Marco Zedda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Marco Zedda has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Andrea Giusti
Imperial College London
2 shared publications - Johannes Heinze
Institute of Biochemistry and Biology, Biodiversity Research and Systematic Botany, University of Potsdam, Potsdam, Germany
2 shared publications - Alastair Duncan Walker
Department of Aeronautical and Automotive Engineering, Loughborough University, Loughborough, UK
1 shared publication - Andy Keane
University of Southampton
1 shared publication - Bharat Koli
Department of Aeronautical and Automotive Engineering, Loughborough University, Loughborough LE11 3TU, Leicestershire, UK
1 shared publication - Chin Yik Lee
Department of Engineering, University of Cambridge, Cambridge, UK
1 shared publication
Latest Publications
- 11 March 2021
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 143 (5)
The Potential of a Multifidelity Approach to Gas Turbine Combustor Design Optimization
The desire to reduce gas turbine emissions drives the use of design optimization approaches within the combustor design process. However, the relative cost of combustion simulations can prohibit such optimizations from being carried out within an industrial setting. Strategies which can significantly reduce the cost of such studies can enable designers to further improve emissions performance. This paper investigates the application of a multifidelity surrogate modeling approach to the design optimization of a typical gas turbine combustor from a civil airliner engine. Results over three different case studies of varying problem dimensionality indicate that a multifidelity surrogate modeling-based design optimization, whereby the simulation fidelity is varied by adjusting the coarseness of the mesh, can indeed improve optimization performance. These results indicate that such an approach has the potential to significantly reduce design optimization cost while achieving similar, or in some cases superior, design performance.
- 11 March 2021
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 143 (5)
The Potential of a Multifidelity Approach to Gas Turbine Combustor Design Optimization
The desire to reduce gas turbine emissions drives the use of design optimization approaches within the combustor design process. However, the relative cost of combustion simulations can prohibit such optimizations from being carried out within an industrial setting. Strategies which can significantly reduce the cost of such studies can enable designers to further improve emissions performance. This paper investigates the application of a multifidelity surrogate modeling approach to the design optimization of a typical gas turbine combustor from a civil airliner engine. Results over three different case studies of varying problem dimensionality indicate that a multifidelity surrogate modeling-based design optimization, whereby the simulation fidelity is varied by adjusting the coarseness of the mesh, can indeed improve optimization performance. These results indicate that such an approach has the potential to significantly reduce design optimization cost while achieving similar, or in some cases superior, design performance.
- 13 December 2019
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 142 (1)
Turbulent Flame Shape Switching at Conditions Relevant for Gas Turbines
A numerical investigation is conducted to shed light on the reasons leading to different flame configurations in gas turbine (GT) combustion chambers of aeronautical interest. Large eddy simulations (LES) with a flamelet-based combustion closure are employed for this purpose to simulate the DLR-AT big optical single sector (BOSS) rig fitted with a Rolls-Royce developmental lean burn injector. The reacting flow field downstream this injector is sensitive to the intricate turbulent–combustion interaction and exhibits two different configurations: (i) a penetrating central jet leading to an M-shape lifted flame; or (ii) a diverging jet leading to a V-shaped flame. The LES results are validated using available BOSS rig measurements, and comparisons show the numerical approach used is consistent and works well. The turbulent–combustion interaction model terms and parameters are then varied systematically to assess the flame behavior. The influences observed are discussed from physical and modeling perspectives to develop physical understanding on the flame behavior in practical combustors for both scientific and design purposes.
- 13 December 2019
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 142 (1)
Turbulent Flame Shape Switching at Conditions Relevant for Gas Turbines
A numerical investigation is conducted to shed light on the reasons leading to different flame configurations in gas turbine (GT) combustion chambers of aeronautical interest. Large eddy simulations (LES) with a flamelet-based combustion closure are employed for this purpose to simulate the DLR-AT big optical single sector (BOSS) rig fitted with a Rolls-Royce developmental lean burn injector. The reacting flow field downstream this injector is sensitive to the intricate turbulent–combustion interaction and exhibits two different configurations: (i) a penetrating central jet leading to an M-shape lifted flame; or (ii) a diverging jet leading to a V-shaped flame. The LES results are validated using available BOSS rig measurements, and comparisons show the numerical approach used is consistent and works well. The turbulent–combustion interaction model terms and parameters are then varied systematically to assess the flame behavior. The influences observed are discussed from physical and modeling perspectives to develop physical understanding on the flame behavior in practical combustors for both scientific and design purposes.
- 26 October 2018
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 141 (1)
Flow Inhomogeneities in a Realistic Aeronautical Gas-Turbine Combustor: Formation, Evolution, and Indirect Noise
Indirect noise generated by the acceleration of combustion inhomogeneities is an important aspect in the design of aero-engines because of its impact on the overall noise emitted by an aircraft and the possible contribution to combustion instabilities. In this study, a realistic rich-quench-lean (RQL) combustor is numerically investigated, with the objective of quantitatively analyzing the formation and evolution of flow inhomogeneities and determining the level of indirect combustion noise in the nozzle guide vane (NGV). Both entropy and compositional noise are calculated in this work. A high-fidelity numerical simulation of the combustion chamber, based on the large-eddy simulation (LES) approach with the conditional moment closure (CMC) combustion model, is performed. The contributions of the different air streams to the formation of flow inhomogeneities are pinned down and separated with seven dedicated passive scalars. LES-CMC results are then used to determine the acoustic sources to feed an NGV aeroacoustic model, which outputs the noise generated by entropy and compositional inhomogeneities. Results show that non-negligible fluctuations of temperature and composition reach the combustor's exit. Combustion inhomogeneities originate both from finite-rate chemistry effects and incomplete mixing. In particular, the role of mixing with dilution and liner air flows on the level of combustion inhomogeneities at the combustor's exit is highlighted. The species that most contribute to indirect noise are identified and the transfer functions of a realistic NGV are computed. The noise level indicates that indirect noise generated by temperature fluctuations is larger than the indirect noise generated by compositional inhomogeneities, although the latter is not negligible and is expected to become louder in supersonic nozzles. It is also shown that relatively small fluctuations of the local flame structure can lead to significant variations of the nozzle transfer function, whose gain increases with the Mach number. This highlights the necessity of an on-line solution of the local flame structure, which is performed in this paper by CMC, for an accurate prediction of the level of compositional noise. This study opens new possibilities for the identification, separation, and calculation of the sources of indirect combustion noise in realistic aeronautical gas turbines.
- 26 October 2018
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 141 (1)
Flow Inhomogeneities in a Realistic Aeronautical Gas-Turbine Combustor: Formation, Evolution, and Indirect Noise
Indirect noise generated by the acceleration of combustion inhomogeneities is an important aspect in the design of aero-engines because of its impact on the overall noise emitted by an aircraft and the possible contribution to combustion instabilities. In this study, a realistic rich-quench-lean (RQL) combustor is numerically investigated, with the objective of quantitatively analyzing the formation and evolution of flow inhomogeneities and determining the level of indirect combustion noise in the nozzle guide vane (NGV). Both entropy and compositional noise are calculated in this work. A high-fidelity numerical simulation of the combustion chamber, based on the large-eddy simulation (LES) approach with the conditional moment closure (CMC) combustion model, is performed. The contributions of the different air streams to the formation of flow inhomogeneities are pinned down and separated with seven dedicated passive scalars. LES-CMC results are then used to determine the acoustic sources to feed an NGV aeroacoustic model, which outputs the noise generated by entropy and compositional inhomogeneities. Results show that non-negligible fluctuations of temperature and composition reach the combustor's exit. Combustion inhomogeneities originate both from finite-rate chemistry effects and incomplete mixing. In particular, the role of mixing with dilution and liner air flows on the level of combustion inhomogeneities at the combustor's exit is highlighted. The species that most contribute to indirect noise are identified and the transfer functions of a realistic NGV are computed. The noise level indicates that indirect noise generated by temperature fluctuations is larger than the indirect noise generated by compositional inhomogeneities, although the latter is not negligible and is expected to become louder in supersonic nozzles. It is also shown that relatively small fluctuations of the local flame structure can lead to significant variations of the nozzle transfer function, whose gain increases with the Mach number. This highlights the necessity of an on-line solution of the local flame structure, which is performed in this paper by CMC, for an accurate prediction of the level of compositional noise. This study opens new possibilities for the identification, separation, and calculation of the sources of indirect combustion noise in realistic aeronautical gas turbines.
- 13 February 2018
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 140 (6)
Investigation of Flame Structure and Soot Formation in a Single Sector Model Combustor Using Experiments and Numerical Simulations Based on the Large Eddy Simulation/Conditional Moment Closure Approach
In this work, a single sector lean burn model combustor operating in pilot only mode has been investigated using both experiments and computations with the main objective of analyzing the flame structure and soot formation at conditions relevant to aero-engine applications. Numerical simulations were performed using the large eddy simulation (LES) approach and the conditional moment closure (CMC) combustion model with detailed chemistry and a two-equation model for soot. The CMC model is based on the time-resolved solution of the local flame structure and allows to directly take into account the phenomena associated to molecular mixing and turbulent transport, which are of great importance for the prediction of emissions. The rig investigated in this work, called big optical single sector rig, allows to test real scale lean burn injectors. Experiments, performed at elevated pressure and temperature, corresponding to engine conditions at part load, include planar laser-induced fluorescence of OH (OH-PLIF) and phase Doppler anemometry (PDA) and have been complemented with new laser-induced incandescence (LII) measurements for soot location. The wide range of measurements available allows a comprehensive analysis of the primary combustion region and can be exploited to further assess and validate the LES/CMC approach to capture the flame behavior at engine conditions. It is shown that the LES/CMC approach is able to predict the main characteristics of the flame with a good agreement with the experiment in terms of flame shape, spray characteristics and soot location. Finite-rate chemistry effects appear to be very important in the region close to the injection location leading to the lift-off of the flame. Low levels of soot are observed immediately downstream of the injector exit, where a high amount of vaporized fuel is still present. Further downstream, the fuel vapor disappears quite quickly and an extended region characterized by the presence of pyrolysis products and soot precursors is observed. The strong production of soot precursors together with high soot surface growth rates lead to high values of soot volume fraction in locations consistent with the experiment. Soot oxidation is also very important in the downstream region resulting in a decrease of the soot level at the combustor exit. The results show a very promising capability of the LES/CMC approach to capture the main characteristics of the flame, soot formation, and location at engine relevant conditions. More advanced soot models will be considered in future work in order to improve the quantitative prediction of the soot level.
- 13 February 2018
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 140 (6)
Investigation of Flame Structure and Soot Formation in a Single Sector Model Combustor Using Experiments and Numerical Simulations Based on the Large Eddy Simulation/Conditional Moment Closure Approach
In this work, a single sector lean burn model combustor operating in pilot only mode has been investigated using both experiments and computations with the main objective of analyzing the flame structure and soot formation at conditions relevant to aero-engine applications. Numerical simulations were performed using the large eddy simulation (LES) approach and the conditional moment closure (CMC) combustion model with detailed chemistry and a two-equation model for soot. The CMC model is based on the time-resolved solution of the local flame structure and allows to directly take into account the phenomena associated to molecular mixing and turbulent transport, which are of great importance for the prediction of emissions. The rig investigated in this work, called big optical single sector rig, allows to test real scale lean burn injectors. Experiments, performed at elevated pressure and temperature, corresponding to engine conditions at part load, include planar laser-induced fluorescence of OH (OH-PLIF) and phase Doppler anemometry (PDA) and have been complemented with new laser-induced incandescence (LII) measurements for soot location. The wide range of measurements available allows a comprehensive analysis of the primary combustion region and can be exploited to further assess and validate the LES/CMC approach to capture the flame behavior at engine conditions. It is shown that the LES/CMC approach is able to predict the main characteristics of the flame with a good agreement with the experiment in terms of flame shape, spray characteristics and soot location. Finite-rate chemistry effects appear to be very important in the region close to the injection location leading to the lift-off of the flame. Low levels of soot are observed immediately downstream of the injector exit, where a high amount of vaporized fuel is still present. Further downstream, the fuel vapor disappears quite quickly and an extended region characterized by the presence of pyrolysis products and soot precursors is observed. The strong production of soot precursors together with high soot surface growth rates lead to high values of soot volume fraction in locations consistent with the experiment. Soot oxidation is also very important in the downstream region resulting in a decrease of the soot level at the combustor exit. The results show a very promising capability of the LES/CMC approach to capture the main characteristics of the flame, soot formation, and location at engine relevant conditions. More advanced soot models will be considered in future work in order to improve the quantitative prediction of the soot level.
- Open Access
- 10 January 2017
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 139 (5) , 051504
Impact of a Cooled Cooling Air System on the External Aerodynamics of a Gas Turbine Combustion System
To manage the increasing turbine temperatures of future gas turbines a cooled cooling air system has been proposed. In such a system some of the compressor efflux is diverted for additional cooling in a heat exchanger (HX) located in the bypass duct. The cooled air must then be returned, across the main gas path, to the engine core for use in component cooling. One option is do this within the combustor module and two methods are examined in the current paper; via simple transfer pipes within the dump region or via radial struts in the prediffuser. This paper presents an experimental investigation to examine the aerodynamic impact these have on the combustion system external aerodynamics. This included the use of a fully annular, isothermal test facility incorporating a bespoke 1.5 stage axial compressor, engine representative outlet guide vanes (OGVs), prediffuser, and combustor geometry. Area traverses of a miniature five-hole probe were conducted at various locations within the combustion system providing information on both flow uniformity and total pressure loss. The results show that, compared to a datum configuration, the addition of transfer pipes had minimal aerodynamic impact in terms of flow structure, distribution, and total pressure loss. However, the inclusion of prediffuser struts had a notable impact increasing the prediffuser loss by a third and consequently the overall system loss by an unacceptable 40%. Inclusion of a hybrid prediffuser with the cooled cooling air (CCA) bleed located on the prediffuser outer wall enabled an increase of the prediffuser area ratio with the result that the system loss could be returned to that of the datum level.
- 10 January 2017
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 139 (5) , 051504
Open AccessImpact of a Cooled Cooling Air System on the External Aerodynamics of a Gas Turbine Combustion System
To manage the increasing turbine temperatures of future gas turbines a cooled cooling air system has been proposed. In such a system some of the compressor efflux is diverted for additional cooling in a heat exchanger (HX) located in the bypass duct. The cooled air must then be returned, across the main gas path, to the engine core for use in component cooling. One option is do this within the combustor module and two methods are examined in the current paper; via simple transfer pipes within the dump region or via radial struts in the prediffuser. This paper presents an experimental investigation to examine the aerodynamic impact these have on the combustion system external aerodynamics. This included the use of a fully annular, isothermal test facility incorporating a bespoke 1.5 stage axial compressor, engine representative outlet guide vanes (OGVs), prediffuser, and combustor geometry. Area traverses of a miniature five-hole probe were conducted at various locations within the combustion system providing information on both flow uniformity and total pressure loss. The results show that, compared to a datum configuration, the addition of transfer pipes had minimal aerodynamic impact in terms of flow structure, distribution, and total pressure loss. However, the inclusion of prediffuser struts had a notable impact increasing the prediffuser loss by a third and consequently the overall system loss by an unacceptable 40%. Inclusion of a hybrid prediffuser with the cooled cooling air (CCA) bleed located on the prediffuser outer wall enabled an increase of the prediffuser area ratio with the result that the system loss could be returned to that of the datum level.