MHMaría Florencia Hernández

María Florencia Hernández

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


María Florencia Hernández has a total of 20 co-authors. Here are the top co-authors by number of shared publications:

  • A Violini

    Departamento de química Facultad de Ciencias Exactas Universidad Nacional de La Plata 47 y 115 La Plata 1900 Buenos Aires Argentina

    1 shared publication
  • Anabella Mocciaro

    Centro de Tecnología de Recursos Minerales y Cerámica (CIC-CONICET La Plata-UNLP), Cno. Centenario y 506, Manuel Bernardo Gonnet 1897, Argentina

    1 shared publication
  • Diego Richard

    Centro de Tecnología de Recursos Minerales y Cerámica (CIC-CONICET La Plata-UNLP), Cno. Centenario y 506, Manuel Bernardo Gonnet 1897, Argentina

    1 shared publication
  • Fernando Booth

    Universidad Nacional Del Chaco Austral - Comandante Fernández- Presidencia Roque Sáenz Peña, Chaco, Argentina

    1 shared publication
  • G Suárez

    Departamento de química Facultad de Ciencias Exactas Universidad Nacional de La Plata 47 y 115 La Plata 1900 Buenos Aires Argentina

    1 shared publication
  • G. Suarez

    CETMIC Centro de Tecnología de Recursos Minerales y Cerámica (CIC-CONICET La Plata), Buenos Aires, Argentina

    1 shared publication

Latest Publications

  • Open Access

    Experimental and Theoretical Study of the Thermal Shock Behavior of Insulating Refractory Materials

    by Anabella Mocciaro, Ricardo Anaya, María Florencia Hernández, Diego Richard, Nicolás Maximiliano Rendtorff

    This study investigates the thermal shock behavior of three Al2O3-SiO2 commercial insulating refractory materials (JM23, JM26, and JM28) used in high-temperature industries (>1000 °C). Thermal shock resistance was evaluated through experimental tests and compared with theoretical parameters (R, R⁗, Rst) based on thermoelastic and thermomechanical models. The tests revealed that JM23 did not withstand thermal shock due to its fragility when in contact with water at room temperature, resulting in its immediate collapse. In contrast, JM26 and JM28 maintained their mechanical strength after several thermal shock cycles, although JM28 experienced a more significant decrease in compressive strength. The mechanical behavior under compression changed from semi-fragile to apparently plastic after severe heat treatments. Porosity analysis showed that JM26 had a lower pore size distribution, which contributed to its better thermal shock performance. Theoretical parameters were calculated, confirming that JM26 exhibited the highest resistance to thermal shock. These findings suggest that controlled porosity and microstructure are key factors in improving the thermal performance and durability of insulating refractory materials in high-temperature applications.


  • Open Access

    Partially stabilized zirconia (3Y-ZrO2) aluminum borate (Al18B4O33) needles composite materials by direct sintering

    by Juan M. Martinez, María F. Hernández, Fernando Booth, Paula V. Lopez, Gustavo Suarez, María S. Conconi, Nicolás M. Rendtorff

    Novel 1:1 Yttria partially stabilized zirconia (PSZ) - aluminum borate (AB: Al11B4O33) ceramic composites were prepared and characterized by a simple direct sintering process of PSZ-mixtures. Sintering was performed below 1300°C to minimize the decomposition of borate. Phases were corroborated by XRD. SEM permitted to characterize the microstructure as interlocking needles of - rounded by PSZ grains. Porous microstructure configuration was achieved by the proposed processing route. Porosity was within 30% for samples thermally treated at 1200 and 1300°C. Mechanical behavior was evaluated by diametral compression. A fragile behavior was observed. Both strength and apparent Young modulus were evaluated being ≈30 MPa and ≈3 GPa respectively; values four times higher than the corresponding alumina-AB composite. This is more important when firing at higher temperature. The density of the obtained composites coupled with the mechanical behavior are the main characteristics of this novel composite with potential structural, insulating and filtering applications.


  • Open Access

    Dense alumina-mullite composite ceramics from alumina and spodumene-albite feldspar binary mixtures: Processing and properties

    by M Hernández, P López, A Violini, G Suárez, M Conconi, N Rendtorff

    A processing strategy for obtaining alumina-spodumene ceramics from fine commercial powders is presented. In this work, a spodumene addition to calcined alumina powder was performed and their proportion was explored between 15 and 45 wt%. The industrial spodumene presented secondary phases, mainly albite and quartz. Mechanical properties were evaluated. Although they were lower than those of sintered alumina, based on the achieved values an adequate behavior in structural applications can be assumed, especially taking into account that the better mechanical behavior was coupled with the lower thermal expansion. Relatively low thermal expansion( ? 5 x 10-1?C-1) behaviors were observed in one of the developed materials. Noncrystalline phases containing lithium were detected. We assume that all the lithium oxide incorporated through the spodumene is in the glassy phase after the sintering of the materials. This difference in lithium concentration in the composition of the resulting glass affected the thermal expansion of the developed materials. Particularly with low lithium content (30 wt% of additive) the material performance was enhanced. This, together with the mechanical behavior, encourages structural applications with high thermomechanical solicitations. With the information gathered, a wide range of materials with specific properties can be obtained by modulating the spodumene-alumina proportion only.