study presents new findings related to the incorporation of MXene phases into ceramic. Aluminium oxide and synthesised Ti3C2 were utilised as starting materials. Knowing the tendency of MXenes to oxidation and degradation, particularly at higher temperatures, structural modifications were proposed. They consisted of creating the metallic layer on the Ti3C2, by sputtering the titanium or molybdenum. To prepare the composites, powder metallurgy and spark plasma sintering (SPS) techniques were adopted. In order to evaluate the effectiveness of the applied modifications, the emphasis of the research was placed on microstructural analysis. In addition, the mechanical properties of the obtained sinters were examined. Observations revealed significant changes in the MXenes degradation process, from porous areas with TiC particles (for unmodified Ti3C2), to in situ creation of graphitic carbon (in the case of Ti3C2-Ti/Mo). Moreover, the fracture changed from purely intergranular to cracking with high participation of transgranular mode, analogously. In addition, the results obtained showed an improvement in the mechanical properties for composites with Ti/Mo modifications (an increase of 10% and 15% in hardness and fracture toughness respectively, for specimens with 0.5 wt.% Ti3C2-Mo). For unmodified Ti3C2, enormously cracked areas with spatters emerged during tests, making the measurements impossible to perform.


  • Open Access

    Study on Some Thermal and Electrical Properties of Basalt Fabric Modified with Metal and Ceramics as a Result of Magnetron Sputtering

    by Pamela Miśkiewicz, Iwona Frydrych, Magdalena Tokarska, Wojciech Pawlak

    The main aim of the research was to compare the values of some thermal and electrical parameters obtained for a basalt fabric modified with the metal and ceramics coatings. The surface modification of basalt fabric was made by using a magnetron sputtering technique. Chrome and zirconium(IV) oxide coatings were deposited on the fabric surface. The thermal and electrical properties of selected fabrics were determined. In order to assess the comfort properties of fabrics, the thermal resistance of materials was analyzed. Instrumental color measurement was used for an assessment of the surface of modified and unmodified basalt fabric. Using a non-contact digital color imaging system, DigiEye, an original method of samples surface analysis was presented. As a result of research, the modification of basalt fabric surface for applications in a hot work environment enabled the improvement of thermal properties in relation to the references samples. The first level of protection against contact heat for a contact temperature of 100 °C was obtained for the zirconium(IV) oxide-modified basalt fabric. The first level of protection against radiant heat was obtained for all samples. The highest value for the heat radiant resistance was obtained for the chrome-modified basalt fabric.


  • Open Access

    Modification of Surface of Basalt Fabric on Protecting Against High Temperatures by the Method of Magnetron Sputtering

    by Pamela Miśkiewicz, Iwona Frydrych, Wojciech Pawlak, Agnieszka Cichocka

    Basalt fibers and fabrics made of these are characterized by excellent thermal and mechanical properties. Therefore, basalt fabrics, due to a good resistance to high temperatures, are frequently applied in the personal protection equipment (PPE). In order to improve their thermal properties and, above all, the contact heat resistance, the process of physical vapor deposition was proposed. The process of Physical Vapor Deposition (PVD) involves producing a coating on a specific substrate as a result of physical deposition of molecules, ions or atoms of the selected chemical compounds. The method selected for the test is the magnetron sputtering. It involves depositing a uniform film of chromium on the surface of the basalt fabric. In order to improve the thermal properties – especially the contact heat resistance, two values of thickness of the chromium layer deposited on the basalt fabric surface were adopted for the test. Covering 1 μm and 5 μm with the chromium layer did not fulfil the expectations and the research will be continued.