Pavel Florian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Pavel Florian has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Oldrich Zmeskal
Faculty of Chemistry, Brno University of Technology, Purkyňova 464/118, 612 00 Brno, Czech Republic
4 shared publications - Katerina Valentova
Faculty of Chemistry, Brno University of Technology, Purkyňova 118, 612 00 Brno, Czech Republic
2 shared publications - Lucie Trhlikova
Faculty of Chemistry, Brno University of Technology, 612 00 Brno, Czech Republic
2 shared publications - Lukáš Fiala
Department of Materials Engineering and Chemistry, Faculty of Civil Engineering, Czech Technical University in Prague, Thákurova 7, 166 29 Prague 6, Czech Republic
2 shared publications - Petr Psencik
CEITEC, Brno University of Technology, 612 00 Brno, Czech Republic
1 shared publication Radek Prikryl
Brno University of Technology
1 shared publication
Latest Publications
- 10 July 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1978 (1) , 250002
Correlation between dielectric and thermal properties of alkali-activated aluminosilicates with carbon fiber admixture
The paper deals with the comparison of the thermal and dielectric properties of alkali-activated aluminosilicates containing the conductive admixture in the form of carbon fibers. To determine the thermal conductivity and thermal capacity of the system, a differential method based on the response to the step wise heating was used. The electrical conductivity and the capacities were determined by impedance spectroscopy. For both electrical and thermal properties, a model was created which allowed the determination of the characteristics of individual processes. The analysis of these models showed that the thermal conductivity of material decreases with increasing concentration of admixtures, probably because of greater porosity of material. For the concentration of 2.22% it is about three times smaller than for the concentration of 0.11%. The heat capacity is reduced at concentrations higher than 1.11%. The electrical conductivity decreases with increasing concentration of the admixture, which again seems to be related to greater porosity of material. For the concentration of 2.22% it is more than four times smaller than for the concentration of 0.11%.
- 10 July 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1978 (1) , 250002
Correlation between dielectric and thermal properties of alkali-activated aluminosilicates with carbon fiber admixture
The paper deals with the comparison of the thermal and dielectric properties of alkali-activated aluminosilicates containing the conductive admixture in the form of carbon fibers. To determine the thermal conductivity and thermal capacity of the system, a differential method based on the response to the step wise heating was used. The electrical conductivity and the capacities were determined by impedance spectroscopy. For both electrical and thermal properties, a model was created which allowed the determination of the characteristics of individual processes. The analysis of these models showed that the thermal conductivity of material decreases with increasing concentration of admixtures, probably because of greater porosity of material. For the concentration of 2.22% it is about three times smaller than for the concentration of 0.11%. The heat capacity is reduced at concentrations higher than 1.11%. The electrical conductivity decreases with increasing concentration of the admixture, which again seems to be related to greater porosity of material. For the concentration of 2.22% it is more than four times smaller than for the concentration of 0.11%.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1863, 040012
Thermal properties of alkali-activated aluminosilicates
The paper is focused on measurements and evaluation of thermal properties of alkali-activated aluminosilicates (AAA) with various carbon admixtures. Such composites consisting of blast-furnace slag, quartz sand, water glass as alkali activator and small amount of electrically conductive carbon admixture exhibit better electric and thermal properties than the reference material. Such enhancement opens up new practical applications, such as designing of snow-melting, de-icing or self-sensing systems that do not need any external sensors to detect current condition of building material. Thermal properties of the studied materials were measured by the step-wise transient method and mutually compared.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1863, 040012
Thermal properties of alkali-activated aluminosilicates
The paper is focused on measurements and evaluation of thermal properties of alkali-activated aluminosilicates (AAA) with various carbon admixtures. Such composites consisting of blast-furnace slag, quartz sand, water glass as alkali activator and small amount of electrically conductive carbon admixture exhibit better electric and thermal properties than the reference material. Such enhancement opens up new practical applications, such as designing of snow-melting, de-icing or self-sensing systems that do not need any external sensors to detect current condition of building material. Thermal properties of the studied materials were measured by the step-wise transient method and mutually compared.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1752 (1) , 040027
Study of the thermal properties of filaments for 3D printing
Various materials are used for 3D printing, most commonly Acrylonitrile butadiene styrene (ABS), Polylactic acid (PLA), Polyethylene (PET) and Polypropylene (PP). These materials differ mainly in their melting point, which significantly influences the properties of the final products. Filaments are melted in the print head during the printing process. The temperature range is from 150 °C to 250 °C depending on the technology used. The optimum temperature for the cooling substrate on which printing is carried out is chosen so as to ensure uniform cooling and deformation. It generally varies between (40 – 100) °C. From the above it is clear that both temperatures can significantly affect the properties of the printed 3D object. It is therefore important to determine the thermal parameters (thermal conductivity, specific heat and thermal diffusivity) of the materials used across the entire range of temperatures. For evaluating the properties of different types of PLA materials, the step transient method was used, which allows determination of all required parameters using a fractal heat transfer model.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1752 (1) , 040027
Study of the thermal properties of filaments for 3D printing
Various materials are used for 3D printing, most commonly Acrylonitrile butadiene styrene (ABS), Polylactic acid (PLA), Polyethylene (PET) and Polypropylene (PP). These materials differ mainly in their melting point, which significantly influences the properties of the final products. Filaments are melted in the print head during the printing process. The temperature range is from 150 °C to 250 °C depending on the technology used. The optimum temperature for the cooling substrate on which printing is carried out is chosen so as to ensure uniform cooling and deformation. It generally varies between (40 – 100) °C. From the above it is clear that both temperatures can significantly affect the properties of the printed 3D object. It is therefore important to determine the thermal parameters (thermal conductivity, specific heat and thermal diffusivity) of the materials used across the entire range of temperatures. For evaluating the properties of different types of PLA materials, the step transient method was used, which allows determination of all required parameters using a fractal heat transfer model.
- 23 October 2015
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1126, 181-186
Thermal Properties of Mannitol Derivative
Mannitol is an alcoholic sugar that is commonly used in the food industry. It is a white, odorless crystalline powder. Its melting temperature is about 168 °C. It is possible to be used also for the accumulation of energy in the heat exchangers based on oils. On its basis is sold a product PlusICE A164 of company PCM Products Ltd. (T = 164 °C, cp = 2.42 kJ.K-1 kg-1). Thermal properties of the material in both, solid and liquid phase were investigated for this purpose in terms of potential applications. Temperature dependence of thermal parameters (thermal diffusivity, thermal conductivity, and specific heat) were determined using a transient (step-wise) method. Fractal model of heat transport was used for the determination of thermal parameters. This model is independent on the geometry and on the type of the sample heating, and includes heat losses too. The experiment confirms the phase change temperature about 168 °C.
- 23 October 2015
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1126, 181-186
Thermal Properties of Mannitol Derivative
Mannitol is an alcoholic sugar that is commonly used in the food industry. It is a white, odorless crystalline powder. Its melting temperature is about 168 °C. It is possible to be used also for the accumulation of energy in the heat exchangers based on oils. On its basis is sold a product PlusICE A164 of company PCM Products Ltd. (T = 164 °C, cp = 2.42 kJ.K-1 kg-1). Thermal properties of the material in both, solid and liquid phase were investigated for this purpose in terms of potential applications. Temperature dependence of thermal parameters (thermal diffusivity, thermal conductivity, and specific heat) were determined using a transient (step-wise) method. Fractal model of heat transport was used for the determination of thermal parameters. This model is independent on the geometry and on the type of the sample heating, and includes heat losses too. The experiment confirms the phase change temperature about 168 °C.