DLDanko van der Laan

Danko van der Laan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Danko van der Laan has a total of 323 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Fabrication and test of a 6-tesla-class high-temperature superconducting dipole magnet at 4.2 K

    by Dmytro Abraimov, Diego Arbelaez, Lucas Brouwer, Jean-François Croteau, Joseph DiMarco, Paolo Ferracin, William B. Ghiorso, Hugh C. Higley, Mariusz Juchno, Andy Lin, et al.

    Superconducting magnets enable energy-frontier accelerators by generating strong magnetic fields to steer and focus the particles. Although high-temperature superconductors such as REBa 2 Cu 3 O x (, RE = rare earth) hold a strong potential for generating a higher magnetic field than Nb-Ti and Nb 3 Sn , the associated magnet and conductor technology for accelerator applications is still in its infancy. The U.S. Magnet Development Program is developing magnet technology in collaboration with industry. Here we report an experiment of making a dipole magnet called C3 using commercial high-temperature superconducting wires. The magnet, following a canted cos θ design, generated a dipole field of 5.99 T at 4.2 K in its clear aperture of 65 mm at 6.795 kA when a resistive voltage of 105 μ V appeared across one of the coils in the magnet. The stored energy was 53 kJ at the peak field. The magnet showed no degradation in the current-carrying capability at 4.2 K after the thermal cycle. We report on the detailed design, fabrication, and performance of the C3 magnet that can be of interest to potential users of this emerging technology. We also discuss issues and research needs to inform future magnet development. The experiment represented another step to addressing if the high-temperature superconducting accelerator magnet technology can increase the discovery capability of future particle accelerators.

  • Open Access

    Roadmap to Electrification of Transportation Systems Enabled by Superconducting Technology

    by Wenjuan Song, Mohammad Yazdani-Asrami, Ziad Melhem, Sergey Samoilenkov, Sergey Lee, Matthew A Rindfleisch, Mike J Tomsic, David Wayne Doll, Chris Kovacs, Xuan Peng, et al.

    Superconductivity was discovered more than a century ago, and it has achieved full commercialization for MRI and NMR applications. Superconducting technology has got on spotlight recent years for transportation, power network, and fusion energy, due to the significant advantages offered against its counterpart technologies, including lighter weight, compacter size, lower losses, higher efficiency, and higher power density. Therefore, many superconducting applications are moving towards higher technology readiness levels, with a fast pace. The accelerated research around superconducting applications for modern transportation is due to unique features of this technology towards decarbonisation via electrified systems. Meeting the Net Zero targets to decelerate global warming issue is the main driver of implementing the superconducting technology for aerospace, marine, and railway transport. However, many challenges still remain to be addressed for superconducting devices and applications, which will in turn pave the way for the commercialization of superconducting technology. In this article, a roadmap on electrification of transportation systems for aerospace, marine, and railway application is presented, covering challenges and solutions in design analysis, modelling, monitoring, and operation. A series of short articles are presented to outline the potential applications and solutions. These potential futuristic routes and their materials/technologies are considered/suggested for a 10-20 years time-frame.


  • Study of CORC Conductors With Respect to Individual Tape Properties

    by A. Torre, J. Pavan, B. Lacroix, C. Nguyen Thanh Dao, V. Corato, D.C. van der Laan

    CEA has been studying the advantages of a conductor based on an assembly of CORC cables in the high field zone of a hybrid Central Solenoid (CS) magnet for EU-DEMO. To this end, the detailed study of geometrical and electrical parameters of a CORC structure are studied in order to evaluate the cable’s electrical performance as well as to determine a number of important parameters (crossing points, contact surface etc…) as function of the cable structure. The paper first presents these geometrical and performance analyses. It will then try to introduce smeared models in order to reduce the cable’s performance to 1D tape scaling law using effective parameters. That reduction is of importance for use in thermohydraulic models. Finally, the paper will present the case study of a particular CORC conductor that is being procured and is foreseen to be tested in SULTAN in 2025. The paper will try to give some predictive estimate of the cable performance and identify some of the unknowns related to current redistribution and joint resistance.


  • Open Access

    Superconducting high-power cables and lines – Development status and technology roadmap

    by Mathias Noe, Teresa Puig, Danko C van der Laan, Robert Bach, Sasha Ishmael, Emelie Nilsson, Carsten Räch, Noriko Chikumoto, Arnaud Allais, Bai Song, et al.

    More than 35 years after the discovery of high-temperature superconductivity and more than 20 years after the first field-test installation of a high-temperature superconducting cable, superconducting cables and lines were developed successfully up to high voltage levels and several long-term field tests demonstrated a reliable operation. There are many different applications where superconducting cables and lines were developed in the past. The technology readiness level is very different among the applications. Whereas medium voltage cables for urban areas with a length of a km have been field tested for long times in several locations, high voltage long distance cables are still in the technology concept status. This contribution is structured in four main parts. A proper description of superconducting cables cannot be made without an overview on the present material R&D and the lessons learned from the many successful projects in the past. Presently, there are substantial activities to further develop superconducting cables for AC and high-current DC applications and they are summarized in the second part. Recently, two start-up companies were founded and their R&D is also included. The third part of this paper covers the experience with a reliable operation and the cooling aspects. These contributions focus on the experience from field test applications and on future developments in this area. Hydrogen as an energy carrier is getting more and more attractive and due to the high energy density liquid hydrogen is expected to be widely used at least in some applications. This would favour the combination with superconductors very much because of its temperature of 20 K at pool boiling conditions. The last part of this contribution summarizes present R&D activities for hybrid energy lines with chemical and electricity transport in one line.


  • Demonstration of current sharing around tape defects in a low-inductance CORC® wire solenoid generating a peak magnetic field of 4.6 T at 25 K

    by Jeremy D Weiss, Danko van der Laan, Chul H Kim, Reed Teyber, Kyle Radcliff, Virginia Phifer, Daniel S Davis, Yifei Zhang, Lance D Cooley, Sastry V Pamidi

    This manuscript presents the design, fabrication, and operation of high temperature superconducting conductor on round core (CORC®) wires utilizing variable critical current REBCO tapes that contain occasional dropouts of critical current (I c). Performance evaluations conducted at temperatures ranging from 25 K to 77 K demonstrated comparable superconducting characteristics between CORC® wires with and without intrinsic variations in I c within the REBCO tapes. This is a clear indication that the high level of current sharing between tapes in CORC® wires allows current to bypass local defects. A 70 mm bore, 4-layer CORC® solenoid in which 25 m of CORC® wire was wound into 81.5 turns, generated a peak magnetic field of 4.6 T at an I c of 4460 A at 25 K. The I c of the solenoid corresponds closely with the sum of the expected average tape I c, not its minimum I c driven by the tape dropouts. Experimental results confirmed stable dissipative operation at 4021 A (87% I c) continuous current with minimal power losses, highlighting the feasibility of manufacturing longer-length CORC® conductors from tapes with significant local dropouts for superconductor applications including fusion, accelerators, power transmission, and rotating machinery.


  • Open Access

    Impact of Contact Resistance on Current Distribution and Performance of Model CORC® Cables with Physical Defects

    by Virginia Phifer, Lance D Cooley, Danko C van der Laan, Jeremy D Weiss

    This work investigates current redistribution around defects in Conductor on Round Core (CORC®) cables. Special two tape CORC® cables were constructed containing just one tape per layer with a 100% Ic dropout in the outer conductor. Three different cable types were measured to investigate the impact of contact resistance between tapes, Rc, on current redistribution around local defects. An array of z-axis Hall sensors, which could be positioned at any location along the cable, monitored changes in the self-field due to current redistribution. A clear shift in Hall polarity occurs at the defect location, with Hall sensors producing a positive voltage upstream of the defect and a negative voltage downstream of the defect. As the current transfers around the defect, the “good” tape is overloaded, intiating a normal zone. In cables with high Rc, voltage taps reveal that the normal zone is confined to the “good” tape, while the “bad” tape remains superconducting. This normal zone can remain stable even at currents above Ic and can cause significant power dissipation, 590 mW at 60 A. As Rc decreases, facilitating better current sharing, the normal zone spreads to both tapes. These experiments have demonstrated that Rc can have a significant impact on power dissipation and that current sharing is essential for robust cable performance


  • Open Access

    Tape-in-tape-out (TITO): a new approach for in-situ contact resistance measurements in high temperature superconducting CORC® cables

    by Reed Teyber, Chet L Spencer, Jeremy Weiss, Danko van der Laan

    One of the ongoing development challenges with ReBCO high-temperature superconducting (HTS) cables is normal zone initiation and local heating, which is associated with over-critical current flowing through and around local performance reductions in individual tapes. Although inter-tape contact resistances are well-reported for individual tapes and HTS cables, these measurements are a challenge in CORC® cables as current percolates through much of the cable. In this work, developments in tape-in-tape-out (TITO) automated individual tape powering experiments are presented, and a simplified modeling approach for current percolation in CORC® cables is developed. An optimization is formulated to fit the model parameters to a large set of TITO experiments on a single cable, allowing the layer-dependent inter-tape contact resistance to be extracted. Measurements are presented and discussed for a straight CORC® cable and a cable bent to a 152 mm and 76 mm radius. The approach provides both quantitative insight and facilitates better understanding of current sharing phenomena in HTS cables.


  • Open Access

    Simulations of the fault current limiting operation of a long-length REBCO CORC® superconducting cable cooled by helium gas

    by Linh Ngoc Nguyen, Do Vo, Jeremy Weiss, Sven A Dönges, Francesco Grilli, Danko van der Laan, Sastry V Pamidi, Doan Ngoc Nguyen

    Conductor-on-round-core (CORC®) cables composed of rare-earth-barium-copper-oxide high-temperature superconducting (HTS) tapes are of great interest for power transmission applications due to their many advantages such as high power density, light weight, and low loss. Closed circulation loops of cryogenic helium gas can be used to cool HTS cables down to low temperatures to significantly improve their current-carrying capacity. Coupled circuit-electromagnetic-thermal finite element simulations implemented in the COMSOL Multiphysics package were developed, validated, and then used for simulating the fault current limiting (FCL) performance and the cooling processes of an 8-layer CORC® cable cooled with a flow of cryogenic helium gas. In the simulations, the temperature dependence of the electrical and thermal properties of all component materials is implemented for improved accuracy. To overcome computational challenges caused by the considerable difference in geometrical scales (i.e. few-µm-thick HTS layers versus 10 m-long HTS cable), the model is divided into two separate simulations. The first simulation is performed on the transverse cross-section of the cable to calculate the electric field, heating power and temperature rise in each component of a CORC® cable during FCL operation. The heating power calculated in the first simulation is transferred to the second model to simulate the cooling of a 10 m-long cable after the fault is cleared. The effect of the helium gas flow rate on the cooling process is also investigated to develop strategic approaches for optimizing cooling systems for HTS cables with FCL capability. The simulations indicated that a 40 ms fault with a voltage drop of 20 V m−1 along the cable can result in a temperature increase from 60 K to about 165 K inside the cable, and it takes about 500 s to cool the cable back to nearly 60 K with a flow of cold helium gas at a rate of 5 g s−1.


  • Fabrication and Test of C3a: A Six-Layer Subscale Canted $\cos \theta$ Dipole Magnet Using High-Temperature Superconducting corc Wires

    by Dmytro Abraimov, Diego Arbelaez, Lucas Brouwer, Helen Feng, Paolo Ferracin, William B. Ghiorso, Hugh C. Higley, Mariusz Juchno, Andy Lin, Thomas Lipton, et al.

    rebco coated conductors have a strong potential for high-field magnet applications. The rebco technology, however, is still in its infancy for accelerator magnet applications. As part of the U.S. Magnet Development Program, we developed a six-layer canted $\cos \theta$ dipole magnet, C3a, using corc wires developed by Advanced Conductor Technologies LLC. All the layers were wound using a semiautomated winding machine. Three layers of the magnet used corc wires containing the SuperPower “AP” rebco tapes and the remaining layers used the wires containing the “HM” tapes. At 77 K, both kinds of corc wires showed 5% to 10% degradation, after bending to a minimum bend radius of 30 or 35 mm, with respect to the self-field critical current measured before winding. At 4.2 K, the magnet reached 9.5 kA at a ramp rate of 9 A s$^{-1}$ and generated a dipole field of 1.4 T. The critical current of one layer degraded by 4% after a current transient up to 10.5 kA ramped in an averaged rate of 175 kA s$^{-1}$ or 20 T s$^{-1}$. We confirmed the HM corc wire can carry a higher current than the AP corc wire at 4.2 K. The test results of the C3a magnet showed that the fabrication and assembly procedure can be used for the upcoming full-scale C3 magnet.


  • Open Access

    Development and performance of high-temperature superconducting CORC® cables with CFD REBCO tapes

    by Haïfa Ben Saâd, Christian Lacroix, Delano Horn-Bourque, Emelie Nilsson, Jean-François Rouquette, Danko van der Laan, Jeremy Weiss, Kyle Radcliff, Frédéric Sirois

    Increasing the normal zone propagation velocity (NZPV) in superconducting cables based on rare earth barium copper oxide (REBCO) tapes is expected to cause a paradigm shift by enabling the development of faster and more reliable quench detection systems to mitigate the development of destructive hot spots. Furthermore, a higher NZPV is beneficial in terms of fault current limitation capabilities by accelerating the homogenization of the quench in superconducting power devices. One way envisioned to increase the NZPV of cables based on REBCO tapes is the current flow diverter (CFD) concept. A Conductor on Round Core (CORC®) cable made with CFD REBCO tapes, called CFD CORC® cable, and a CORC® cable made with regular REBCO tapes, were fabricated and tested. The critical current of the CFD and regular CORC® cables were obtained at temperatures ranging from 67 to 77 K in self-field. Measurements showed that the NZPV was increased by a factor of 4–4.5 in the case of the CFD CORC® cable. Furthermore, the results suggest that the NZPV depends only on the applied current, similar to what has been observed previously on single REBCO tapes. These results demonstrate the successful integration of CFD REBCO tapes in CORC® cables, without compromising their superconducting properties or their enhanced NZPV. The possibility of enhancing the NZPV of REBCO-based cables could facilitate quench detection, which remains an important issue in HTS magnet applications. This advancement also holds promise for the fault current limitation functionality of CORC® cables.