Jeremy David Weiss
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jeremy David Weiss has a total of 325 co-authors. Here are the top co-authors by number of shared publications:
- Danko van der Laan
Advanced Conductor Technologies LLC, Boulder, CO, USA
40 shared publications J. Jiang
Applied Superconductivity Center, National High Magnetic Field Laboratory, Florida State University, Tallahassee, FL 32310, USA
14 shared publications- David C. Larbalestier
Florida State University
13 shared publications E. E. Hellstrom
Applied Superconductivity Center, National High Magnetic Field Laboratory, Florida State University, 2031 East Paul Dirac Drive, Tallahassee, Florida 32310, USA
11 shared publications- Sanghan Lee
Department of Materials Science and Engineering Gwangju Institute of Science and Technology Gwangju Republic of Korea
11 shared publications - Xiaorong Wang
Lawrence Berkeley National Laboratory, Berkeley, CA, USA
10 shared publications
Latest Publications
- Open Access
- 14 August 2026
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 29 (8)
Fabrication and test of a 6-tesla-class high-temperature superconducting dipole magnet at 4.2 K
Superconducting magnets enable energy-frontier accelerators by generating strong magnetic fields to steer and focus the particles. Although high-temperature superconductors such as REBa 2 Cu 3 O x (, RE = rare earth) hold a strong potential for generating a higher magnetic field than Nb-Ti and Nb 3 Sn , the associated magnet and conductor technology for accelerator applications is still in its infancy. The U.S. Magnet Development Program is developing magnet technology in collaboration with industry. Here we report an experiment of making a dipole magnet called C3 using commercial high-temperature superconducting wires. The magnet, following a canted cos θ design, generated a dipole field of 5.99 T at 4.2 K in its clear aperture of 65 mm at 6.795 kA when a resistive voltage of 105 μ V appeared across one of the coils in the magnet. The stored energy was 53 kJ at the peak field. The magnet showed no degradation in the current-carrying capability at 4.2 K after the thermal cycle. We report on the detailed design, fabrication, and performance of the C3 magnet that can be of interest to potential users of this emerging technology. We also discuss issues and research needs to inform future magnet development. The experiment represented another step to addressing if the high-temperature superconducting accelerator magnet technology can increase the discovery capability of future particle accelerators.
- 14 August 2026
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 29 (8)
Open AccessFabrication and test of a 6-tesla-class high-temperature superconducting dipole magnet at 4.2 K
Superconducting magnets enable energy-frontier accelerators by generating strong magnetic fields to steer and focus the particles. Although high-temperature superconductors such as REBa 2 Cu 3 O x (, RE = rare earth) hold a strong potential for generating a higher magnetic field than Nb-Ti and Nb 3 Sn , the associated magnet and conductor technology for accelerator applications is still in its infancy. The U.S. Magnet Development Program is developing magnet technology in collaboration with industry. Here we report an experiment of making a dipole magnet called C3 using commercial high-temperature superconducting wires. The magnet, following a canted cos θ design, generated a dipole field of 5.99 T at 4.2 K in its clear aperture of 65 mm at 6.795 kA when a resistive voltage of 105 μ V appeared across one of the coils in the magnet. The stored energy was 53 kJ at the peak field. The magnet showed no degradation in the current-carrying capability at 4.2 K after the thermal cycle. We report on the detailed design, fabrication, and performance of the C3 magnet that can be of interest to potential users of this emerging technology. We also discuss issues and research needs to inform future magnet development. The experiment represented another step to addressing if the high-temperature superconducting accelerator magnet technology can increase the discovery capability of future particle accelerators.
- 1 August 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (8) , 085007
Demonstration of current sharing around tape defects in a low-inductance CORC® wire solenoid generating a peak magnetic field of 4.6 T at 25 K
This manuscript presents the design, fabrication, and operation of high temperature superconducting conductor on round core (CORC®) wires utilizing variable critical current REBCO tapes that contain occasional dropouts of critical current (I c). Performance evaluations conducted at temperatures ranging from 25 K to 77 K demonstrated comparable superconducting characteristics between CORC® wires with and without intrinsic variations in I c within the REBCO tapes. This is a clear indication that the high level of current sharing between tapes in CORC® wires allows current to bypass local defects. A 70 mm bore, 4-layer CORC® solenoid in which 25 m of CORC® wire was wound into 81.5 turns, generated a peak magnetic field of 4.6 T at an I c of 4460 A at 25 K. The I c of the solenoid corresponds closely with the sum of the expected average tape I c, not its minimum I c driven by the tape dropouts. Experimental results confirmed stable dissipative operation at 4021 A (87% I c) continuous current with minimal power losses, highlighting the feasibility of manufacturing longer-length CORC® conductors from tapes with significant local dropouts for superconductor applications including fusion, accelerators, power transmission, and rotating machinery.
- 1 August 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (8) , 085007
Demonstration of current sharing around tape defects in a low-inductance CORC® wire solenoid generating a peak magnetic field of 4.6 T at 25 K
This manuscript presents the design, fabrication, and operation of high temperature superconducting conductor on round core (CORC®) wires utilizing variable critical current REBCO tapes that contain occasional dropouts of critical current (I c). Performance evaluations conducted at temperatures ranging from 25 K to 77 K demonstrated comparable superconducting characteristics between CORC® wires with and without intrinsic variations in I c within the REBCO tapes. This is a clear indication that the high level of current sharing between tapes in CORC® wires allows current to bypass local defects. A 70 mm bore, 4-layer CORC® solenoid in which 25 m of CORC® wire was wound into 81.5 turns, generated a peak magnetic field of 4.6 T at an I c of 4460 A at 25 K. The I c of the solenoid corresponds closely with the sum of the expected average tape I c, not its minimum I c driven by the tape dropouts. Experimental results confirmed stable dissipative operation at 4021 A (87% I c) continuous current with minimal power losses, highlighting the feasibility of manufacturing longer-length CORC® conductors from tapes with significant local dropouts for superconductor applications including fusion, accelerators, power transmission, and rotating machinery.
- Open Access
- 1 July 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (7) , 075023
Tape-in-tape-out (TITO): a new approach for in-situ contact resistance measurements in high temperature superconducting CORC® cables
One of the ongoing development challenges with ReBCO high-temperature superconducting (HTS) cables is normal zone initiation and local heating, which is associated with over-critical current flowing through and around local performance reductions in individual tapes. Although inter-tape contact resistances are well-reported for individual tapes and HTS cables, these measurements are a challenge in CORC® cables as current percolates through much of the cable. In this work, developments in tape-in-tape-out (TITO) automated individual tape powering experiments are presented, and a simplified modeling approach for current percolation in CORC® cables is developed. An optimization is formulated to fit the model parameters to a large set of TITO experiments on a single cable, allowing the layer-dependent inter-tape contact resistance to be extracted. Measurements are presented and discussed for a straight CORC® cable and a cable bent to a 152 mm and 76 mm radius. The approach provides both quantitative insight and facilitates better understanding of current sharing phenomena in HTS cables.
- 1 July 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (7) , 075023
Open AccessTape-in-tape-out (TITO): a new approach for in-situ contact resistance measurements in high temperature superconducting CORC® cables
One of the ongoing development challenges with ReBCO high-temperature superconducting (HTS) cables is normal zone initiation and local heating, which is associated with over-critical current flowing through and around local performance reductions in individual tapes. Although inter-tape contact resistances are well-reported for individual tapes and HTS cables, these measurements are a challenge in CORC® cables as current percolates through much of the cable. In this work, developments in tape-in-tape-out (TITO) automated individual tape powering experiments are presented, and a simplified modeling approach for current percolation in CORC® cables is developed. An optimization is formulated to fit the model parameters to a large set of TITO experiments on a single cable, allowing the layer-dependent inter-tape contact resistance to be extracted. Measurements are presented and discussed for a straight CORC® cable and a cable bent to a 152 mm and 76 mm radius. The approach provides both quantitative insight and facilitates better understanding of current sharing phenomena in HTS cables.
- Open Access
- 1 June 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (6) , 065020
Simulations of the fault current limiting operation of a long-length REBCO CORC® superconducting cable cooled by helium gas
Conductor-on-round-core (CORC®) cables composed of rare-earth-barium-copper-oxide high-temperature superconducting (HTS) tapes are of great interest for power transmission applications due to their many advantages such as high power density, light weight, and low loss. Closed circulation loops of cryogenic helium gas can be used to cool HTS cables down to low temperatures to significantly improve their current-carrying capacity. Coupled circuit-electromagnetic-thermal finite element simulations implemented in the COMSOL Multiphysics package were developed, validated, and then used for simulating the fault current limiting (FCL) performance and the cooling processes of an 8-layer CORC® cable cooled with a flow of cryogenic helium gas. In the simulations, the temperature dependence of the electrical and thermal properties of all component materials is implemented for improved accuracy. To overcome computational challenges caused by the considerable difference in geometrical scales (i.e. few-µm-thick HTS layers versus 10 m-long HTS cable), the model is divided into two separate simulations. The first simulation is performed on the transverse cross-section of the cable to calculate the electric field, heating power and temperature rise in each component of a CORC® cable during FCL operation. The heating power calculated in the first simulation is transferred to the second model to simulate the cooling of a 10 m-long cable after the fault is cleared. The effect of the helium gas flow rate on the cooling process is also investigated to develop strategic approaches for optimizing cooling systems for HTS cables with FCL capability. The simulations indicated that a 40 ms fault with a voltage drop of 20 V m−1 along the cable can result in a temperature increase from 60 K to about 165 K inside the cable, and it takes about 500 s to cool the cable back to nearly 60 K with a flow of cold helium gas at a rate of 5 g s−1.
- 1 June 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (6) , 065020
Open AccessSimulations of the fault current limiting operation of a long-length REBCO CORC® superconducting cable cooled by helium gas
Conductor-on-round-core (CORC®) cables composed of rare-earth-barium-copper-oxide high-temperature superconducting (HTS) tapes are of great interest for power transmission applications due to their many advantages such as high power density, light weight, and low loss. Closed circulation loops of cryogenic helium gas can be used to cool HTS cables down to low temperatures to significantly improve their current-carrying capacity. Coupled circuit-electromagnetic-thermal finite element simulations implemented in the COMSOL Multiphysics package were developed, validated, and then used for simulating the fault current limiting (FCL) performance and the cooling processes of an 8-layer CORC® cable cooled with a flow of cryogenic helium gas. In the simulations, the temperature dependence of the electrical and thermal properties of all component materials is implemented for improved accuracy. To overcome computational challenges caused by the considerable difference in geometrical scales (i.e. few-µm-thick HTS layers versus 10 m-long HTS cable), the model is divided into two separate simulations. The first simulation is performed on the transverse cross-section of the cable to calculate the electric field, heating power and temperature rise in each component of a CORC® cable during FCL operation. The heating power calculated in the first simulation is transferred to the second model to simulate the cooling of a 10 m-long cable after the fault is cleared. The effect of the helium gas flow rate on the cooling process is also investigated to develop strategic approaches for optimizing cooling systems for HTS cables with FCL capability. The simulations indicated that a 40 ms fault with a voltage drop of 20 V m−1 along the cable can result in a temperature increase from 60 K to about 165 K inside the cable, and it takes about 500 s to cool the cable back to nearly 60 K with a flow of cold helium gas at a rate of 5 g s−1.
- 28 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (6) , 1-15
Fabrication and Test of C3a: A Six-Layer Subscale Canted $\cos \theta$ Dipole Magnet Using High-Temperature Superconducting corc Wiresrebco coated conductors have a strong potential for high-field magnet applications. The rebco technology, however, is still in its infancy for accelerator magnet applications. As part of the U.S. Magnet Development Program, we developed a six-layer canted $\cos \theta$ dipole magnet, C3a, using corc wires developed by Advanced Conductor Technologies LLC. All the layers were wound using a semiautomated winding machine. Three layers of the magnet used corc wires containing the SuperPower “AP” rebco tapes and the remaining layers used the wires containing the “HM” tapes. At 77 K, both kinds of corc wires showed 5% to 10% degradation, after bending to a minimum bend radius of 30 or 35 mm, with respect to the self-field critical current measured before winding. At 4.2 K, the magnet reached 9.5 kA at a ramp rate of 9 A s$^{-1}$ and generated a dipole field of 1.4 T. The critical current of one layer degraded by 4% after a current transient up to 10.5 kA ramped in an averaged rate of 175 kA s$^{-1}$ or 20 T s$^{-1}$. We confirmed the HM corc wire can carry a higher current than the AP corc wire at 4.2 K. The test results of the C3a magnet showed that the fabrication and assembly procedure can be used for the upcoming full-scale C3 magnet.
- 28 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (6) , 1-15
Fabrication and Test of C3a: A Six-Layer Subscale Canted $\cos \theta$ Dipole Magnet Using High-Temperature Superconducting corc Wiresrebco coated conductors have a strong potential for high-field magnet applications. The rebco technology, however, is still in its infancy for accelerator magnet applications. As part of the U.S. Magnet Development Program, we developed a six-layer canted $\cos \theta$ dipole magnet, C3a, using corc wires developed by Advanced Conductor Technologies LLC. All the layers were wound using a semiautomated winding machine. Three layers of the magnet used corc wires containing the SuperPower “AP” rebco tapes and the remaining layers used the wires containing the “HM” tapes. At 77 K, both kinds of corc wires showed 5% to 10% degradation, after bending to a minimum bend radius of 30 or 35 mm, with respect to the self-field critical current measured before winding. At 4.2 K, the magnet reached 9.5 kA at a ramp rate of 9 A s$^{-1}$ and generated a dipole field of 1.4 T. The critical current of one layer degraded by 4% after a current transient up to 10.5 kA ramped in an averaged rate of 175 kA s$^{-1}$ or 20 T s$^{-1}$. We confirmed the HM corc wire can carry a higher current than the AP corc wire at 4.2 K. The test results of the C3a magnet showed that the fabrication and assembly procedure can be used for the upcoming full-scale C3 magnet.
- Open Access
- 11 February 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (3) , 035007
Development and performance of high-temperature superconducting CORC® cables with CFD REBCO tapes
Increasing the normal zone propagation velocity (NZPV) in superconducting cables based on rare earth barium copper oxide (REBCO) tapes is expected to cause a paradigm shift by enabling the development of faster and more reliable quench detection systems to mitigate the development of destructive hot spots. Furthermore, a higher NZPV is beneficial in terms of fault current limitation capabilities by accelerating the homogenization of the quench in superconducting power devices. One way envisioned to increase the NZPV of cables based on REBCO tapes is the current flow diverter (CFD) concept. A Conductor on Round Core (CORC®) cable made with CFD REBCO tapes, called CFD CORC® cable, and a CORC® cable made with regular REBCO tapes, were fabricated and tested. The critical current of the CFD and regular CORC® cables were obtained at temperatures ranging from 67 to 77 K in self-field. Measurements showed that the NZPV was increased by a factor of 4–4.5 in the case of the CFD CORC® cable. Furthermore, the results suggest that the NZPV depends only on the applied current, similar to what has been observed previously on single REBCO tapes. These results demonstrate the successful integration of CFD REBCO tapes in CORC® cables, without compromising their superconducting properties or their enhanced NZPV. The possibility of enhancing the NZPV of REBCO-based cables could facilitate quench detection, which remains an important issue in HTS magnet applications. This advancement also holds promise for the fault current limitation functionality of CORC® cables.
- 11 February 2025
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 38 (3) , 035007
Open AccessDevelopment and performance of high-temperature superconducting CORC® cables with CFD REBCO tapes
Increasing the normal zone propagation velocity (NZPV) in superconducting cables based on rare earth barium copper oxide (REBCO) tapes is expected to cause a paradigm shift by enabling the development of faster and more reliable quench detection systems to mitigate the development of destructive hot spots. Furthermore, a higher NZPV is beneficial in terms of fault current limitation capabilities by accelerating the homogenization of the quench in superconducting power devices. One way envisioned to increase the NZPV of cables based on REBCO tapes is the current flow diverter (CFD) concept. A Conductor on Round Core (CORC®) cable made with CFD REBCO tapes, called CFD CORC® cable, and a CORC® cable made with regular REBCO tapes, were fabricated and tested. The critical current of the CFD and regular CORC® cables were obtained at temperatures ranging from 67 to 77 K in self-field. Measurements showed that the NZPV was increased by a factor of 4–4.5 in the case of the CFD CORC® cable. Furthermore, the results suggest that the NZPV depends only on the applied current, similar to what has been observed previously on single REBCO tapes. These results demonstrate the successful integration of CFD REBCO tapes in CORC® cables, without compromising their superconducting properties or their enhanced NZPV. The possibility of enhancing the NZPV of REBCO-based cables could facilitate quench detection, which remains an important issue in HTS magnet applications. This advancement also holds promise for the fault current limitation functionality of CORC® cables.
- 30 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Twisting & Bending Performance of a Subscale CORC Cable-in-Conduit-Conductor for Fusion and Detector Magnet Applications
Future magnetic confinement fusion machines and detector magnets will likely utilize high temperature superconducting (HTS) wire and/or tapes, configured in a Cable-in-Conduit-Conductor (CICC) to generate magnetic fields at temperatures above 4.2 K. As such, these CICCs will need to be twisted & bent to meet the design criteria for any given machine. We investigated the critical current (Ic) degradation of a subscale 6-around-1 CICC using Conductor-on-Round-Core® (CORC®) wires after ever increasing deformation. A CORC® wire was inserted into one of six outer openings of an extruded aluminum conduit to form a sub-scale CICC, after which the CICC was twisted to ∼25 cm pitch and the whole assembly was then sequentially bent to nominal radii of ∼50 cm, ∼35 cm, and ∼25 cm. The Ic values at 77 K and self-field when straight and after each deformation step was measured. The CORC® wire Ic was robust to this type of “twisting + bending” deformation, with an overall degradation of ∼10% with respect to the straight, non-twisted wire. We also describe a CICC twisting process that potentially allows twisting of continuous-length CICCs after the CORC® wires are inserted. This method can lead to a scalable fabrication process of long-length CORC® CICCs that are required for manufacture of high-field fusion magnets and detector magnets for high-energy physics research.
- 30 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Twisting & Bending Performance of a Subscale CORC Cable-in-Conduit-Conductor for Fusion and Detector Magnet Applications
Future magnetic confinement fusion machines and detector magnets will likely utilize high temperature superconducting (HTS) wire and/or tapes, configured in a Cable-in-Conduit-Conductor (CICC) to generate magnetic fields at temperatures above 4.2 K. As such, these CICCs will need to be twisted & bent to meet the design criteria for any given machine. We investigated the critical current (Ic) degradation of a subscale 6-around-1 CICC using Conductor-on-Round-Core® (CORC®) wires after ever increasing deformation. A CORC® wire was inserted into one of six outer openings of an extruded aluminum conduit to form a sub-scale CICC, after which the CICC was twisted to ∼25 cm pitch and the whole assembly was then sequentially bent to nominal radii of ∼50 cm, ∼35 cm, and ∼25 cm. The Ic values at 77 K and self-field when straight and after each deformation step was measured. The CORC® wire Ic was robust to this type of “twisting + bending” deformation, with an overall degradation of ∼10% with respect to the straight, non-twisted wire. We also describe a CICC twisting process that potentially allows twisting of continuous-length CICCs after the CORC® wires are inserted. This method can lead to a scalable fabrication process of long-length CORC® CICCs that are required for manufacture of high-field fusion magnets and detector magnets for high-energy physics research.
- 27 September 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (11) , 115007
CORC® wires allowing bending to 20 mm radius with 97.5% retention in critical current and having an engineering current density of 530 A mm−2 at 20 T
Low-inductance, high-field insert solenoid magnets and 20 T dipole magnets for particle accelerators require flexible cables, wound from high-temperature superconductors (HTS) such as RE-Ba2Cu3O7− δ (REBCO) coated conductors, that allow bending to a 20 mm radius without significant degradation in performance. They require an operating current of at least 5 kA and a high engineering current density (J e) exceeding 500 A mm−2 at 20 T. HTS cable technologies that target such demanding magnet applications so far have not been able to meet the combination of these requirements. Here we present the development of the next generation of Conductor on Round Core (CORC®) wires that are produced with an optimized manufacturing process that improves their bending flexibility by factor of more than 2 compared to previous generation CORC® wires. CORC® wires now allow for a bending radius of 20 mm with only 2%–3% performance degradation. They allow bending to a radius of 15 mm with a performance retention of 83.5%. The performance of 30-tape CORC® wires wound from 2 mm wide REBCO tapes from SuperPower Inc, SuperOx and shanghai superconductor technologies was measured at magnetic fields up to 12 T. The overall performance at high magnetic fields of the next generation of CORC® wires improved by a factor of 1.5–1.8, depending on the REBCO tape manufacturer. CORC® wires wound from production REBCO tapes achieved a new record J e of 751 A mm−2 at a current of 8.3 kA at 12 T, and a J e of 530 A mm−2 at a current of 5.8 kA when extrapolated to 20 T. The next generation of CORC® wires present the first HTS cable technology that simultaneously meet the requirements on bending flexibility, engineering current density and critical current at 20 T for use in low-inductance, high-field particle accelerator magnets. They now enable a more expedited development of prototype low-inductance solenoid magnets that target fields exceeding 25 T and of accelerator magnets that generate a dipole field exceeding 20 T.
- 27 September 2024
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 37 (11) , 115007
CORC® wires allowing bending to 20 mm radius with 97.5% retention in critical current and having an engineering current density of 530 A mm−2 at 20 T
Low-inductance, high-field insert solenoid magnets and 20 T dipole magnets for particle accelerators require flexible cables, wound from high-temperature superconductors (HTS) such as RE-Ba2Cu3O7− δ (REBCO) coated conductors, that allow bending to a 20 mm radius without significant degradation in performance. They require an operating current of at least 5 kA and a high engineering current density (J e) exceeding 500 A mm−2 at 20 T. HTS cable technologies that target such demanding magnet applications so far have not been able to meet the combination of these requirements. Here we present the development of the next generation of Conductor on Round Core (CORC®) wires that are produced with an optimized manufacturing process that improves their bending flexibility by factor of more than 2 compared to previous generation CORC® wires. CORC® wires now allow for a bending radius of 20 mm with only 2%–3% performance degradation. They allow bending to a radius of 15 mm with a performance retention of 83.5%. The performance of 30-tape CORC® wires wound from 2 mm wide REBCO tapes from SuperPower Inc, SuperOx and shanghai superconductor technologies was measured at magnetic fields up to 12 T. The overall performance at high magnetic fields of the next generation of CORC® wires improved by a factor of 1.5–1.8, depending on the REBCO tape manufacturer. CORC® wires wound from production REBCO tapes achieved a new record J e of 751 A mm−2 at a current of 8.3 kA at 12 T, and a J e of 530 A mm−2 at a current of 5.8 kA when extrapolated to 20 T. The next generation of CORC® wires present the first HTS cable technology that simultaneously meet the requirements on bending flexibility, engineering current density and critical current at 20 T for use in low-inductance, high-field particle accelerator magnets. They now enable a more expedited development of prototype low-inductance solenoid magnets that target fields exceeding 25 T and of accelerator magnets that generate a dipole field exceeding 20 T.
- 9 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-5
Calculation and Measurement of Transport AC Loss of ReBCO CORC Cables for Electric Aircraft
This paper investigates transport AC loss in CORC cables for the ground-based demonstrator ASCEND at Airbus, which studies the feasibility of a superconducting powertrain for electric aircraft. The demonstrator includes a three-phase AC link consisting of three parallel cables operating at 500 Hz and 2350 A peak current. The transport AC loss of the three-phase cable is estimated using a 2D model assuming equal current in all tapes. The model predicts an AC loss of 40 W at 77.5 K and 0.4 W at 65 K. A second model is proposed, which computes the current distribution between the tapes in a single cable using mutual inductance matrices for helical tape conductors. This model predicts that, at 500 Hz, the outer two layers of a CORC cable carry a disproportionate fraction of the current. This will lead to additional AC loss if the critical current in the outer layers is exceeded. AC transport loss was measured on single CORC cables. Both models significantly underestimate the measured loss. Also, a frequency-dependent quench current below the DC critical current was observed at 48 Hz and 96 Hz.
- 9 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-5
Calculation and Measurement of Transport AC Loss of ReBCO CORC Cables for Electric Aircraft
This paper investigates transport AC loss in CORC cables for the ground-based demonstrator ASCEND at Airbus, which studies the feasibility of a superconducting powertrain for electric aircraft. The demonstrator includes a three-phase AC link consisting of three parallel cables operating at 500 Hz and 2350 A peak current. The transport AC loss of the three-phase cable is estimated using a 2D model assuming equal current in all tapes. The model predicts an AC loss of 40 W at 77.5 K and 0.4 W at 65 K. A second model is proposed, which computes the current distribution between the tapes in a single cable using mutual inductance matrices for helical tape conductors. This model predicts that, at 500 Hz, the outer two layers of a CORC cable carry a disproportionate fraction of the current. This will lead to additional AC loss if the critical current in the outer layers is exceeded. AC transport loss was measured on single CORC cables. Both models significantly underestimate the measured loss. Also, a frequency-dependent quench current below the DC critical current was observed at 48 Hz and 96 Hz.
- 25 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-4
Performance of the 500 kW Superconducting DC and AC Links of the ASCEND Demonstrator at Airbus
In the quest for climate neutrality in the aviation industry by 2050, technology development is one of the main pathways for Airbus. Owing to their high efficiency and current density, use of superconducting DC and AC distribution lines are a potential enabler for fully electric propulsion in a longer range aircraft, in particular in the scenario where liquid hydrogen provides a cold source on board of the aircraft. The ground-based Advanced Superconducting and Cryogenic Experimental power traiN Demonstrator (ASCEND) at Airbus intends to demonstrate the potential and feasibility of a cryogenic and superconducting powertrain as a breakthrough electric propulsion solution on future electric aircraft. A direct current distribution network is used in a generic propulsion system to transfer 500 kW power from the DC supply to an electrical converter, which transforms the energy into an alternating voltage/current to drive the superconducting motor. A relatively low voltage level of 300 V, and a current of 1700 A, is chosen to optimize the safety and installation in a future aircraft by operating at relatively low voltage. The DC link consists of a 10 m long two-pole superconducting Conductor on Round Core (CORC) cable, and demountable current leads, that transfer the power from the room temperature environment to the cryogenically cooled motor control unit. Downstream of this unit a 3-phase AC link operating at 500 Hz delivers power to a superconducting motor. Both the AC and DC links are cooled with a flow of subcooled LN 2 . The components of the DC and AC links have been designed, manufactured and recently integrated into the ASCEND test bench in Ottobrunn, Germany. We present the powering of the DC link up to nominal current, as well as commissioning and integration experience.
- 25 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (3) , 1-4
Performance of the 500 kW Superconducting DC and AC Links of the ASCEND Demonstrator at Airbus
In the quest for climate neutrality in the aviation industry by 2050, technology development is one of the main pathways for Airbus. Owing to their high efficiency and current density, use of superconducting DC and AC distribution lines are a potential enabler for fully electric propulsion in a longer range aircraft, in particular in the scenario where liquid hydrogen provides a cold source on board of the aircraft. The ground-based Advanced Superconducting and Cryogenic Experimental power traiN Demonstrator (ASCEND) at Airbus intends to demonstrate the potential and feasibility of a cryogenic and superconducting powertrain as a breakthrough electric propulsion solution on future electric aircraft. A direct current distribution network is used in a generic propulsion system to transfer 500 kW power from the DC supply to an electrical converter, which transforms the energy into an alternating voltage/current to drive the superconducting motor. A relatively low voltage level of 300 V, and a current of 1700 A, is chosen to optimize the safety and installation in a future aircraft by operating at relatively low voltage. The DC link consists of a 10 m long two-pole superconducting Conductor on Round Core (CORC) cable, and demountable current leads, that transfer the power from the room temperature environment to the cryogenically cooled motor control unit. Downstream of this unit a 3-phase AC link operating at 500 Hz delivers power to a superconducting motor. Both the AC and DC links are cooled with a flow of subcooled LN 2 . The components of the DC and AC links have been designed, manufactured and recently integrated into the ASCEND test bench in Ottobrunn, Germany. We present the powering of the DC link up to nominal current, as well as commissioning and integration experience.