Bharat B. Panigrahi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Bharat B. Panigrahi has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Rahul B. Mane
Department of Materials Science and Metallurgical Engineering, Indian Institute of Technology Hyderabad, Sangareddy, Telangana 502285, India
2 shared publicationsBapurao M. Rahul
Department of Materials Science and Metallurgical Engineering Indian Institute of Technology Hyderabad, Kandi Sangareddy 502285 Telangana India
1 shared publication- Chitta Ranjan Das
Indira Gandhi Centre for Atomic Research
1 shared publication Govind Ummethala
Department of Materials Science and Metallurgical Engineering, Indian Institute of Technology Hyderabad, Sangareddy, Telangana 502285, India
1 shared publication- Joydip Joardar
International Advanced Research Centre for Powder Metallurgy and New Materials, Hyderabad, India, India
1 shared publication Kirtiratan Godbole
Department of Materials Science and Metallurgical Engineering, Indian Institute of Technology Hyderabad, Kandi, India
1 shared publication
Latest Publications
- 1 July 2020
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 51 (7) , 3377-3383
Toughening of AISI 410 Stainless Steel Through Quenching and Partitioning and Effect of Prolonged Aging on Microstructure and Mechanical Properties
- 1 July 2020
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 51 (7) , 3377-3383
Toughening of AISI 410 Stainless Steel Through Quenching and Partitioning and Effect of Prolonged Aging on Microstructure and Mechanical Properties
- 14 February 2019
- Published by Springer Nature in Journal of Materials Research
- Vol. 34 (5) , 777-786
Nearly full-density pressureless sintering of AlCoCrFeNi-based high-entropy alloy powders
- 14 February 2019
- Published by Springer Nature in Journal of Materials Research
- Vol. 34 (5) , 777-786
Nearly full-density pressureless sintering of AlCoCrFeNi-based high-entropy alloy powders
- 17 July 2018
- Published by Springer Nature in Journal of Materials Research
- Vol. 33 (19) , 3321-3329
Sintering mechanisms of mechanically alloyed CoCrFeNi high-entropy alloy powders
- 17 July 2018
- Published by Springer Nature in Journal of Materials Research
- Vol. 33 (19) , 3321-3329
Sintering mechanisms of mechanically alloyed CoCrFeNi high-entropy alloy powders
- 15 February 2018
- Published by SAGE Publications in Powder Metallurgy
- Vol. 61 (2) , 131-138
Sintering mechanism of CoCrFeMnNi high-entropy alloy powders
High-entropy alloys (HEAs) have emerged as a new alloy system, with many attractive properties. Among the fabrication routes, mechanical alloying followed by sintering, have been widely used. However, sintering mechanisms of HEA powders have not yet been fully understood. This work attempts to understand the sintering kinetics of CoCrFeNiMn HEA powders. A comparative study has been done on CoCrFeNiMn alloy powders on as-milled and annealed conditions, which revealed different sintering behaviours. Decreasing densification rates with increasing activation energies were observed through dilatometry after the annealing treatment. Combined diffusion coefficients and activation energies analysed through the sintering models indicate that during sintering of the as-milled powder, mass transport occurred through several modes. On the other hand, the annealed CoCrFeNiMn alloy powder (which was nearly single phase) clearly reveals volume diffusion as the controlling mechanism during sintering. It was characterised with large activation energy. Special theme block on high entropy alloys, guest edited by Paula Alvaredo Olmos, Universidad Carlos III de Madrid, Spain, and Sheng Guo, Chalmers University, Gothenburg, Sweden.
- 15 February 2018
- Published by SAGE Publications in Powder Metallurgy
- Vol. 61 (2) , 131-138
Sintering mechanism of CoCrFeMnNi high-entropy alloy powders
High-entropy alloys (HEAs) have emerged as a new alloy system, with many attractive properties. Among the fabrication routes, mechanical alloying followed by sintering, have been widely used. However, sintering mechanisms of HEA powders have not yet been fully understood. This work attempts to understand the sintering kinetics of CoCrFeNiMn HEA powders. A comparative study has been done on CoCrFeNiMn alloy powders on as-milled and annealed conditions, which revealed different sintering behaviours. Decreasing densification rates with increasing activation energies were observed through dilatometry after the annealing treatment. Combined diffusion coefficients and activation energies analysed through the sintering models indicate that during sintering of the as-milled powder, mass transport occurred through several modes. On the other hand, the annealed CoCrFeNiMn alloy powder (which was nearly single phase) clearly reveals volume diffusion as the controlling mechanism during sintering. It was characterised with large activation energy. Special theme block on high entropy alloys, guest edited by Paula Alvaredo Olmos, Universidad Carlos III de Madrid, Spain, and Sheng Guo, Chalmers University, Gothenburg, Sweden.
- 7 November 2016
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 14 (1) , 63-67
Nonisothermal sintering of Cr2AlC powder
This work studies the sintering behavior of ultrafine powder of Cr2AlC compound during nonisothermal heating using a dilatometer. Sample exhibits relatively slower densification under pressureless condition where relative density increased from about 61% (green compact) to about 73% during heating up to 1350°C. Axial shrinkage data were analyzed through the volume diffusion and grain boundary diffusion‐based sintering models. Estimated activation energy of sintering (352kJ/mol) for volume diffusion mechanism, was found to be closely matching with the reported activation energy of chromium diffusivity, indicating volume diffusion as a controlling mechanism and chromium as a major diffuser in Cr2AlC.
- 7 November 2016
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 14 (1) , 63-67
Nonisothermal sintering of Cr2AlC powder
This work studies the sintering behavior of ultrafine powder of Cr2AlC compound during nonisothermal heating using a dilatometer. Sample exhibits relatively slower densification under pressureless condition where relative density increased from about 61% (green compact) to about 73% during heating up to 1350°C. Axial shrinkage data were analyzed through the volume diffusion and grain boundary diffusion‐based sintering models. Estimated activation energy of sintering (352kJ/mol) for volume diffusion mechanism, was found to be closely matching with the reported activation energy of chromium diffusivity, indicating volume diffusion as a controlling mechanism and chromium as a major diffuser in Cr2AlC.