VVViliam Vretenár

Viliam Vretenár

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Viliam Vretenár has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Thermal properties of Oak high density board measured by the pulse transient method for different heat pulse energy

    by Vlastimil Boháč, Rupali Tiwari, Luboš Krišťák, Luigi Todaro, Valentina Lo Giudice, Viliam Vretenár

    The energy efficiency of buildings is assessed on the base of thermal insulation properties that can help to save energy costs as well as environment. The wooden materials are widely used as they become significantly recyclable and nature-friendly. Their thermal insulation properties have to be known for construction purposes. The modern experimental methods for the Thermophysical measurements are highly desired in this field. The methodology for the experimental measurement setup has to be optimized and possible disturbing effects at measurements have to be taking into account. The first more sophisticated method is to include disturbing effect into the model or to use the second one by arrangement of the sample set geometry as close as possible to the ideal state. The pulse transient method is relatively fast in comparison with stationary methods. It is simple for experimental arrangement and reliable for large scale of materials. Measurement reliability in this paper was tested by increasing the heat pulse energy, as the estimated Thermophysical parameters have to be independent on used power. The data scattering found for all measurements was found below 2% for all Thermophysical parameters.


  • The transient method measurements of thermophysical properties of non-solid clay loam

    by Vlastimil Boháč, Peter Dieška, Viliam Vretenár, Ján Hudec, Vladimír Lukáč

    The In the frame of extending the renewable energy systems, the use of the shallow geological bedrock below the houses is used for the seasonal heat storage purposes. Thus, the knowledge of the thermophysical properties of the soft clay loam materials present in the bedrock is important. On the basis of the known thermal diffusivity, thermal conductivity and specific heat of the materials around the energetic needle, one can calculate the time dependency of the heat dissipated and transferred into the surrounding. This allows calculating the temperature maps that can specify in more detail the heat penetration depth during the seasonal storage and pumping out of the heat accumulated during the year seasons. The aim is to optimize the efficiency of the system. The clay loams in the free nature contain high level of the moisture and thus have high values of specific heat. The pulse transient method was used to get the thermophysical parameters of these materials. Specimens were drilled out from the bedrock at depths 50, 150 and 250cm from the surface. The measured values of equilibrium sorption moisture show that obtained materials are very different. In the paper we show the possible influence of the redistribution of water content during the shooting of the heat pulse. The water redistribution deforms the temperature response. This effect was avoided by lowering the heat pulse power to minimal values that still allows the evaluation of the measurement.

  • Hot tube method for the measuring of thermophysical properties of materials

    by Peter Dieška, Vlastimil Boháč, Viliam Vretenár

    The measurement of thermal properties of materials that do not keep the form is problematic, because usually, the basic condition of the most models predicts constant dimensions. The plastic materials like clay or loam in natural condition always contain some water and thus are viscous and squeeze out of specimen holder when clamped even at weak force produced by specimen holder. Thus, the specimen dimensions are changing in during the measurement when it is not placed in a solid container. Even at this arrangement the shrinkage of material at the measurements causes the lowering the specimen thickness when using two probe method like pulse transient technique. This effect problem could be lowered or neglected at single probe techniques like the planar hot disk or this newly derived hot tube method. Hot tube method is derived for the probe made as the rectangular plane bended around the solid cylinder or tube made of thermally low conducting material. The probe generates the heat and the rate of temperature rise in it is driven by heat transfer ability of the measured surrounding material. Such a probe should be used in laboratory as well as in the field conditions.

  • New way of measurement of thermophysical properties of clay loam materials by transient methods

    by Vlastimil Boháč, Peter Dieška, Viliam Vretenár, Vladimír Lukáč

    The problem of the measurement of clay loam materials in plastic consistency is more or less difficult as they can change the shape during the long time measurements. The specimen thickness is expected as the constant during all the experiment measured by transient pulse method. In a case of plastic clay loam, it can change the form during the measurement because of the squeeze of the material even under the gravity condition. Thus the specimen surface wall should be reinforced by special dimensionally well-defined thin wall container. In this paper the special container in a form of thin tube rings bounded by central annular ring was constructed and used for the measurements. The heat source was inserted into the tube rings through the nozzle in the middle part and the thermocouple was inserted through the drilled openings at defined distance from the heat source. System clamped the heat source together with the rings at desired distance from the thermocouple. This distance represents the thickness of tested specimen. The soft plastic material fill the inner space of tube rings in such a way to fulfill the geometry conditions for this method. The need of soft clay loam material measurement is to test its thermal properties because of the interest to use it as the heat storage material below the buildings. The measured clay loam containing some moisture has quite high values of specific heat and thus the use of it as the heat storage material is promising.