Zhiqiang Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zhiqiang Yang has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Minghui Yin
School of Automation, Nanjing University of Science and Technology, Nanjing, China
2 shared publications - Yan Xu
Nanyang Technological University
2 shared publications - Yun Zou
School of Automation, Nanjing University of Science and Technology, Nanjing, China
2 shared publications - Zhao Yang Dong
City University of Hong Kong
2 shared publications - Qian Zhou
State Grid Jiangsu Electric Power Research Institute, Nanjing 211100, China
1 shared publication - Zhengyang Zhang
School of Automation, Nanjing University of Science and Technology, Nanjing 210094, China
1 shared publication
Latest Publications
- Open Access
Inverse Aerodynamic Optimization Considering Impacts of Design Tip Speed Ratio for Variable-Speed Wind Turbines
Because of the slow dynamic behavior of the large-inertia wind turbine rotor, variable-speed wind turbines (VSWTs) are actually unable to keep operating at the design tip speed ratio (TSR) during the maximum power point tracking (MPPT) process. Moreover, it has been pointed out that although a larger design TSR can increase the maximum power coefficient, it also greatly prolongs the MPPT process of VSWTs. Consequently, turbines spend more time operating at the off-design TSRs and the wind energy capture efficiency is decreased. Therefore, in the inverse aerodynamic design of VSWTs, the static aerodynamic performance (i.e., the maximum power coefficient) and the dynamic process of MPPT should be comprehensively modeled for determining an appropriate design TSR. In this paper, based on the inverse design method, an aerodynamic optimization method for VSWTs, fully considering the impacts of the design TSR on the static and dynamic behavior of wind turbines is proposed. In this method, to achieve higher wind energy production, the design TSR, chord length and twist angle are jointly optimized, which is structurally different from the conventional separated design procedure. Finally, the effectiveness of the proposed method is validated by simulation results based on the Bladed software.
Open AccessInverse Aerodynamic Optimization Considering Impacts of Design Tip Speed Ratio for Variable-Speed Wind Turbines
Because of the slow dynamic behavior of the large-inertia wind turbine rotor, variable-speed wind turbines (VSWTs) are actually unable to keep operating at the design tip speed ratio (TSR) during the maximum power point tracking (MPPT) process. Moreover, it has been pointed out that although a larger design TSR can increase the maximum power coefficient, it also greatly prolongs the MPPT process of VSWTs. Consequently, turbines spend more time operating at the off-design TSRs and the wind energy capture efficiency is decreased. Therefore, in the inverse aerodynamic design of VSWTs, the static aerodynamic performance (i.e., the maximum power coefficient) and the dynamic process of MPPT should be comprehensively modeled for determining an appropriate design TSR. In this paper, based on the inverse design method, an aerodynamic optimization method for VSWTs, fully considering the impacts of the design TSR on the static and dynamic behavior of wind turbines is proposed. In this method, to achieve higher wind energy production, the design TSR, chord length and twist angle are jointly optimized, which is structurally different from the conventional separated design procedure. Finally, the effectiveness of the proposed method is validated by simulation results based on the Bladed software.
- Open Access
A Multi-Point Method Considering the Maximum Power Point Tracking Dynamic Process for Aerodynamic Optimization of Variable-Speed Wind Turbine Blades
Due to the dynamic process of maximum power point tracking (MPPT) caused by turbulence and large rotor inertia, variable-speed wind turbines (VSWTs) cannot maintain the optimal tip speed ratio (TSR) from cut-in wind speed up to the rated speed. Therefore, in order to increase the total captured wind energy, the existing aerodynamic design for VSWT blades, which only focuses on performance improvement at a single TSR, needs to be improved to a multi-point design. In this paper, based on a closed-loop system of VSWTs, including turbulent wind, rotor, drive train and MPPT controller, the distribution of operational TSR and its description based on inflow wind energy are investigated. Moreover, a multi-point method considering the MPPT dynamic process for the aerodynamic optimization of VSWT blades is proposed. In the proposed method, the distribution of operational TSR is obtained through a dynamic simulation of the closed-loop system under a specific turbulent wind, and accordingly the multiple design TSRs and the corresponding weighting coefficients in the objective function are determined. Finally, using the blade of a National Renewable Energy Laboratory (NREL) 1.5 MW wind turbine as the baseline, the proposed method is compared with the conventional single-point optimization method using the commercial software Bladed. Simulation results verify the effectiveness of the proposed method.
Open AccessA Multi-Point Method Considering the Maximum Power Point Tracking Dynamic Process for Aerodynamic Optimization of Variable-Speed Wind Turbine Blades
Due to the dynamic process of maximum power point tracking (MPPT) caused by turbulence and large rotor inertia, variable-speed wind turbines (VSWTs) cannot maintain the optimal tip speed ratio (TSR) from cut-in wind speed up to the rated speed. Therefore, in order to increase the total captured wind energy, the existing aerodynamic design for VSWT blades, which only focuses on performance improvement at a single TSR, needs to be improved to a multi-point design. In this paper, based on a closed-loop system of VSWTs, including turbulent wind, rotor, drive train and MPPT controller, the distribution of operational TSR and its description based on inflow wind energy are investigated. Moreover, a multi-point method considering the MPPT dynamic process for the aerodynamic optimization of VSWT blades is proposed. In the proposed method, the distribution of operational TSR is obtained through a dynamic simulation of the closed-loop system under a specific turbulent wind, and accordingly the multiple design TSRs and the corresponding weighting coefficients in the objective function are determined. Finally, using the blade of a National Renewable Energy Laboratory (NREL) 1.5 MW wind turbine as the baseline, the proposed method is compared with the conventional single-point optimization method using the commercial software Bladed. Simulation results verify the effectiveness of the proposed method.