Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Alastair Duncan Walker has a total of 55 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Characteristic Time Scale Modeling of Gas Turbine Combustor Ignition Limits at Sub Idle Conditions

    by Calum Hargreaves, Paul Denman, Dimitri Franz, Ian Mariah, Jon F. Carrotte, A. Duncan Walker

    This paper presents a study of aerospace gas turbine combustor operability performance to capture the lean boundaries of ignition at sub idle conditions. Presented in previous literature, the characteristic time scale method of ignition modeling (CTM) captures the time scales of the droplet evaporation and the chemical reaction processes and limits these against the aerodynamic time scale available for the droplet ignition to occur. In this study, the method was applied to experimental datasets taken over a range of pressures and temperatures within the sub idle operating regime, typically seen in a combustor during ignition at altitude. High-speed imaging of the initial 1.0 ms of ignition was undertaken to examine the effect of inlet pressure and temperature on expansion of an unfueled spark, and the impact of fuel on the initial growth of this kernel to assess model input assumptions. The predicted changes in ignition boundaries with variation of inlet pressure and temperature were evaluated against experimental ignition loop datasets. The model was found to give a good prediction of the mass flow and fuel-air ratio (FAR) ignition limits for the inlet air pressures and temperatures tested. The evaporation time scale was demonstrated to dominate ignition when the pressure drop across the test section was low. This was driven by poor atomization of fuel at reduced mass flow rates through the fuel spray nozzle (FSN). As the test section pressure drop was increased, the chemical reaction processes were seen to dominate, due to reduced droplet size driving a reduction in evaporation time scales.

  • Open Access

    Effect of arm position on the aerodynamic drag of an individual time trial position

    by Phillip Maddocks, A. Duncan Walker

    In an individual time trial elite cyclists strive to reduce aerodynamic drag through the optimisation of body position. This paper presents an aerodynamic investigation into the effect of arm position on drag using Computational Fluid Dynamics. The lowest drag was achieved by moving the hands/arms into a higher position in conjunction to narrowing the elbows better guided the air over the rider’s head and away from the centre of the rider’s body. This gave a reduction in drag area of 11.2% which would translate to a time saving of about 91 s for a 40 km time trial ridden at 14 m/s (50.4 km/h). For all positions about half the drag generated by the rider was produced by the legs. A lower hand position was observed to reduce the drag from the legs but with no net gain as drag from the head, arms and body increased. For the positions tested a reduction in projected frontal area did not automatically reduce aerodynamic drag. A more complex relationship between area and aerodynamic drag coefficient existed. However, the results show clear potential for (i) better aerodynamic integration of the arms with the legs or (ii) raising the rider’s head into a safe forward-looking position without compromising the aerodynamic drag.


  • Open Access

    Principal Component Analysis and K-Means Clustering of Fuel-Air Mixing in Gas Turbine Combustors

    by David Salvador-Jasin, A Duncan Walker, Jon F Carrotte

    As a direct consequence of liquid kerosene injection, aeroengine combustors may be categorized as non-premixed combustion systems, characterized by a swirl-stabilized and highly complex flow field. In addition to the flow of air through the fuel injector, there are a large number of other features through which oxidizer can enter the heat release region. These can have an impact on local fuel-air mixing, inducing strong spatial and temporal variations in stoichiometry, thereby affecting emissions and combustion system performance. This paper discusses a novel statistical methodology, based on Principal Component Analysis (PCA) and K-means clustering, that aims to improve understanding of fuel-air mixing in realistic aeroengine combustors. The method is applied in a postprocessing step to data sampled from a Large Eddy Simulation (LES), where every chamber inflow has been tagged with a unique passive scalar, which allows it to be traced across space and time. PCA is used to construct a low-dimensional, visually interpretable representation of a spatially localized fuel-air mixing process, while K-means clustering is employed to produce an unsupervised discretization of the flow field into regions of similar fuel-air mixing characteristics. The proposed methodology is computationally inexpensive, and the easily interpretable outputs can help the combustion engineer make better informed decisions about combustor design.

  • Open Access

    Practical computational fluid dynamic predictions of a cyclist in a time trial position

    by Morgan Taylor, Daniel Butcher, Conor Crickmore, A. Duncan Walker

    On a flat road, at race speeds, aerodynamic drag is the main resistive force a cyclist must overcome. Computational fluid dynamics (CFD) can be a useful tool to predict and understand the complex flow and, therefore, drive developments to reduce drag. However, cycling aerodynamics is complex. The effects of Reynolds number, surface roughness, boundary layer transition, flow separation, and turbulent wakes are challenging to accurately predict. High fidelity time-resolved computations, such as Large eddy simulations (LES), require high-performance computing and lengthy simulation times. This paper examines whether lower fidelity CFD, such as Reynolds averaged approaches, can predict the drag of a cyclist with sufficient accuracy and within practical timescales on a desktop PC. Wind tunnel tests of a rider model (without bicycle) were conducted at Reynolds numbers equivalent to speeds of ~ 20–70 km/h. Measured drag showed a notable Reynolds number dependency with the drag coefficient reducing almost linearly by ~ 20% from 0.88 to 0.71. The computational accurately replicated this relationship but only when employing a boundary layer transition model. The steady computations underpredicted the magnitude of the measured drag coefficient by ~ 3% but the unsteady computations were within ~ 2%. Examination of the predicted flow field revealed variations in boundary layer transition, separation, and wake formation from each body part which combine in a complex wake system. Overall, the data confirm validity and suitable accuracy of the CFD, and therefore this provides a practical time and cost-effective tool for further examination of drag reduction within cycling.


  • Experimental Investigation of the Effect of Bleed on the Aerodynamics of a Low-Pressure Compressor Stage in a Turbofan Engine

    by Apostolos Spanelis, Paul A. Denman, Ian Mariah, A. Duncan Walker

    The compression system in modern turbofan engines is split into stages linked by transition ducts. Downstream of the low-pressure system, a handling bleed is often required and, in conjunction with structural vanes, can introduce component interactions, which compromise aerodynamic performance. In this paper, a fully annular, low-speed test facility incorporating a 1½ stage axial compressor is used to examine the flow in the last stage of a low-pressure compressor and the downstream transition duct. The transition duct incorporated load-bearing struts, including a so-called king strut with twice the thickness of the regular struts. The bleed utilized a 360-deg annular slot located on the casing immediately downstream of the low-pressure rotor and upstream of the outlet guide vane. The results showed that both the regular and king strut caused a similar flow distortion in the vane row but overall imposed a negligible effect on overall performance. The addition of bleed had a larger effect, generating an increasing outboard bias at the rotor exit as the bleed flow migrated toward the offtake. At the design operating point, the outlet guide vanes were relatively insensitive to this until the highest bleed rate (18%) where evidence of stall was observed. At a lower operating point, a modification to the rotor swirl caused additional incidence onto the vanes, resulting in an earlier onset of the stall; a full stall was observed above 10% bleed. Increasing bleed caused a gradual increase in duct loss up to stall when losses increased rapidly.


  • Open Access

    Flight dynamics of ski jumping: Wind tunnel testing and numerical modeling to optimize flight position

    by Jason Barnes, Simon Tuplin, Alastair Duncan Walker

    Ski jumping is a highly competitive sport, where the distance jumped is greatly dependent on the aerodynamic effects of the athlete’s posture. In the current paper a wind tunnel experiment was conducted to generate a parametric database of the effects of posture on aerodynamics and to compute the aerodynamic force coefficients. The parameters considered were varied over ranges representative of modern ski jumping and included the ski incidence angle, the ski V-angle, the leg-to-ski angle, and the hip angle. Measured force data were then used to simulate ski jumping flightpaths via a numerical model, allowing for the effects of posture on jump distance to be investigated. The model was able to simulate single and multi-posture flights to suggest both static and dynamic optimums. It was found that the ski jumping system generated lift in previously unreported, non-linear methods, enabling the flow to stay attached at much larger incidences than traditional wings. When optimizing posture for distance, it was found that neither lift nor efficiency (lift-to-drag ratio) should be maximized, due to the reliance on both qualities for a successful jump. However, when considering multi-posture flight, it was found that the lift-to-drag ratio should be maximized immediately after take-off, to maintain horizontal velocity. Lift should be maximized as the athlete approaches landing, due to the highly curved flightpath reducing the negative impact of drag. Realistic recommendations have been made on the postures that athletes should utilize to improve their performance. This includes a single position optimum, a “safe” optimum which allows some variation in an athlete’s ability to hold posture, and a further optimum should the athlete be skillful enough to dynamically alter posture as the jump progresses.


  • Open Access

    A Multi-Objective Factorial Design Methodology for Aerodynamic Off-Takes and Ducts

    by Apostolos Spanelis, Alastair Duncan Walker

    Fluid off-takes and complex delivery ducts are common in many engineering systems but designing them can be a challenging task. At the conceptual design phase many system parameters are open to consideration and preliminary design studies are necessary to instruct the conceptualisation process in an iterative development of design ideas. This paper presents a simple methodology to parametrically design, explore and optimise such systems at low cost. The method is then applied to an aerodynamic system including an off-take followed by a complex delivery duct. A selection of nine input variables is explored via a fractional factorial design approach that consists of three individual seven-level cubic factorial designs. Numerical predictions are characterised based on multiple aerodynamic objectives. A scaled representation of these objectives allows for a scalarisation technique to be employed in the form of a global criterion which indicates a set of trade-off geometries. This leads to the selection of a set of nominal designs and the determination of their robustness which will eventually instruct the next conceptual design iteration. The results are presented and discussed based on criterion space, design variable space and contours of several flow quantities on a selection of optimal geometries.


  • Experimental Investigation of Secondary Flows and Length Reduction for a Low-Pressure Compressor Transition Duct

    by Dimitra Tsakmakidou, Ian Mariah, A. Duncan Walker, Chris Hall, Harry Simpson

    The need to reduce fuel-burn and emissions is pushing turbofan engines toward geared architectures with higher bypass ratios and small ultrahigh-pressure ratio cores. However, this increases the radial offset between compressor spools leading to a more challenging design for compressor transition ducts. For the duct connecting the fan to the engine core, this is further complicated by poor-quality flow generated at the fan hub, which is characterized by low total pressure and large rotating secondary flow structures. This paper presents an experimental evaluation of a new rotor designed to produce these larger flow structures and examines their effect on the performance of an engine sector stators (ESS) and compressor transition duct. Aerodynamic data were collected via five-hole probes, for time-averaged pressures and velocities and phase-locked hot-wire anemometry to capture the rotating secondary flows. The data showed that larger structures promoted mixing through the ESS increasing momentum exchange between the core and boundary layer flows. Measurements within the duct showed a continued reduction in the hub boundary layer, suggesting the duct had moved further from separation. Consequently, an aggressive duct with 12.5% length reduction was designed and tested and measurements confirmed the duct remained fully attached. Total pressure loss was slightly increased over the ESS, but this was offset by reduced loss in the duct due to improved flow quality. Overall, this length reduction represents a significant cumulative effect in reduced fuel-burn and emissions over the life of an engine.


  • Aerodynamic Influence of a Bleed on the Last Stage of a Low-Pressure Compressor and S-Duct

    by Apostolos Spanelis, A. Duncan Walker

    This paper uses computational fluid dynamics to investigate the effect of an engine handling bleed situated on the outer casing downstream of the last rotor stage of a low-pressure compressor and upstream of the outlet guide vane and S-shaped duct. The model, validated against existing experimental data, utilized an unsteady Reynolds-averaging Navier–Stokes (RANS) solver incorporating a Reynolds stress closure to examine the unsteady component interactions. The results showed that at bleed rates less than 25% of the mainstream flow, the bleed effects were negligible. However, at higher bleed rates, performance was significantly degraded. A uniform flow extraction hypothesis was employed to separate the positional bias effects of the bleed from the bulk flow diffusion. This revealed that the bleed-induced radial flow distortion can significantly affect the outlet guide vane (OGV) loading distribution, which thereby dictates the position and type of stall within the OGV passage. Extraction of the rotor tip leakage via the shroud bleed, combined with the radial flow distortion, contributed to a 28% reduction in duct loss at 10% bleed and up to 50% reduced loss at 25% bleed. The actual amount of flow required to be extracted for an OGV stall to develop was 30%. That was independent of the bleed location and the type of stall. For bleeds up to 20%, the S-duct displayed a remarkable resilience and consistency of flow variables at duct exit. However, a stalled OGV deteriorated the radial flow uniformity that was presented to the high-pressure compressor.


  • Open Access

    An Experimental, Aerodynamic Evaluation of Design Choices for a Low-Pressure Compressor Transition Duct

    by Ian Mariah, A Duncan Walker, Chris Hall

    The S-shaped duct which transfers flow from the low-pressure fan to the engine core of modern large civil turbofans presents a challenging design problem. Aerodynamically it must accommodate a spatially and temporarily non-uniform inlet in conjunction with a complex flow field which will develop under the combined influence of pressure gradients and streamline curvature. It must