KKKamil Krpec

Kamil Krpec

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Kamil Krpec has a total of 38 co-authors. Here are the top co-authors by number of shared publications:

  • Jiří Horák

    Centre for Energy and Environmental Technologies, Energy Research Centre, VSB—Technical University of Ostrava, 17. listopadu 2172/15, 708 00 Ostrava, Czech Republic

    9 shared publications
  • František Hopan

    Centre for Energy and Environmental Technologies, Energy Research Centre, VSB—Technical University of Ostrava, 17. listopadu 2172/15, 708 00 Ostrava, Czech Republic

    8 shared publications
  • Jiří Ryšavý

    Energy Research Centre, Centre for Energy and Environmental Technologies, VŠB—Technical University of Ostrava, 17. Listopadu 2172/15, 708 00 Ostrava, Czech Republic

    4 shared publications
  • Lenka Kuboňová

    Centre for Energy and Environmental Technologies, Energy Research Centre, VSB—Technical University of Ostrava, 17. listopadu 2172/15, 708 00 Ostrava, Czech Republic

    4 shared publications
  • Oleksandr Molchanov

    Centre for Energy and Environmental Technologies, Energy Research Centre, VSB—Technical University of Ostrava, 17. listopadu 2172/15, 708 00 Ostrava, Czech Republic

    4 shared publications
  • Petr Kubesa

    VŠB - Technical University Ostrava, Energy research center, 17. listopadu 15/2172, 708 33 Ostrava - Poruba, Czech Republic

    3 shared publications

Latest Publications

  • Open Access

    The Genotoxic Potential of Organic Emissions from Domestic Boilers Combusting Biomass and Fossil Fuels

    by Jitka Sikorova, Frantisek Hopan, Lenka Kubonova, Jiri Horak, Alena Milcova, Pavel Rossner, Antonin Ambroz, Kamil Krpec, Oleksandr Molchanov, Tana Zavodna

    Solid fuels are still widely used in household heating in Europe and North America. Emissions from boilers are released in proximity to people. Therefore, there is a need to minimise the toxicity of emissions affecting human health to the greatest extent possible. This study compares the genotoxic potential of the emissions of four boilers of modern and old design (automatic, gasification, down-draft, over-fire) operating at reduced output to simulate the real-life combustion fed by various fossil and renewable solid fuels (hard coal, brown coal, brown coal briquettes, wood pellets, wet and dry spruce). Organic emissions were tested for genotoxic potential by analysing bulky DNA adducts and 8-oxo-dG adduct induction. There was no consistent genotoxic pattern among the fuels used within the boilers. Genotoxicity was strongly correlated with polycyclic aromatic hydrocarbon (PAH) content, and even stronger correlation was observed with particulate matter (PM). In all measured variables (PM, PAHs, genotoxicity), the technology of the boilers was a more important factor in determining the genotoxic potential than the fuels burned. The highest levels of both bulky and 8-oxo-dG DNA adducts were induced by organics originating from the over-fire boiler, while the automatic boiler exhibited genotoxic potential that was ~1000- and 100-fold lower, respectively.


  • Open Access

    Transformation of NO in Combustion Gases by DC Corona

    by Oleksandr Molchanov, Kamil Krpec, Jiří Horák, Lenka Kuboňová, František Hopan, Jiří Ryšavý, Marcelina Bury

    This study investigates the performance of DC corona discharge electrostatic precipitators (ESPs) for NO conversion to increase DeNOx technologies’ efficiency for small-scale biomass combustion systems. Experiments were conducted using a 5 kW automatic wood pellet domestic heat source with combustion gas treated in a specially designed ESP operated in both positive and negative corona modes, resulting in a reduction in NO concentrations from 130 mg/m3 to 27/29 mg/m3 for positive/negative polarities (at 0 °C and 101.3 kPa). NO conversion efficiency was evaluated across a range of specific input energies (SIEs) from 0 to 50 J/L. The results demonstrate that DC corona ESPs can achieve up to 78% NO reduction, with positive corona demonstrating a greater energy efficiency, requiring a lower SIE (35 J/L) compared to the negative corona mode (48 J/L). A detailed analysis of reaction pathways revealed distinct conversion mechanisms between the two modes. In positive corona, dispersed active species distribution led to more uniform NO conversion, while negative corona exhibited concentrated reaction zones with about 20% higher ozone production. The reactions involving O and OH radicals were more important in positive corona, whereas ozone-mediated oxidation dominated in negative corona. The research results demonstrate that ESP technology with DC corona offers a promising, energy-efficient solution for NOx control in small-scale combustion systems.

  • Open Access

    Application End Evaluation of Electrostatic Precipitation for Control PM and NOx Emissions from Small-Scale Combustions

    by Oleksandr Molchanov, Kamil Krpec, Jiří Horák, Lenka Kuboňová, František Hopan, Jiří Ryšavý

    Electrostatic precipitators (ESPs) have shown promise in reducing particulate matter (PM) emissions, but their potential for simultaneous NOx reduction in small-scale combustion systems remains underexplored. This study focuses on using non-thermal plasma generated in a corona discharge to reduce PM and NOx emissions from small-scale combustion. ESP was specifically designed for a commercially available 15 kW boiler with wood pellet combustion and used with both positive and negative discharge polarity to control emissions without any chemical additives. ESP performance was evaluated across a range of specific input energies (SIE) in terms of particle mass and number concentrations and NOx concentrations obtained by continuous gas analysis. ESP ensured the reduction in PM concentrations from 48 mg/m3 to the magnitude of PM content in the ambient air. The highest precipitation efficiency was observed for particles in the 20–200 nm range. Concurrently, NOx emissions were reduced by up to 78%, from 178 mg/m3 to 39 mg/m3. These results were achieved at specific input energies of 36 for positive and 48 J/L for negative corona, which is significantly lower than those reported for many existing separate PM and NOx control systems. This study demonstrates the potential of ESPs as a compact, energy-efficient solution for simultaneous PM and NOx removal in small-scale combustion systems, offering promising implications for improving air pollution control technologies for small-scale combustion systems.


  • Open Access

    The Effect of Wood Species on Fine Particle and Gaseous Emissions from a Modern Wood Stove

    by Henna Rinta-Kiikka, Karna Dahal, Juho Louhisalmi, Hanna Koponen, Olli Sippula, Kamil Krpec, Jarkko Tissari

    Residential wood combustion (RWC) is a significant source of gaseous and particulate emissions causing adverse health and environmental effects. Several factors affect emissions, but the effects of the fuel wood species on emissions are currently not well understood. In this study, the Nordic wood species (named BirchA, BirchB, Spruce, SpruceDry, Pine and Alder) were combusted in a modern stove, and the emissions were studied. The lowest emissions were obtained from the combustion of BirchA and the highest from Spruce and Alder. The fine particle mass (PM2.5) was mainly composed of elemental carbon (50–70% of PM2.5), which is typical in modern appliances. The lowest PAH concentrations were measured from BirchA (total PAH 107 µg/m3) and Pine (250 µg/m3). In the ignition batch, the PAH concentration was about 4-fold (416 µg/m3). The PAHs did not correlate with other organic compounds, and thus, volatile organic compounds (VOCs) or organic carbon (OC) concentrations cannot be used as an indicator of PAH emissions. Two birch species from different origins with a similar chemical composition but different density produced partially different emission profiles. This study indicates that emission differences may be due more to the physical properties of the wood and the combustion conditions than to the wood species themselves.


  • Open Access

    Comparative Analysis of Real-Emitted Particulate Matter and PM-Bound Chemicals from Residential and Automotive Sources: A Case Study in Poland

    by Katarzyna Szramowiat-Sala, Katarzyna Styszko, Lucyna Samek, Magdalena Kistler, Mariusz Macherzyński, Jiří Ryšavý, Kamil Krpec, Jiří Horák, Anne Kasper-Giebl, Janusz Gołaś

    The awareness of environmental pollution has been continuously growing in recent decades and is currently reaching its maximum. Europe and most developed countries are determined to ensure safe breathing air for their citizens, and the measures to do so are stricter than ever before. Combustion procedures remain the primary means of producing energy and warmth in Poland. Among the notable constituents of flue gases produced as a result of fuel combustion, solid particles (or particulate matter) hold significant prominence. The paper presents the chemical characterisation of particulate matter emitted from stationary and automotive emission sources. Stationary emission sources included the combustion process of fossil fuels (soft wood, bituminous coal, ecopea coal, culm) in domestic heating units and the process of combustion of bituminous coal in a power plant. Automotive emission sources included light duty and medium duty vehicles fuelled by diesel. Exhaust toxicity tests were carried out maintaining the real conditions of PM emission. In all field measurements particulate matter was gravimetrically measured and collected on quartz or glass fibre filters. Subsequently, the content of carbonaceous fraction, inorganic ions, and metals and metalloids was analyzed using different analytical techniques. The chemical composition of the particulate matter differed depending on the emission source. With respect to stationary combustion sources, the main factors determining solid particle emission are related primarily to the fuel quality. The duty of vehicles was also a factor that influenced the chemical characterisation of the particulate matter emitted from the engines.


  • Open Access

    Specifics of Electrostatic Precipitation of Fly Ash from Small-Scale Fossil Fuel Combustion

    by Oleksandr Molchanov, Kamil Krpec, Jiří Horák, Tadeaš Ochodek, Milan Dej, Lenka Kubonová, František Hopan, Jiří Ryšavý

    This paper investigates the removal efficiency of a honeycomb electrostatic precipitator (ESP) applied to control particulate matter (PM) emissions from a small-scale boiler with combustion lignite and hard coal. The specifics of the precipitation of emissions from small-scale boilers are discussed, and the design principles for relevant ESPs are presented and used. The ion-induced nucleation of sulfuric acid occurred, causing the drastic penetration of 19 nm particles through the ESP. Despite this, the overall collection efficiency was sufficient to meet the EU’s Ecodesign Directive requirements. Back corona was not detected. The optimal ESP performance is defined with further parameters: a current density of 0.5 mA/m2 at an electric field strength of about 2.7 × 105 V/m; a minimal specific collecting area of ESP (SCA) of 60 m2/(m3/s); and Nt-product of 4.5 × 1014 s/m3. Such parameters of ESPs should ensure adequate PM emissions control for any type of boiler with similar emissions characteristics. The composition of collected fly ash particles was analysed, and a method for fly ash utilisation was proposed. This research may be helpful for designing ESPs to control PM emissions for small-scale units with fossil fuel combustion.


  • Production of dioxins and furans for various solid fuels burnt in 25 kW automatic boiler

    by František Hopan, Jiří Horák, Kamil Krpec, Petr Kubesa, Milan Dej, Vendula Laciok

    There has been brown coal, black coal and maize straw in a pellet form burnt in an automatic boiler. Production of dibenzodioxins and dibenzofuranes, recomputated through toxicity equivalents, expressed as the emission factor relative to the fuel unit, has differentiated in a range of ca. three orders (0.05 up to 78.9 ng/kg) in dependence on a sort of the used fuel. The measured values have been compared with emission factors used for the emission inventory in the Czech Republic and Poland and with the emission limit applicable for waste incineration plants. The study has proven the influence of chlorine content in fuel on production of dioxins and furanes.

  • Aerosols and the methods of determining the characteristics of nanoparticles

    by Mária Skřínská, Jiří Horák, Pavel Danihelka, Kamil Krpec, František Hopan, Zdeňka Kaličáková, Petr Kubesa, Lubomír Martiník, Vendula Drastichová, Jan Skřínský, et al.

    The purpose of this paper is to address the issue of aerosols by defining and dividing them in terms of their size, spatial localization and composition. The paper briefly deals with the issue of the origins and formation of aerosols. Further, it describes the trends in measuring nanoparticles based on their electric field mobility behavior, condensation, optical properties and aerosol particle acceleration in an air-stream.


  • Emission of nanoparticles during combustion of waste biomass in fireplace

    by Vendula Drastichová, Kamil Krpec, Jiří Horák, František Hopan, Petr Kubesa, Lubomír Martiník, Jan Koloničný, Tadeáš Ochodek, Michal Holubčík

    Contamination of air by solid particles is serious problem for human health and also environment. Small particles in nano-sizes are more dangerous than same weight of larger size. Negative effect namely of the solid particles depends on (i) number, (ii) specific surface area (iii) respirability and (iv) bonding of others substances (e.g. PAHs, As, Cd, Zn, Cu etc.) which are higher for smaller (nano-sizes) particles compared to larger one. For this reason mentioned above this contribution deals with measuring of amount, and distribution of nanoparticles produced form combustion of waste city biomass in small combustion unit with impactor DLPI.