Christopher Robak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Christopher Robak has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Karen A. Thole
Pennsylvania State University Department of Mechanical Engineering 3127 Research Drive, State College, PA 16801
3 shared publications - Michael D. Barringer
The Pennsylvania State University Department of Mechanical Engineering University Park, PA 16802
2 shared publications - Carey Clum
Pratt & Whitney, East Hartford, CT 06118
1 shared publication - Curtis Memory
Pratt & Whitney, East Hartford, CT 06118
1 shared publication David Johnson
Department of Mechanical and Nuclear Engineering, The Pennsylvania State University, University Park, PA 16802
1 shared publication- E. A. Grover
Pratt & Whitney, East Hartford, CT 06118
1 shared publication
Latest Publications
- 1 February 2021
- Published by Wiley in Journal of Turbomachinery
- Vol. 143 (2) , 1-55
Evaluating the Effects of Transient Purge Flow on Stator-Rotor Seal Performance
As modern engine designs target higher efficiencies through increased turbine inlet temperatures, critical turbine components are at increased risk of damage from conditions exceeding material melting temperatures. In particular, improperly designed underplatform hardware components are susceptible to damage when hot main gas path flow is ingested into the stator-rotor cavity. While all turbines inherently experience transients during operation, a majority of publicly available turbine studies have been executed using steady operating conditions or inherently transient “blowdown” rigs. For this reason, routine transient events are not well understood. To address this need, the present study utilized a combined experimental and computational approach. The test article is a continuous-duration, one-stage test turbine operating with true-scale engine hardware and seal geometries at engine-representative flow conditions. The nature of the continuous-duration facility uniquely supports the direct assessment of transient events through its ability to transition between steady-state operating conditions. The effects of a transient purge flow were investigated in this study to identify general trends for transient events in a full-scale engine. Results from multiple measurement techniques in the wheelspace region show an interdependence of transient purge flow with a thermal lag of the underplatform hardware. Through experiments conducted at different coolant-to-main gas path temperature ratios, the use of pressure measurements as an indicator of fully purged behavior was introduced, and a thermally driven influence on rim seal performance was quantified. The computational results show good agreement with experimental pressure measurements and provide insight into the physical mechanisms that drive the relationship between pressure and sealing effectiveness measurements observed for the tested geometry.
- 1 February 2021
- Published by Wiley in Journal of Turbomachinery
- Vol. 143 (2) , 1-55
Evaluating the Effects of Transient Purge Flow on Stator-Rotor Seal Performance
As modern engine designs target higher efficiencies through increased turbine inlet temperatures, critical turbine components are at increased risk of damage from conditions exceeding material melting temperatures. In particular, improperly designed underplatform hardware components are susceptible to damage when hot main gas path flow is ingested into the stator-rotor cavity. While all turbines inherently experience transients during operation, a majority of publicly available turbine studies have been executed using steady operating conditions or inherently transient “blowdown” rigs. For this reason, routine transient events are not well understood. To address this need, the present study utilized a combined experimental and computational approach. The test article is a continuous-duration, one-stage test turbine operating with true-scale engine hardware and seal geometries at engine-representative flow conditions. The nature of the continuous-duration facility uniquely supports the direct assessment of transient events through its ability to transition between steady-state operating conditions. The effects of a transient purge flow were investigated in this study to identify general trends for transient events in a full-scale engine. Results from multiple measurement techniques in the wheelspace region show an interdependence of transient purge flow with a thermal lag of the underplatform hardware. Through experiments conducted at different coolant-to-main gas path temperature ratios, the use of pressure measurements as an indicator of fully purged behavior was introduced, and a thermally driven influence on rim seal performance was quantified. The computational results show good agreement with experimental pressure measurements and provide insight into the physical mechanisms that drive the relationship between pressure and sealing effectiveness measurements observed for the tested geometry.
- 12 July 2018
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 140 (11)
Effects of Purge Flow Configuration on Sealing Effectiveness in a Rotor–Stator Cavity
Secondary air is bled from the compressor in a gas turbine engine to cool turbine components and seal the cavities between stages. Unsealed cavities can lead to hot gas ingestion, which can degrade critical components or, in extreme cases, can be catastrophic to engines. For this study, a 1.5 stage turbine with an engine-realistic rim seal was operated at an engine-relevant axial Reynolds number, rotational Reynolds number, and Mach number. Purge flow was introduced into the interstage cavity through distinct purge holes for two different configurations. This paper compares the two configurations over a range of purge flow rates. Sealing effectiveness measurements, deduced from the use of CO2 as a flow tracer, indicated that the sealing characteristics were improved by increasing the number of uniformly distributed purge holes and improved by increasing levels of purge flow. For the larger number of purge holes, a fully sealed cavity was possible, while for the smaller number of purge holes, a fully sealed cavity was not possible. For this representative cavity model, sealing effectiveness measurements were compared with a well-accepted orifice model derived from simplified cavity models. Sealing effectiveness levels at some locations within the cavity were well-predicted by the orifice model, but due to the complexity of the realistic rim seal and the purge flow delivery, the effectiveness levels at other locations were not well-predicted.
- 12 July 2018
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 140 (11)
Effects of Purge Flow Configuration on Sealing Effectiveness in a Rotor–Stator Cavity
Secondary air is bled from the compressor in a gas turbine engine to cool turbine components and seal the cavities between stages. Unsealed cavities can lead to hot gas ingestion, which can degrade critical components or, in extreme cases, can be catastrophic to engines. For this study, a 1.5 stage turbine with an engine-realistic rim seal was operated at an engine-relevant axial Reynolds number, rotational Reynolds number, and Mach number. Purge flow was introduced into the interstage cavity through distinct purge holes for two different configurations. This paper compares the two configurations over a range of purge flow rates. Sealing effectiveness measurements, deduced from the use of CO2 as a flow tracer, indicated that the sealing characteristics were improved by increasing the number of uniformly distributed purge holes and improved by increasing levels of purge flow. For the larger number of purge holes, a fully sealed cavity was possible, while for the smaller number of purge holes, a fully sealed cavity was not possible. For this representative cavity model, sealing effectiveness measurements were compared with a well-accepted orifice model derived from simplified cavity models. Sealing effectiveness levels at some locations within the cavity were well-predicted by the orifice model, but due to the complexity of the realistic rim seal and the purge flow delivery, the effectiveness levels at other locations were not well-predicted.
- 4 October 2016
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 139 (3) , 031904
Effects of Purge Jet Momentum on Sealing Effectiveness
Driven by the need for higher cycle efficiencies, overall pressure ratios for gas turbine engines continue to be pushed higher thereby resulting in increasing gas temperatures. Secondary air, bled from the compressor, is used to cool turbine components and seal the cavities between stages from the hot main gas path. This paper compares a range of purge flows and two different purge hole configurations for introducing the purge flow into the rim cavities. In addition, the mate face gap leakage between vanes is investigated. For this particular study, stationary vanes at engine-relevant Mach and Reynolds numbers were used with a static rim seal and rim cavity to remove rotational effects and isolate gas path effects. Sealing effectiveness measurements, deduced from the use of CO2 as a flow tracer, indicate that the effectiveness levels on the stator and rotor side of the cavity depend on the mass and momentum flux ratios of the purge jets relative to the swirl velocity. For a given purge flow rate, fewer purge holes resulted in better sealing than the case with a larger number of holes.
- 4 October 2016
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 139 (3) , 031904
Effects of Purge Jet Momentum on Sealing Effectiveness
Driven by the need for higher cycle efficiencies, overall pressure ratios for gas turbine engines continue to be pushed higher thereby resulting in increasing gas temperatures. Secondary air, bled from the compressor, is used to cool turbine components and seal the cavities between stages from the hot main gas path. This paper compares a range of purge flows and two different purge hole configurations for introducing the purge flow into the rim cavities. In addition, the mate face gap leakage between vanes is investigated. For this particular study, stationary vanes at engine-relevant Mach and Reynolds numbers were used with a static rim seal and rim cavity to remove rotational effects and isolate gas path effects. Sealing effectiveness measurements, deduced from the use of CO2 as a flow tracer, indicate that the effectiveness levels on the stator and rotor side of the cavity depend on the mass and momentum flux ratios of the purge jets relative to the swirl velocity. For a given purge flow rate, fewer purge holes resulted in better sealing than the case with a larger number of holes.