Djoko Setyanto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Djoko Setyanto has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Abdul Mutalib Leman
Universiti Tun Hussein Onn Malaysia
2 shared publications - Adyla Illyana Roseli
Faculty of Engineering Technology, Universiti Tun Hussein Onn Malaysia, Pagoh Higher Education Hub, 84600 Pagoh, Muar, Johor, Malaysia
2 shared publications - Methawee Nukunudompanich
Department of Industrial Engineering, School of Engineering, King Mongkut's Institute of Technology Ladkrabang (KMITL), Bangkok, Thailand
2 shared publications - Najibah Abdul Latif
Mechanical Engineering Studies, College of Engineering, Universiti Teknologi MARA Johor Branch, Pasir Gudang Campus, Jalan Purnama, 81750 Masai, Johor, Malaysia
2 shared publications - Nik Normunira Mat Hassan
Sustainable Polymer Engineering, Advanced Manufacturing and Materials Center (SPEN-AMMC), Faculty of Mechanical and Manufacturing, Engineering Universiti Tun Hussein Onn Malaysia, 86400 Parit Raja, Batu Pahat, Johor, Malaysia
2 shared publications - Ubaidillah Ubaidillah
Universitas Sebelas Maret
2 shared publications
Latest Publications
- 2 November 2026
- Published by Atma Jaya Catholic University of Indonesia in Jurnal Praktik Keinsinyuran
- Vol. 3  (06) , 704-715
Rekonstruksi Mekanisme Kegagalan GTM-CNG Tipe 1 ISO 11439 Berdasarkan Bukti Visual dan Data KNKT: Studi Kasus Kecelakaan Sukabumi 2023
Gas Transportation Module (GTM) based on Compressed Natural Gas (CNG) is a high-pressure transportation system requiring high reliability and safety. The Type 1 CNG GTM accident in Sukabumi in 2023 involved cylinders designed to comply with ISO 11439:2013. This study analyzes the failure mechanism using photographic evidence and KNKT investigation data. Fault Tree Analysis (FTA) and Root Cause Analysis (RCA) are used to evaluate three hypotheses: valve-first, frame-first, and corrosion-first. Results show that KNKT data strongly indicate internal pitting corrosion and external general/uniform attack due to acidic water vapor (pH 4–5) with high water content (74–335 lb/mmscf) as the initiating failure. Corrosion potentially reduces cylinder wall integrity, but no quantitative wall-thickness reduction or visual rupture was found. KNKT stated the cylinder leaked before fracture. Valve and frame damage are significant findings in the failure chain, but the sequence of events cannot be definitively determined. This study emphasizes a system-level integrity approach and the need for destructive testing.
- 2 November 2026
- Published by Atma Jaya Catholic University of Indonesia in Jurnal Praktik Keinsinyuran
- Vol. 3  (06) , 704-715
Rekonstruksi Mekanisme Kegagalan GTM-CNG Tipe 1 ISO 11439 Berdasarkan Bukti Visual dan Data KNKT: Studi Kasus Kecelakaan Sukabumi 2023
Gas Transportation Module (GTM) based on Compressed Natural Gas (CNG) is a high-pressure transportation system requiring high reliability and safety. The Type 1 CNG GTM accident in Sukabumi in 2023 involved cylinders designed to comply with ISO 11439:2013. This study analyzes the failure mechanism using photographic evidence and KNKT investigation data. Fault Tree Analysis (FTA) and Root Cause Analysis (RCA) are used to evaluate three hypotheses: valve-first, frame-first, and corrosion-first. Results show that KNKT data strongly indicate internal pitting corrosion and external general/uniform attack due to acidic water vapor (pH 4–5) with high water content (74–335 lb/mmscf) as the initiating failure. Corrosion potentially reduces cylinder wall integrity, but no quantitative wall-thickness reduction or visual rupture was found. KNKT stated the cylinder leaked before fracture. Valve and frame damage are significant findings in the failure chain, but the sequence of events cannot be definitively determined. This study emphasizes a system-level integrity approach and the need for destructive testing.
- Open Access
- 31 July 2026
- Published by Universitas Airlangga in AKSONA
- Vol. 6  (2) , 105-111
Analysis of Vowel Formants and Frequencies for Cognitive Health Assessment
Highlight: Voice parameters did not differ between cognitive impairment groups Combined speech analysis may better assess cognition than voice alone. ABSTRACT Introduction: Recent studies have shown that, in addition to being cost-effective and non-invasive, voice and speech analysis may play an important role in detecting cognitive impairment, such as dementia. Although numerous studies have investigated this topic, the relationship between voice-related abnormalities and cognitive impairment has not been completely captured. Objective: To investigate the relationship between voice-related abnormalities and cognitive impairment. Methods: A total of 100 participants aged >60 years were selected through purposive sampling. Cognitive function was assessed using the Indonesian version of the Montreal Cognitive Assessment (MoCA-INA), and participants were divided into cognitive impairment and non-cognitive-impairment groups. Acoustic analysis of sustained vowels was conducted using audio analysis software, focusing on formant frequencies, formant centralization ratio, fundamental frequency, and amplitude. Data were analyzed using an independent-samples t-test. Results: The cognitive impairment group demonstrated lower mean values for most formant frequencies. However, no statistically significant differences (p > 0.05) were observed between the groups in formant frequencies, formant centralization ratio, fundamental frequency, or amplitude. Conclusion: No significant association was found between voice-related abnormalities and cognitive impairment. However, subtle variations in voice parameters may still indicate other underlying neurological problems.
- 31 July 2026
- Published by Universitas Airlangga in AKSONA
- Vol. 6  (2) , 105-111
Open AccessAnalysis of Vowel Formants and Frequencies for Cognitive Health Assessment
Highlight: Voice parameters did not differ between cognitive impairment groups Combined speech analysis may better assess cognition than voice alone. ABSTRACT Introduction: Recent studies have shown that, in addition to being cost-effective and non-invasive, voice and speech analysis may play an important role in detecting cognitive impairment, such as dementia. Although numerous studies have investigated this topic, the relationship between voice-related abnormalities and cognitive impairment has not been completely captured. Objective: To investigate the relationship between voice-related abnormalities and cognitive impairment. Methods: A total of 100 participants aged >60 years were selected through purposive sampling. Cognitive function was assessed using the Indonesian version of the Montreal Cognitive Assessment (MoCA-INA), and participants were divided into cognitive impairment and non-cognitive-impairment groups. Acoustic analysis of sustained vowels was conducted using audio analysis software, focusing on formant frequencies, formant centralization ratio, fundamental frequency, and amplitude. Data were analyzed using an independent-samples t-test. Results: The cognitive impairment group demonstrated lower mean values for most formant frequencies. However, no statistically significant differences (p > 0.05) were observed between the groups in formant frequencies, formant centralization ratio, fundamental frequency, or amplitude. Conclusion: No significant association was found between voice-related abnormalities and cognitive impairment. However, subtle variations in voice parameters may still indicate other underlying neurological problems.
- Open Access
- 30 November 2024
- Published by State University of Malang (UM) in Journal of Mechanical Engineering Science and Technology (JMEST)
- Vol. 8  (2) , 363-383
The Potential of Ramie Fiber as Reinforcement in Calcium Carbonate-Filled Polyester Resin Matrix Composites for Roofing Applications
Polymer matrix composite roofing materials available in the Indonesian market typically consist of 30%wt chopped strand mat glass fiber embedded in unsaturated polyester resin, filled with 30 parts per hundred resin (PHR) calcium carbonate. The aim of this research is to evaluate whether natural ramie fibers can potentially replace glass fibers. In the first stage of the study, we compared three types of natural fibers abundant in Indonesia: banana stem fibers, sugarcane bagasse, and ramie. Showed that ramie fiber performed the best. Its flexural strength, flexural modulus, and impact toughness were the highest, measured at 191.57 MPa, 6691 MPa, and 0.056 J/mm², respectively. In the second stage, we produced composite material specimens with the same composition as commercial roofing materials but replaced the glass fibers with ramie fibers. Compared to the material without ramie fibers, the composite reinforced with ramie fibers shows an increase in tensile strength to 47.53 MPa from 34.62 MPa, an increase in maximum water absorption over 14 days to 3.746% from 1.145%, and an improvement in the sound transmission class to 26 dB from 23 dB. Additionally, the ramie fibers did not significantly affect the density of the composite material. However, the inclusion of ramie fibers resulted in a reduction of the elastic modulus to 1324 MPa from 1630 MPa, and a higher mass loss in the TGA examination, at 86.95% compared to 74.65%. Ramie fiber composites achieve the minimum roofing requirement of 40 MPa tensile strength, thus having the potential to replace glass fibers.
- 30 November 2024
- Published by State University of Malang (UM) in Journal of Mechanical Engineering Science and Technology (JMEST)
- Vol. 8  (2) , 363-383
Open AccessThe Potential of Ramie Fiber as Reinforcement in Calcium Carbonate-Filled Polyester Resin Matrix Composites for Roofing Applications
Polymer matrix composite roofing materials available in the Indonesian market typically consist of 30%wt chopped strand mat glass fiber embedded in unsaturated polyester resin, filled with 30 parts per hundred resin (PHR) calcium carbonate. The aim of this research is to evaluate whether natural ramie fibers can potentially replace glass fibers. In the first stage of the study, we compared three types of natural fibers abundant in Indonesia: banana stem fibers, sugarcane bagasse, and ramie. Showed that ramie fiber performed the best. Its flexural strength, flexural modulus, and impact toughness were the highest, measured at 191.57 MPa, 6691 MPa, and 0.056 J/mm², respectively. In the second stage, we produced composite material specimens with the same composition as commercial roofing materials but replaced the glass fibers with ramie fibers. Compared to the material without ramie fibers, the composite reinforced with ramie fibers shows an increase in tensile strength to 47.53 MPa from 34.62 MPa, an increase in maximum water absorption over 14 days to 3.746% from 1.145%, and an improvement in the sound transmission class to 26 dB from 23 dB. Additionally, the ramie fibers did not significantly affect the density of the composite material. However, the inclusion of ramie fibers resulted in a reduction of the elastic modulus to 1324 MPa from 1630 MPa, and a higher mass loss in the TGA examination, at 86.95% compared to 74.65%. Ramie fiber composites achieve the minimum roofing requirement of 40 MPa tensile strength, thus having the potential to replace glass fibers.
- Open Access
- 2 June 2024
- Published by Akademia Baru Publishing in Journal of Advanced Research in Applied Mechanics
- Vol. 117  (1) , 91-106
Morphological, TGA, and FTIR on Rigid Polyurethane Composite Laminated with Untreated and Treated Bamboo Fiber Roof Insulation
The performance of roof insulation such as polyurethane decreased due to problems such as insufficient absorption and poor thermal insulation performance, especially during rainstorms. The aims of this study are to investigate the physical property and its potential reinforced material such as rigid polyurethane doped with treated and untreated bamboo fiber composite (RPU-BF) at different ratios of 0, 25, 30, 35, and 40% of bamboo fibers as an insulation material for roof applications. The bamboo fibers were treated by using silane coupling agent treatment. The rigid polyurethane composite samples were prepared and then laminated bamboo fiber to overcome the sound problem in roofs. The physical characterization was investigated by Water Contact Angle (WCA), the morphological by Scanning Electron Microscopy (SEM), Thermo-gravimetric Analysis (TGA), and Fourier Transform Infrared Spectroscopy (FTIR) Analysis. The results showed that the treated bamboo fiber had a 192.5° water contact angle as a super hydrophobic property due to the presence of the chemical bonds Si-O-Si and Si-O-C in the silane coupling agent treatment. The morphology showed that 30% ratios of RPU-BF-T30 give the smallest pore diameter size. The peak of thermal degradation temperature of untreated and treated bamboo fiber was increased from 320°C to 350 °C with a weight loss of 80% to 50%. The treated bamboo fiber exhibited peaks at 3010–3040 cm-1 were associated with stronger Si-O-Si bonding, indicating the formation of new chemical bonds between bamboo fiber and silane coupling agent due to the ester bond from the cellulose, lignin, and hemicellulose. Thus, there was a similar trend peak in the functional chemical group in the FTIR spectrum of the RPU-BF composite. This result shows that RPU-BF composite had the potential of the optimum ratio of bamboo fiber as an insulation material for local communities and beneficial to the bamboo industry.
- 2 June 2024
- Published by Akademia Baru Publishing in Journal of Advanced Research in Applied Mechanics
- Vol. 117  (1) , 91-106
Open AccessMorphological, TGA, and FTIR on Rigid Polyurethane Composite Laminated with Untreated and Treated Bamboo Fiber Roof Insulation
The performance of roof insulation such as polyurethane decreased due to problems such as insufficient absorption and poor thermal insulation performance, especially during rainstorms. The aims of this study are to investigate the physical property and its potential reinforced material such as rigid polyurethane doped with treated and untreated bamboo fiber composite (RPU-BF) at different ratios of 0, 25, 30, 35, and 40% of bamboo fibers as an insulation material for roof applications. The bamboo fibers were treated by using silane coupling agent treatment. The rigid polyurethane composite samples were prepared and then laminated bamboo fiber to overcome the sound problem in roofs. The physical characterization was investigated by Water Contact Angle (WCA), the morphological by Scanning Electron Microscopy (SEM), Thermo-gravimetric Analysis (TGA), and Fourier Transform Infrared Spectroscopy (FTIR) Analysis. The results showed that the treated bamboo fiber had a 192.5° water contact angle as a super hydrophobic property due to the presence of the chemical bonds Si-O-Si and Si-O-C in the silane coupling agent treatment. The morphology showed that 30% ratios of RPU-BF-T30 give the smallest pore diameter size. The peak of thermal degradation temperature of untreated and treated bamboo fiber was increased from 320°C to 350 °C with a weight loss of 80% to 50%. The treated bamboo fiber exhibited peaks at 3010–3040 cm-1 were associated with stronger Si-O-Si bonding, indicating the formation of new chemical bonds between bamboo fiber and silane coupling agent due to the ester bond from the cellulose, lignin, and hemicellulose. Thus, there was a similar trend peak in the functional chemical group in the FTIR spectrum of the RPU-BF composite. This result shows that RPU-BF composite had the potential of the optimum ratio of bamboo fiber as an insulation material for local communities and beneficial to the bamboo industry.
- Open Access
- 19 July 2023
- Published by Akademia Baru Publishing in Journal of Advanced Research in Applied Sciences and Engineering Technology
- Vol. 31  (2) , 268-280
The Physical and Sound Absorption Property of Lightweight Rigid Polyurethane Composite Reinforced Bamboo Fiber for Roof Applications
Rigid polyurethane (RPU) foams as roof insulation have become increasingly popular in Southeast Asian countries and have been extensively used for absorbing sound and reducing noise because of their good sound damping, viscoelasticity, and low density. In this study, the RPU foam composite reinforced bamboo fiber was investigated by physical characterization by SEM, TGA, and FTIR, and the sound absorption was measured by the Impedance Tube Test. The morphology result of the RPU foam composite indicates the size of the diameter pore influenced the sound absorption by adding bamboo fiber as a filler. The thermal degradation of the presence of lignin in the bamboo fiber at the temperature range of 400 °C to 500 °C and the total weight loss is 76 % at 429 °C temperature. FTIR spectrum shows that the peak at 2890 to 2935 cm-1 are indicated –CH stretching vibrations and characteristics for bamboo fiber can be used in polymer composites. The sound absorption of RPU 25 foam composite reinforced bamboo fiber was found 0.74 absorbance at a frequency of 1250 Hz. RPU foam reinforced bamboo fiber as a filler has the highest transmission loss RPU 35 is 21 dB at a frequency range of 1600 Hz. The findings indicate by increasing the content of bamboo fiber as filler, the diameter of the open pore of RPU 25 and RPU 35 foam composite had the potential for sound absorption to absorb at low frequency to achieve greater sound absorption for roof insulation.
- 19 July 2023
- Published by Akademia Baru Publishing in Journal of Advanced Research in Applied Sciences and Engineering Technology
- Vol. 31  (2) , 268-280
Open AccessThe Physical and Sound Absorption Property of Lightweight Rigid Polyurethane Composite Reinforced Bamboo Fiber for Roof Applications
Rigid polyurethane (RPU) foams as roof insulation have become increasingly popular in Southeast Asian countries and have been extensively used for absorbing sound and reducing noise because of their good sound damping, viscoelasticity, and low density. In this study, the RPU foam composite reinforced bamboo fiber was investigated by physical characterization by SEM, TGA, and FTIR, and the sound absorption was measured by the Impedance Tube Test. The morphology result of the RPU foam composite indicates the size of the diameter pore influenced the sound absorption by adding bamboo fiber as a filler. The thermal degradation of the presence of lignin in the bamboo fiber at the temperature range of 400 °C to 500 °C and the total weight loss is 76 % at 429 °C temperature. FTIR spectrum shows that the peak at 2890 to 2935 cm-1 are indicated –CH stretching vibrations and characteristics for bamboo fiber can be used in polymer composites. The sound absorption of RPU 25 foam composite reinforced bamboo fiber was found 0.74 absorbance at a frequency of 1250 Hz. RPU foam reinforced bamboo fiber as a filler has the highest transmission loss RPU 35 is 21 dB at a frequency range of 1600 Hz. The findings indicate by increasing the content of bamboo fiber as filler, the diameter of the open pore of RPU 25 and RPU 35 foam composite had the potential for sound absorption to absorb at low frequency to achieve greater sound absorption for roof insulation.
- Open Access
Production Inventory Optimization Considering Direct and Indirect Carbon Emissions under a Cap-and-Trade Regulation
Background: The latest global agreement on net-zero emissions encourages new studies on production inventory optimization that promote carbon emissions reduction without harming a company’s profit performance, particularly because certain carbon-pricing regulations bind manufacturing companies. Methods: This study aims to develop a production inventory model that considers direct and indirect emissions in three emission scopes. It incorporates emissions from production, material handling, transportation, and waste disposal for further treatment under a carbon cap-and-trade regulation. With the help of Maple software, a convex total cost function was solved. Results: The results show that the optimum production quantity depends on the values of demand, setup cost, holding cost, fixed cost per delivery, fixed cost for waste disposal, and other parameters related to carbon prices. This study also found that the total cost was highly dependent on the values of the carbon cap, carbon price, and delivery distance. Meanwhile, changes in the delivery distance and fuel emissions standard significantly impacted total emissions. Conclusions: The proposed model can guide manufacturing companies in setting the optimum production quantity per cycle. Moreover, they must carefully manage the delivery and setting of the carbon cap and carbon price from the government.
Open AccessProduction Inventory Optimization Considering Direct and Indirect Carbon Emissions under a Cap-and-Trade Regulation
Background: The latest global agreement on net-zero emissions encourages new studies on production inventory optimization that promote carbon emissions reduction without harming a company’s profit performance, particularly because certain carbon-pricing regulations bind manufacturing companies. Methods: This study aims to develop a production inventory model that considers direct and indirect emissions in three emission scopes. It incorporates emissions from production, material handling, transportation, and waste disposal for further treatment under a carbon cap-and-trade regulation. With the help of Maple software, a convex total cost function was solved. Results: The results show that the optimum production quantity depends on the values of demand, setup cost, holding cost, fixed cost per delivery, fixed cost for waste disposal, and other parameters related to carbon prices. This study also found that the total cost was highly dependent on the values of the carbon cap, carbon price, and delivery distance. Meanwhile, changes in the delivery distance and fuel emissions standard significantly impacted total emissions. Conclusions: The proposed model can guide manufacturing companies in setting the optimum production quantity per cycle. Moreover, they must carefully manage the delivery and setting of the carbon cap and carbon price from the government.
- Open Access
- 14 September 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12  (18) , 9192
Setting Temperature and Humidity with a Misting System in a Pilot Greenhouse at Cisauk-Tangerang, Indonesia
A modern agricultural method of cultivating mustard greens and watercress with a hydroponic system in a pilot greenhouse has been implemented by a group of farmers in Cisauk-Tangerang, Banten, Indonesia. The characteristic tropical climate south of the equator causes high temperatures and humidity in the greenhouse. This study aims to control the temperature and humidity in the greenhouse using the misting method so that the temperature and humidity are not more than 33 °C and 85%, respectively. A misting system designed by the main equipment consists of a water flow control pump, temperature and humidity sensors, water mist spray nozzles, and water flow settings for intermittent drizzle for five minutes ON and ten minutes OFF using the internet of things module program. In addition to setting the water discharge intermittently, another limitation for the pump to be OFF is a minimum temperature benchmark of 28 °C and a maximum humidity of 85%. The temperature does not exceed 33 °C, and the humidity setting of 85% is obtained by adjusting the mass flow of water during the day according to the time sequence from 7 a.m. to 5 p.m.: 7 a.m. to 8 a.m. using 50 L/h, 8 a.m. to 10 a.m. using 60 L/h, 10 a.m. to 11 a.m. using 100 L/h, 11 a.m. to 1 p.m. using 120 L/h, 1 p.m. to 2 p.m. using 80 L/h, 2 p.m. to 3 p.m. using 60 L/h, and 3 p.m. and after using 0 L/h or the misting system is turned off.
- 14 September 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12  (18) , 9192
Open AccessSetting Temperature and Humidity with a Misting System in a Pilot Greenhouse at Cisauk-Tangerang, Indonesia
A modern agricultural method of cultivating mustard greens and watercress with a hydroponic system in a pilot greenhouse has been implemented by a group of farmers in Cisauk-Tangerang, Banten, Indonesia. The characteristic tropical climate south of the equator causes high temperatures and humidity in the greenhouse. This study aims to control the temperature and humidity in the greenhouse using the misting method so that the temperature and humidity are not more than 33 °C and 85%, respectively. A misting system designed by the main equipment consists of a water flow control pump, temperature and humidity sensors, water mist spray nozzles, and water flow settings for intermittent drizzle for five minutes ON and ten minutes OFF using the internet of things module program. In addition to setting the water discharge intermittently, another limitation for the pump to be OFF is a minimum temperature benchmark of 28 °C and a maximum humidity of 85%. The temperature does not exceed 33 °C, and the humidity setting of 85% is obtained by adjusting the mass flow of water during the day according to the time sequence from 7 a.m. to 5 p.m.: 7 a.m. to 8 a.m. using 50 L/h, 8 a.m. to 10 a.m. using 60 L/h, 10 a.m. to 11 a.m. using 100 L/h, 11 a.m. to 1 p.m. using 120 L/h, 1 p.m. to 2 p.m. using 80 L/h, 2 p.m. to 3 p.m. using 60 L/h, and 3 p.m. and after using 0 L/h or the misting system is turned off.
- Open Access
Physical Properties of Glass-Fibre-Reinforced Polymer Filled with Alumina Trihydrate and Calcium Carbonate
Gutters made of glass-fibre-reinforced polymer (GFRP) are usually produced with a three-millimetre thickness. The fillers are mixed into unsaturated polyester (UP) resin, which is intended to make the composite material more affordable. This study aims to examine the effects of the addition of alumina trihydrate (ATH), calcium carbonate (CC), and a mixture of ATH and CC of 15 and 30 parts per hundredweight of resins (PHR) on the material properties of the three-millimetre-thick three-layered GFRP composites. The properties observed included physical properties, namely, specific gravity and water absorption, chemical properties such as burning rate, and mechanical properties such as hardness, flexural strength, and toughness. The effects of the fillers on the voids and interfacial bond between the reinforcing fibre and matrix were analysed using the flexural fracture observation through scanning electron microscopy (SEM). The results showed that the addition of fillers into the UP resin led to an increase in the density, hardness, flexural strength, modulus of elasticity, and toughness but a decrease in water absorption and burning rate in a horizontal position. This information can be helpful for manufacturers of gutters made of GFRP in selecting the appropriate constituent materials while considering the technical and economic properties.
Open AccessPhysical Properties of Glass-Fibre-Reinforced Polymer Filled with Alumina Trihydrate and Calcium Carbonate
Gutters made of glass-fibre-reinforced polymer (GFRP) are usually produced with a three-millimetre thickness. The fillers are mixed into unsaturated polyester (UP) resin, which is intended to make the composite material more affordable. This study aims to examine the effects of the addition of alumina trihydrate (ATH), calcium carbonate (CC), and a mixture of ATH and CC of 15 and 30 parts per hundredweight of resins (PHR) on the material properties of the three-millimetre-thick three-layered GFRP composites. The properties observed included physical properties, namely, specific gravity and water absorption, chemical properties such as burning rate, and mechanical properties such as hardness, flexural strength, and toughness. The effects of the fillers on the voids and interfacial bond between the reinforcing fibre and matrix were analysed using the flexural fracture observation through scanning electron microscopy (SEM). The results showed that the addition of fillers into the UP resin led to an increase in the density, hardness, flexural strength, modulus of elasticity, and toughness but a decrease in water absorption and burning rate in a horizontal position. This information can be helpful for manufacturers of gutters made of GFRP in selecting the appropriate constituent materials while considering the technical and economic properties.
- Open Access
- 12 May 2022
- Published by MDPI AG in Sustainability
- Vol. 14  (10) , 5862
A Novel Z Profile of Pultruded Glass-Fibre-Reinforced Polymer Beams for Purlins
Purlins made from galvanised steel in fertiliser warehouses have often been considered less efficient, necessitating a new purlin made using corrosion-resistant material to increase building efficiency. This study was an attempt to design a nine-metre purlin from glass-fibre-reinforced polymer (GFRP) composite material for a new fertiliser warehouse in Bontang-East Kalimantan, Indonesia. The purlin design selected in this study was the Z profile of pultruded beams from GFRP composite material that met the criteria of an efficient purlin, such as corrosion resistance, compact stacking, and ability to withstand technical loads. In particular, the Z profile becomes compact when stacked, and the GFRP material used is corrosion-resistant yet affordable. The primary materials for GFRP composites consist of long yarn glass fibre bundles for reinforcement and unsaturated polyester resin (UPR) for the matrix. Material strength modelling was based on analytical and finite element approaches. The analysis shows that the most considerable normal stress of “64.41 MPa” occurred at the two fixed end supports, while the most significant deflection of “45.9 mm” occurred at the mid-span of the purlin structure. The purlin structure was considered safe, as the strength and deflection were below the threshold. Thus, the Z profile of the pultruded purlin beams built using the GFRP composite material meets the technical criteria.
- 12 May 2022
- Published by MDPI AG in Sustainability
- Vol. 14  (10) , 5862
Open AccessA Novel Z Profile of Pultruded Glass-Fibre-Reinforced Polymer Beams for Purlins
Purlins made from galvanised steel in fertiliser warehouses have often been considered less efficient, necessitating a new purlin made using corrosion-resistant material to increase building efficiency. This study was an attempt to design a nine-metre purlin from glass-fibre-reinforced polymer (GFRP) composite material for a new fertiliser warehouse in Bontang-East Kalimantan, Indonesia. The purlin design selected in this study was the Z profile of pultruded beams from GFRP composite material that met the criteria of an efficient purlin, such as corrosion resistance, compact stacking, and ability to withstand technical loads. In particular, the Z profile becomes compact when stacked, and the GFRP material used is corrosion-resistant yet affordable. The primary materials for GFRP composites consist of long yarn glass fibre bundles for reinforcement and unsaturated polyester resin (UPR) for the matrix. Material strength modelling was based on analytical and finite element approaches. The analysis shows that the most considerable normal stress of “64.41 MPa” occurred at the two fixed end supports, while the most significant deflection of “45.9 mm” occurred at the mid-span of the purlin structure. The purlin structure was considered safe, as the strength and deflection were below the threshold. Thus, the Z profile of the pultruded purlin beams built using the GFRP composite material meets the technical criteria.
- Open Access
Industrial Implementation of Aluminum Trihydrate-Fiber Composition for Fire Resistance and Mechanical Properties in Glass-Fiber-Reinforced Polymer Roofs
It is difficult to obtain suitable fire resistance and mechanical properties for glass-fiber-reinforced polymer (GFRP) roof material in industrial applications. Although some efforts to improve the fire resistance properties of GFRP have been carried out, in practice this sometimes degrades the mechanical properties. Therefore, the base materials, such as filler and reinforcing fiber, must be appropriately combined to simultaneously improve both fire resistance and mechanical properties. The present study examines improvements in GFRP roof material by investigating the effect of aluminium trihydrate (ATH) as a filler and the combination of a chopped strand mat (CSM) with woven roving (WR) and stitched mat (STM) fibers as the reinforcement in a composite GFRP roof structure. The roof samples were prepared following industrial machine standards using the specified materials. The mechanical properties of GFRP were evaluated using tensile, flexural and impact tests, following ASTM D638, ASTM D790 and ASTM D256 standards, respectively. The fire properties were examined through fire tests following the ASTM D635 standard. The results show that the GFRP roof composed of CSM/WR fibers had a 40% higher tensile strength (103.5 MPa) compared with the GFRP roof without CSM fibers (73.8 MPa). The flexural strength of the GFRP roof with CSM/WR fibers was also 57% higher than the roof without fibers, with a ratio of 315.61 MPa to 201 MPa. With the use of CSM/WR fibers, the fire resistance also increased by 23%, resulting in a ratio of 4.31 mm/min to 5.32 mm/min. These results demonstrate that the combination of CSM/WR fibers as a reinforcement would be an excellent option for producing an improved GFRP roof with better industrial properties, especially when producing improved GFRP roofs using a continuous lamination machine.
Open AccessIndustrial Implementation of Aluminum Trihydrate-Fiber Composition for Fire Resistance and Mechanical Properties in Glass-Fiber-Reinforced Polymer Roofs
It is difficult to obtain suitable fire resistance and mechanical properties for glass-fiber-reinforced polymer (GFRP) roof material in industrial applications. Although some efforts to improve the fire resistance properties of GFRP have been carried out, in practice this sometimes degrades the mechanical properties. Therefore, the base materials, such as filler and reinforcing fiber, must be appropriately combined to simultaneously improve both fire resistance and mechanical properties. The present study examines improvements in GFRP roof material by investigating the effect of aluminium trihydrate (ATH) as a filler and the combination of a chopped strand mat (CSM) with woven roving (WR) and stitched mat (STM) fibers as the reinforcement in a composite GFRP roof structure. The roof samples were prepared following industrial machine standards using the specified materials. The mechanical properties of GFRP were evaluated using tensile, flexural and impact tests, following ASTM D638, ASTM D790 and ASTM D256 standards, respectively. The fire properties were examined through fire tests following the ASTM D635 standard. The results show that the GFRP roof composed of CSM/WR fibers had a 40% higher tensile strength (103.5 MPa) compared with the GFRP roof without CSM fibers (73.8 MPa). The flexural strength of the GFRP roof with CSM/WR fibers was also 57% higher than the roof without fibers, with a ratio of 315.61 MPa to 201 MPa. With the use of CSM/WR fibers, the fire resistance also increased by 23%, resulting in a ratio of 4.31 mm/min to 5.32 mm/min. These results demonstrate that the combination of CSM/WR fibers as a reinforcement would be an excellent option for producing an improved GFRP roof with better industrial properties, especially when producing improved GFRP roofs using a continuous lamination machine.