Christoph Becher
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Christoph Becher has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Anke Turger
Institute of Production Engineering and Machine Tools (IFW), Gottfried Wilhelm Leibniz Universität Hannover, An der Universität 2, 30823 Garbsen, Germany
1 shared publication - Arne Driessen
Institute for Research in Operative Medicine, Faculty of Health, Department of Medicine, Witten/Herdecke University, Ostmerheimer Str. 200, D-51109, Cologne, Germany.
1 shared publication - Berend Denkena
Institute of Production Engineering and Machine Tools, Leibniz Universität Hannover, 30823 Garbsen, Germany
1 shared publication - Bertil Bouillon
Department of Orthopaedic Surgery, Trauma Surgery and Sports Medicine, Cologne Merheim Medical Center Witten/Herdecke University Cologne Germany
1 shared publication - Christof Hurschler
Laboratory for Biomechanics and Biomaterials, Department of Orthopaedic Surgery, Hannover Medical School, Anna-von-Borries-Str. 1-7, 30625, Hannover, Germany
1 shared publication - Christoph Offerhaus
Department of Orthopedic Surgery and Sports Traumatology, Witten/Herdecke University, Sana Medical Centre, Cologne, Germany
1 shared publication
Latest Publications
- 1 April 2015
- Vol. 153 (2) , 132
[Total knee replacement - High benefit in terms of quality of life].
- Open Access
- 26 March 2014
- Published by Springer Nature in BMC Musculoskeletal Disorders
- Vol. 15 (1) , 100
The fabella syndrome - a rare cause of posterolateral knee pain: a review of the literature and two case reports
The purpose of this article was to evaluate the risks and benefits of non-operative treatment versus surgical excision of a fabella causing posterolateral knee pain. We performed a systematic review of literature and also present two case reports. Twelve publications were found in a PubMed literature review searching the word “fabella syndrome”. Non-operative treatment and surgical excision of the fabella has been described. Two patients presented to our outpatient clinic with persisting posterolateral knee pain. In both cases the presence of a fabella was identified, located in close proximity to the posterolateral femoral condyle. All other common causes of intra- and extra articular pathologies possibly causing the posterolateral knee pain were excluded. Following failure to respond to physiotherapy both patients underwent arthroscopy which excluded other possible causes for posterolateral knee pain. The decision was made to undertake surgical excision of the fabella in both cases without complication. Both patients were examined 6 month and one year after surgery with the Tegner activity score, the Visual Analogue Scale (VAS), and International Knee Documentation Committee Score (IKDC). Consistent posterolateral pain during exercise might indicate the presence of a fabella syndrome. Resecting the fabella can be indicated and is a minor surgical procedure with minimal risk. Despite good results in the literature posterolateral knee pain can persist and prevent return to a high level of sports. Level of evidence: IV, case reports and analysis of literature.
- 26 March 2014
- Published by Springer Nature in BMC Musculoskeletal Disorders
- Vol. 15 (1) , 100
Open AccessThe fabella syndrome - a rare cause of posterolateral knee pain: a review of the literature and two case reports
The purpose of this article was to evaluate the risks and benefits of non-operative treatment versus surgical excision of a fabella causing posterolateral knee pain. We performed a systematic review of literature and also present two case reports. Twelve publications were found in a PubMed literature review searching the word “fabella syndrome”. Non-operative treatment and surgical excision of the fabella has been described. Two patients presented to our outpatient clinic with persisting posterolateral knee pain. In both cases the presence of a fabella was identified, located in close proximity to the posterolateral femoral condyle. All other common causes of intra- and extra articular pathologies possibly causing the posterolateral knee pain were excluded. Following failure to respond to physiotherapy both patients underwent arthroscopy which excluded other possible causes for posterolateral knee pain. The decision was made to undertake surgical excision of the fabella in both cases without complication. Both patients were examined 6 month and one year after surgery with the Tegner activity score, the Visual Analogue Scale (VAS), and International Knee Documentation Committee Score (IKDC). Consistent posterolateral pain during exercise might indicate the presence of a fabella syndrome. Resecting the fabella can be indicated and is a minor surgical procedure with minimal risk. Despite good results in the literature posterolateral knee pain can persist and prevent return to a high level of sports. Level of evidence: IV, case reports and analysis of literature.
- Open Access
- 1 January 2013
- Published by Springer Nature in BioMedical Engineering OnLine
- Vol. 12 (1) , 84
Manufacturing conditioned roughness and wear of biomedical oxide ceramics for all-ceramic knee implants
Ceramic materials are used in a growing proportion of hip joint prostheses due to their wear resistance and biocompatibility properties. However, ceramics have not been applied successfully in total knee joint endoprostheses to date. One reason for this is that with strict surface quality requirements, there are significant challenges with regard to machining. High-toughness bioceramics can only be machined by grinding and polishing processes. The aim of this study was to develop an automated process chain for the manufacturing of an all-ceramic knee implant. A five-axis machining process was developed for all-ceramic implant components. These components were used in an investigation of the influence of surface conformity on wear behavior under simplified knee joint motion. The implant components showed considerably reduced wear compared to conventional material combinations. Contact area resulting from a variety of component surface shapes, with a variety of levels of surface conformity, greatly influenced wear rate. It is possible to realize an all-ceramic knee endoprosthesis device, with a precise and affordable manufacturing process. The shape accuracy of the component surfaces, as specified by the design and achieved during the manufacturing process, has a substantial influence on the wear behavior of the prosthesis. This result, if corroborated by results with a greater sample size, is likely to influence the design parameters of such devices.
- 1 January 2013
- Published by Springer Nature in BioMedical Engineering OnLine
- Vol. 12 (1) , 84
Open AccessManufacturing conditioned roughness and wear of biomedical oxide ceramics for all-ceramic knee implants
Ceramic materials are used in a growing proportion of hip joint prostheses due to their wear resistance and biocompatibility properties. However, ceramics have not been applied successfully in total knee joint endoprostheses to date. One reason for this is that with strict surface quality requirements, there are significant challenges with regard to machining. High-toughness bioceramics can only be machined by grinding and polishing processes. The aim of this study was to develop an automated process chain for the manufacturing of an all-ceramic knee implant. A five-axis machining process was developed for all-ceramic implant components. These components were used in an investigation of the influence of surface conformity on wear behavior under simplified knee joint motion. The implant components showed considerably reduced wear compared to conventional material combinations. Contact area resulting from a variety of component surface shapes, with a variety of levels of surface conformity, greatly influenced wear rate. It is possible to realize an all-ceramic knee endoprosthesis device, with a precise and affordable manufacturing process. The shape accuracy of the component surfaces, as specified by the design and achieved during the manufacturing process, has a substantial influence on the wear behavior of the prosthesis. This result, if corroborated by results with a greater sample size, is likely to influence the design parameters of such devices.