Andrew F. Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andrew F. Chen has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Je-Chin Han
Texas A&M University Turbine Heat Transfer Laboratory, Department of Mechanical Engineering College Station, TX 77843
5 shared publications - Chao-Cheng Shiau
Turbine Heat Transfer Laboratory, Department of Mechanical Engineering, Texas A&M University, College Station, TX 77843-3123
3 shared publications - Hao-Wei Wu
Turbine Heat Transfer Laboratory, Department of Mechanical Engineering, Texas A&M University, College Station, TX 77843-3123
2 shared publications - Ching-Pang Lee
Siemens Energy, Inc., 4400 Alafaya Trail, Orlando, FL 32826
1 shared publication - Jae Um
Siemens Energy, Inc., 4400 Alafaya Trail, Orlando, FL 32826
1 shared publication - Lesley M. Wright
Texas A&M University Turbine Heat Transfer Laboratory, Department of Mechanical Engineering College Station, TX 77843
1 shared publication
Latest Publications
- 22 January 2021
- Published by Wiley in Journal of Thermal Science and Engineering Applications
- Vol. 13 (4) , 1-29
Heat Transfer Enhancement in a Rectangular Cooling Channel With Airfoil Shaped Fins
This paper experimentally investigates heat transfer in a cooling passage with airfoil shaped fins for channel Reynolds numbers 10,000–40,000. This study uses airfoil shaped fins, instead of circular or oblong-shaped pins, for heat transfer augmentation. The airfoil shaped fins have more surface area than traditional pins. Assuming they both provide similar internal surface heat transfer coefficients, airfoil shaped fins will perform better than circular or oblong fins due to increased surface area. There is a need to obtain the heat transfer enhancement and pressure drop penalty in this cooling passage with airfoil shaped fins. Results are compared to the same rectangular cooling channel with smooth surfaces. The heat transfer can be enhanced 6–8 times while pressure drop is increased 70–90 times, as compared with the same channel with a smooth surface. With the fins significantly increasing the heat transfer area, three different methods are proposed for analyzing the heat transfer enhancement: (a) using the smooth channel area with the endwall temperature, (b) combining the total heat transfer area with the endwall temperature, and (c) coupling the total heat transfer area with the area weighted, average temperature including both the endwall and fin temperatures. Finally, compared directly to round pins, the airfoil shaped fins incur similar pressure penalties while providing slightly less heat transfer. The airfoil shaped fins benefit from a significant increase in the heat transfer area, a characteristic similar to more narrow strip fins.
- 22 January 2021
- Published by Wiley in Journal of Thermal Science and Engineering Applications
- Vol. 13 (4) , 1-29
Heat Transfer Enhancement in a Rectangular Cooling Channel With Airfoil Shaped Fins
This paper experimentally investigates heat transfer in a cooling passage with airfoil shaped fins for channel Reynolds numbers 10,000–40,000. This study uses airfoil shaped fins, instead of circular or oblong-shaped pins, for heat transfer augmentation. The airfoil shaped fins have more surface area than traditional pins. Assuming they both provide similar internal surface heat transfer coefficients, airfoil shaped fins will perform better than circular or oblong fins due to increased surface area. There is a need to obtain the heat transfer enhancement and pressure drop penalty in this cooling passage with airfoil shaped fins. Results are compared to the same rectangular cooling channel with smooth surfaces. The heat transfer can be enhanced 6–8 times while pressure drop is increased 70–90 times, as compared with the same channel with a smooth surface. With the fins significantly increasing the heat transfer area, three different methods are proposed for analyzing the heat transfer enhancement: (a) using the smooth channel area with the endwall temperature, (b) combining the total heat transfer area with the endwall temperature, and (c) coupling the total heat transfer area with the area weighted, average temperature including both the endwall and fin temperatures. Finally, compared directly to round pins, the airfoil shaped fins incur similar pressure penalties while providing slightly less heat transfer. The airfoil shaped fins benefit from a significant increase in the heat transfer area, a characteristic similar to more narrow strip fins.
- 22 May 2019
- Published by Wiley in Journal of Thermal Science and Engineering Applications
- Vol. 11 (6) , 1-42
Heat Transfer in a Rotating Two-Pass Rectangular Channel Featuring a Converging Tip Turn With Various 45 deg Rib Coverage Designs
Varying aspect ratio (AR) channels are found in modern gas turbine airfoils for internal cooling purposes. Corresponding experimental data are needed in understanding and assisting the design of advanced cooling systems. The present study features a two-pass rectangular channel with an AR = 4:1 in the first pass with the radial outward flow and an AR = 2:1 in the second pass with the radial inward flow after a 180 deg tip turn. Effects of rib coverage near the tip region are investigated using profiled 45 deg ribs (P/e = 10, e/Dh ≈ 0.11, parallel and in-line) with three different configurations: less coverage, medium coverage, and full coverage. The Reynolds number (Re) ranges from 10,000 to 70,000 in the first passage. The highest rotation number achieved was Ro = 0.39 in the first passage and 0.16 in the second passage. Heat transfer coefficients on the internal surfaces were obtained by the regionally averaged copper plate method. The results showed that the rotation effects on both heat transfer and pressure loss coefficient are reduced with an increased rib coverage in the tip turn region. Different rib coverage upstream of the tip turn significantly changes the heat transfer in the turn portion. Heat transfer reduction (up to −27%) on the tip wall was seen at lower Ro. Dependence on the Reynolds number can be seen for this particular design. The combined geometric, rib coverage, and rotation effects should be taken into consideration in the internal cooling design.
- 22 May 2019
- Published by Wiley in Journal of Thermal Science and Engineering Applications
- Vol. 11 (6) , 1-42
Heat Transfer in a Rotating Two-Pass Rectangular Channel Featuring a Converging Tip Turn With Various 45 deg Rib Coverage Designs
Varying aspect ratio (AR) channels are found in modern gas turbine airfoils for internal cooling purposes. Corresponding experimental data are needed in understanding and assisting the design of advanced cooling systems. The present study features a two-pass rectangular channel with an AR = 4:1 in the first pass with the radial outward flow and an AR = 2:1 in the second pass with the radial inward flow after a 180 deg tip turn. Effects of rib coverage near the tip region are investigated using profiled 45 deg ribs (P/e = 10, e/Dh ≈ 0.11, parallel and in-line) with three different configurations: less coverage, medium coverage, and full coverage. The Reynolds number (Re) ranges from 10,000 to 70,000 in the first passage. The highest rotation number achieved was Ro = 0.39 in the first passage and 0.16 in the second passage. Heat transfer coefficients on the internal surfaces were obtained by the regionally averaged copper plate method. The results showed that the rotation effects on both heat transfer and pressure loss coefficient are reduced with an increased rib coverage in the tip turn region. Different rib coverage upstream of the tip turn significantly changes the heat transfer in the turn portion. Heat transfer reduction (up to −27%) on the tip wall was seen at lower Ro. Dependence on the Reynolds number can be seen for this particular design. The combined geometric, rib coverage, and rotation effects should be taken into consideration in the internal cooling design.
- 8 June 2018
- Published by Wiley in Journal of Heat Transfer
- Vol. 140 (10) , 102007
Heat Transfer in a Rotating Cooling Channel (AR = 2:1) With Rib Turbulators and a Tip Turning Vane
Experimental investigation on rotation and turning vane effects on heat transfer was performed in a two-pass rectangular internal cooling channel. The channel has an aspect ratio of AR = 2:1 and a 180 deg tip-turn, which is a scaled up model of a typical internal cooling passage of gas turbine airfoils. The leading surface (LS) and trailing surface (TS) are roughened with 45 deg angled parallel ribs (staggered P/e = 8, e/Dh = 0.1). Tests were performed in a pressurized vessel (570 kPa) where higher rotation numbers (Ro) can be achieved with a maximum Ro = 0.42. Five Reynolds numbers (Re) were examined (Re = 10,000–40,000). At each Reynolds number, five rotational speeds (Ω = 0–400 rpm) were considered. Results showed that rotation effects are stronger in the tip regions as compared to other surfaces. Heat transfer enhancement up to four times was observed on the tip wall at the highest rotation number. However, heat transfer enhancement is reduced to about 1.5 times with the presence of a tip turning vane at the highest rotation number. Generally, the tip turning vane reduces the effects of rotation, especially in the turn portion.
- 8 June 2018
- Published by Wiley in Journal of Heat Transfer
- Vol. 140 (10) , 102007
Heat Transfer in a Rotating Cooling Channel (AR = 2:1) With Rib Turbulators and a Tip Turning Vane
Experimental investigation on rotation and turning vane effects on heat transfer was performed in a two-pass rectangular internal cooling channel. The channel has an aspect ratio of AR = 2:1 and a 180 deg tip-turn, which is a scaled up model of a typical internal cooling passage of gas turbine airfoils. The leading surface (LS) and trailing surface (TS) are roughened with 45 deg angled parallel ribs (staggered P/e = 8, e/Dh = 0.1). Tests were performed in a pressurized vessel (570 kPa) where higher rotation numbers (Ro) can be achieved with a maximum Ro = 0.42. Five Reynolds numbers (Re) were examined (Re = 10,000–40,000). At each Reynolds number, five rotational speeds (Ω = 0–400 rpm) were considered. Results showed that rotation effects are stronger in the tip regions as compared to other surfaces. Heat transfer enhancement up to four times was observed on the tip wall at the highest rotation number. However, heat transfer enhancement is reduced to about 1.5 times with the presence of a tip turning vane at the highest rotation number. Generally, the tip turning vane reduces the effects of rotation, especially in the turn portion.
- 25 October 2017
- Published by Wiley in Journal of Turbomachinery
- Vol. 140 (1) , 011006
Turbine Blade Platform Film Cooling With Fan-Shaped Holes Under Simulated Swirl Purge Flow and Slashface Leakage Conditions
The combined effects of upstream purge flow, slashface leakage flow, and discrete hole film cooling on turbine blade platform film cooling effectiveness were studied using the pressure sensitive paint (PSP) technique. As a continued study, discrete cylindrical holes were replaced by laidback fan-shaped (10-10-5) holes, which generally provide better film coverages on the endwall. Experiments were done in a five-blade linear cascade. The inlet and exit Mach numbers were 0.26 and 0.43, respectively. The inlet and exit mainstream Reynolds numbers based on the axial chord length of the blade were 475,000 and 720,000, respectively. A wide range of parameters was evaluated in this study. The coolant-to-mainstream mass flow ratio (MFR) was varied from 0.5%, 0.75%, to 1% for the upstream purge flow. For the platform film cooling holes and slashface gap, average blowing ratios (M) of 0.5, 1.0, and 1.5 were examined. Coolant-to-mainstream density ratios (DR) that range from 1 (close to low-temperature experiments) to 1.5 (intermediate DR) and 2 (close to engine conditions) were also examined. Purge flow swirl effect was studied particularly at a typical swirl ratio (SR) of 0.6. Area-averaged film cooling effectiveness results were compared between cylindrical and fan-shaped holes. The results indicate that the fan-shaped holes provide superior film coverage than cylindrical holes for platform film cooling especially at higher blowing ratios and momentum flux ratios.
- 25 October 2017
- Published by Wiley in Journal of Turbomachinery
- Vol. 140 (1) , 011006
Turbine Blade Platform Film Cooling With Fan-Shaped Holes Under Simulated Swirl Purge Flow and Slashface Leakage Conditions
The combined effects of upstream purge flow, slashface leakage flow, and discrete hole film cooling on turbine blade platform film cooling effectiveness were studied using the pressure sensitive paint (PSP) technique. As a continued study, discrete cylindrical holes were replaced by laidback fan-shaped (10-10-5) holes, which generally provide better film coverages on the endwall. Experiments were done in a five-blade linear cascade. The inlet and exit Mach numbers were 0.26 and 0.43, respectively. The inlet and exit mainstream Reynolds numbers based on the axial chord length of the blade were 475,000 and 720,000, respectively. A wide range of parameters was evaluated in this study. The coolant-to-mainstream mass flow ratio (MFR) was varied from 0.5%, 0.75%, to 1% for the upstream purge flow. For the platform film cooling holes and slashface gap, average blowing ratios (M) of 0.5, 1.0, and 1.5 were examined. Coolant-to-mainstream density ratios (DR) that range from 1 (close to low-temperature experiments) to 1.5 (intermediate DR) and 2 (close to engine conditions) were also examined. Purge flow swirl effect was studied particularly at a typical swirl ratio (SR) of 0.6. Area-averaged film cooling effectiveness results were compared between cylindrical and fan-shaped holes. The results indicate that the fan-shaped holes provide superior film coverage than cylindrical holes for platform film cooling especially at higher blowing ratios and momentum flux ratios.
- 1 December 2016
- Published by Wiley in Journal of Turbomachinery
- Vol. 139 (3) , 031012
Turbine Blade Platform Film Cooling With Simulated Swirl Purge Flow and Slashface Leakage Conditions
The combined effects of inlet purge flow and the slashface leakage flow on the film cooling effectiveness of a turbine blade platform were studied using the pressure-sensitive paint (PSP) technique. Detailed film cooling effectiveness distributions on the endwall were obtained and analyzed. Discrete cylindrical film cooling holes were arranged to achieve an improved coverage on the endwall. Backward injection was attempted by placing backward injection holes near the pressure side leading edge portion. Experiments were done in a five-blade linear cascade with an average turbulence intensity of 10.5%. The inlet and exit Mach numbers were 0.26 and 0.43, respectively. The inlet and exit mainstream Reynolds numbers based on the axial chord length of the blade were 475,000 and 720,000, respectively. The coolant-to-mainstream mass flow ratios (MFR) were varied from 0.5% and 0.75% to 1% for the purge flow. For the endwall film cooling holes and slashface leakage flow, blowing ratios (M) of 0.5, 1.0, and 1.5 were examined. Coolant-to-mainstream density ratios (DR) that range from 1.0 (close to low temperature experiments) to 1.5 and 2.0 (close to engine conditions) were also examined. The results provide the gas turbine engine designers a better insight into improved film cooling hole configurations as well as various parametric effects on endwall film cooling when the inlet (swirl) purge flow and slashface leakage flow were incorporated.
- 1 December 2016
- Published by Wiley in Journal of Turbomachinery
- Vol. 139 (3) , 031012
Turbine Blade Platform Film Cooling With Simulated Swirl Purge Flow and Slashface Leakage Conditions
The combined effects of inlet purge flow and the slashface leakage flow on the film cooling effectiveness of a turbine blade platform were studied using the pressure-sensitive paint (PSP) technique. Detailed film cooling effectiveness distributions on the endwall were obtained and analyzed. Discrete cylindrical film cooling holes were arranged to achieve an improved coverage on the endwall. Backward injection was attempted by placing backward injection holes near the pressure side leading edge portion. Experiments were done in a five-blade linear cascade with an average turbulence intensity of 10.5%. The inlet and exit Mach numbers were 0.26 and 0.43, respectively. The inlet and exit mainstream Reynolds numbers based on the axial chord length of the blade were 475,000 and 720,000, respectively. The coolant-to-mainstream mass flow ratios (MFR) were varied from 0.5% and 0.75% to 1% for the purge flow. For the endwall film cooling holes and slashface leakage flow, blowing ratios (M) of 0.5, 1.0, and 1.5 were examined. Coolant-to-mainstream density ratios (DR) that range from 1.0 (close to low temperature experiments) to 1.5 and 2.0 (close to engine conditions) were also examined. The results provide the gas turbine engine designers a better insight into improved film cooling hole configurations as well as various parametric effects on endwall film cooling when the inlet (swirl) purge flow and slashface leakage flow were incorporated.