Gabriel Benedet Dutra
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Gabriel Benedet Dutra has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
César V. Franco
Department of Chemistry Federal University of Santa Catarina – UFSC Florianópolis – SC Brazil
3 shared publications- Elias Luiz de Souza
Department of Mechanical Engineering Federal University of Santa Catarina Florianópolis Brazil
3 shared publications Kleber Vieira de Paiva
Department of Mobility Engineering Federal University of Santa Catarina Joinville Brazil
3 shared publications- Mateus de Sousa Zanzi
Federal University of Santa Catarina
3 shared publications Alan Z. de Souza
Department of Chemical Engineering Federal University of Santa Catarina – UFSC Florianópolis SC Brazil
2 shared publicationsChristian Kreiner
2 shared publications
Latest Publications
- Open Access
- 21 August 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (35) , 52980-52993
Effect of Reactive Gas Composition and Duty Cycle in Low-Pressure DC-Pulsed Plasmas on the Surface Oxidation of Nitrile Rubber
Nitrile rubber (NBR) is widely used in components across several industrial sectors due to its properties that are suitable for engineering applications. Surface-environment interactions often limit performance, which depends critically on surface characteristics, especially barrier properties for sealing and membrane applications. This study investigates the effects of low-pressure direct-current pulsed plasma treatment in O2/Ar atmospheres on NBR surfaces to generate oxidized layers. Samples were treated at duty cycles of 30% and 70% with oxygen contents of 20% (low) and 80% (high). Nanoindentation post-treatment revealed increased surface contact stiffness, while differential scanning calorimetry (DSC) confirmed unchanged bulk properties. Attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy indicated the incorporation of oxidized groups and reduced C–H signals. The highest duty cycles (70%) improved sputtering species production, and the highest oxygen content (80%) enhanced O ion creation and surface oxidation, as evidenced by optical emission spectroscopy (OES) and X-ray photoelectron spectroscopy (XPS). XPS depth profiling showed a rising oxidation profile (oxygen implantation) at the treated surface. Based on a plasma-surface interaction mechanism, the condition with 80% oxygen and 30% duty cycle yields the highest surface oxidation level. It potentially enhances barrier properties, contributing to plasma-parameter optimization for tailored NBR surface modifications.
- 21 August 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (35) , 52980-52993
Open AccessEffect of Reactive Gas Composition and Duty Cycle in Low-Pressure DC-Pulsed Plasmas on the Surface Oxidation of Nitrile Rubber
Nitrile rubber (NBR) is widely used in components across several industrial sectors due to its properties that are suitable for engineering applications. Surface-environment interactions often limit performance, which depends critically on surface characteristics, especially barrier properties for sealing and membrane applications. This study investigates the effects of low-pressure direct-current pulsed plasma treatment in O2/Ar atmospheres on NBR surfaces to generate oxidized layers. Samples were treated at duty cycles of 30% and 70% with oxygen contents of 20% (low) and 80% (high). Nanoindentation post-treatment revealed increased surface contact stiffness, while differential scanning calorimetry (DSC) confirmed unchanged bulk properties. Attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy indicated the incorporation of oxidized groups and reduced C–H signals. The highest duty cycles (70%) improved sputtering species production, and the highest oxygen content (80%) enhanced O ion creation and surface oxidation, as evidenced by optical emission spectroscopy (OES) and X-ray photoelectron spectroscopy (XPS). XPS depth profiling showed a rising oxidation profile (oxygen implantation) at the treated surface. Based on a plasma-surface interaction mechanism, the condition with 80% oxygen and 30% duty cycle yields the highest surface oxidation level. It potentially enhances barrier properties, contributing to plasma-parameter optimization for tailored NBR surface modifications.
- Open Access
- 12 August 2026
- Published by Elsevier in Materials & Design
- Vol. 269
Microstructure and creep behavior of antimony containing high silver solder alloy Sn-3.9Ag-0.6Cu-3.0Sb
- 12 August 2026
- Published by Elsevier in Materials & Design
- Vol. 269
Open AccessMicrostructure and creep behavior of antimony containing high silver solder alloy Sn-3.9Ag-0.6Cu-3.0Sb
- Open Access
- 18 April 2026
- Published by Elsevier in SSRN Electronic Journal
Microstructure and creep behavior of antimony containing high silver solder alloy Sn-3.9Ag-0.6Cu-3.0Sb
Antimony containing Sn-3.9Ag-0.6Cu-3.0Sb (SAC 396+) solder alloy is a promising candidate for a high creep resistant solder alloy but is not sufficiently investigated yet. In this paper the correlation between microstructure and creep properties was investigated, using SEM, TEM, APT and XRD, as well as compression creep and nanoindentation creep tests. Microstructure investigations of pre-aged (24 h at 125 °C) bulk samples revealed that Sb is mainly dissolved in the β-Sn-matrix (Sb2Sn23, tetragonal, I41/amd), while some Sb is precipitated in form of fine SbSn particles (Sb0.49Sn0.51, rhombohedral, R-3m) in the β-Sn-matrix. Compression creep tests were performed at 35 °C, 50 °C, 85 °C, 100 °C and 125 °C with stresses between 7.5 MPa and 32.5 MPa. The stress exponents examined were found to be in the range of 7.4 to 7.5 at 100 °C or below. The stress exponent at 125 °C was lower with 4.8, indicating a mechanism change between 100 °C and 125 °C from dislocation climb controlled by pipe diffusion towards dislocation climb controlled by lattice diffusion. The activation energies were in the range between 84.7 kJ/mol and 99.6 kJ/mol. Further isothermal ageing (500 h at 125 °C) showed a decrease in creep resistance at 50 °C.
- 18 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMicrostructure and creep behavior of antimony containing high silver solder alloy Sn-3.9Ag-0.6Cu-3.0Sb
Antimony containing Sn-3.9Ag-0.6Cu-3.0Sb (SAC 396+) solder alloy is a promising candidate for a high creep resistant solder alloy but is not sufficiently investigated yet. In this paper the correlation between microstructure and creep properties was investigated, using SEM, TEM, APT and XRD, as well as compression creep and nanoindentation creep tests. Microstructure investigations of pre-aged (24 h at 125 °C) bulk samples revealed that Sb is mainly dissolved in the β-Sn-matrix (Sb2Sn23, tetragonal, I41/amd), while some Sb is precipitated in form of fine SbSn particles (Sb0.49Sn0.51, rhombohedral, R-3m) in the β-Sn-matrix. Compression creep tests were performed at 35 °C, 50 °C, 85 °C, 100 °C and 125 °C with stresses between 7.5 MPa and 32.5 MPa. The stress exponents examined were found to be in the range of 7.4 to 7.5 at 100 °C or below. The stress exponent at 125 °C was lower with 4.8, indicating a mechanism change between 100 °C and 125 °C from dislocation climb controlled by pipe diffusion towards dislocation climb controlled by lattice diffusion. The activation energies were in the range between 84.7 kJ/mol and 99.6 kJ/mol. Further isothermal ageing (500 h at 125 °C) showed a decrease in creep resistance at 50 °C.
- Open Access
- 27 September 2025
- Published by Wiley in Polymer Engineering & Science
- Vol. 65 (12) , 6781-6797
Precision in Rubber Seal Lifetime Prediction: The Critical Role of Aspect Ratio
Rubber seals are widely used in industry, with reliability assessed via aging studies adhering to international standards. However, sealing components often have high aspect ratios, with length exceeding height. This study shows how aspect ratio affects aging behavior, potentially leading to non‐representative lifetime predictions under standard conditions. NBR and EPDM rubber were submitted to thermo‐oxidative cycles with aspect ratios (AR) of 2.5, 7.5, 30, and 60 with temperatures ranging from 80°C to 170°C, and up to 180 days. Specimens were obtained from commercial gaskets and were evaluated employing compression set, indentation modulus, hardness, crosslink density, and calorimetric analyses. Under 140°C, NBR is more susceptible to aging with greater kinetics of CS evolution, hardness, crosslink density, and variation in Tg. The higher reaction rate of NBR also makes it more prone to diffusion‐limited oxidation (DLO) from a temperature of 110°C, while for EPDM, DLO only appears at 170°C. The findings indicate that higher aspect ratios present enhanced resistance to thermo‐oxidative aging due to their longer diffusive path. For the prediction of sealing component service life, sample geometry with an aspect ratio equal to or exceeding 30 is proposed. The appropriate selection of test specimens can more accurately reflect the in‐service performance of these components, reducing unnecessary maintenance and material consumption.
- 27 September 2025
- Published by Wiley in Polymer Engineering & Science
- Vol. 65 (12) , 6781-6797
Open AccessPrecision in Rubber Seal Lifetime Prediction: The Critical Role of Aspect Ratio
Rubber seals are widely used in industry, with reliability assessed via aging studies adhering to international standards. However, sealing components often have high aspect ratios, with length exceeding height. This study shows how aspect ratio affects aging behavior, potentially leading to non‐representative lifetime predictions under standard conditions. NBR and EPDM rubber were submitted to thermo‐oxidative cycles with aspect ratios (AR) of 2.5, 7.5, 30, and 60 with temperatures ranging from 80°C to 170°C, and up to 180 days. Specimens were obtained from commercial gaskets and were evaluated employing compression set, indentation modulus, hardness, crosslink density, and calorimetric analyses. Under 140°C, NBR is more susceptible to aging with greater kinetics of CS evolution, hardness, crosslink density, and variation in Tg. The higher reaction rate of NBR also makes it more prone to diffusion‐limited oxidation (DLO) from a temperature of 110°C, while for EPDM, DLO only appears at 170°C. The findings indicate that higher aspect ratios present enhanced resistance to thermo‐oxidative aging due to their longer diffusive path. For the prediction of sealing component service life, sample geometry with an aspect ratio equal to or exceeding 30 is proposed. The appropriate selection of test specimens can more accurately reflect the in‐service performance of these components, reducing unnecessary maintenance and material consumption.
- Open Access
- 20 June 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (18) , 16760-16770
Thermal Evaluation of 3D ‐Printed Triply Periodic Minimal Surface Compact Heat Exchanger Using Hexagonal Boron Nitride Photopolymeric Composite
This study reports the first investigation of the thermal behavior of compact heat exchangers (HXs) with complex geometries 3D‐printed using a photopolymeric composite as the base material. HXs with Triply Periodic Minimal Surface (TPMS) geometry were fabricated using a photopolymeric composite doped with 5 wt% hexagonal boron nitride ( h ‐BN). Mechanical characterization revealed reductions in ultimate tensile strength (41.5%) and ductility (20.5%) compared to the neat resin, whereas hardness remained comparable. Thermal analysis showed an 11.03% increase in thermal conductivity for the composite. Performance testing of the HXs demonstrated a 28.74% improvement in overall thermal conductance and a 26.25% enhancement in heat transfer compared to neat resin heat exchangers. These findings highlight the potential of h ‐BN‐doped photopolymeric composites for fabricating complex structures and advancing thermal management applications.
- 20 June 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (18) , 16760-16770
Open AccessThermal Evaluation of 3D ‐Printed Triply Periodic Minimal Surface Compact Heat Exchanger Using Hexagonal Boron Nitride Photopolymeric Composite
This study reports the first investigation of the thermal behavior of compact heat exchangers (HXs) with complex geometries 3D‐printed using a photopolymeric composite as the base material. HXs with Triply Periodic Minimal Surface (TPMS) geometry were fabricated using a photopolymeric composite doped with 5 wt% hexagonal boron nitride ( h ‐BN). Mechanical characterization revealed reductions in ultimate tensile strength (41.5%) and ductility (20.5%) compared to the neat resin, whereas hardness remained comparable. Thermal analysis showed an 11.03% increase in thermal conductivity for the composite. Performance testing of the HXs demonstrated a 28.74% improvement in overall thermal conductance and a 26.25% enhancement in heat transfer compared to neat resin heat exchangers. These findings highlight the potential of h ‐BN‐doped photopolymeric composites for fabricating complex structures and advancing thermal management applications.
- 22 December 2023
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (10)
HNBR and NBR gasket rubbers for plate heat exchangers: Thermo‐oxidative aging and service lifetime prediction
Among several available rubbers used in gaskets for plate heat exchangers, the selection of the appropriate material for each operation window is crucial. This work evaluated nitrile butadiene rubber (NBR) and hydrogenated butadiene rubber (HNBR) gaskets aged at high temperatures for up to 60 days. The properties assessed of compression set (CS), hardness, and cross‐link density demonstrated superior degradation rates for the NBR specimens. Fourier transform infrared analysis showed that the hydrogenation process predominantly affected CC double bonds. Compress stress relaxation highlighted the impact of aging on the counterforce of rubber over time. Furthermore, indentation modulus profile analysis showed heterogeneous degradation for both materials at 140°C for NBR and 170°C for HNBR. The end‐of‐life criteria of 79% CS for both materials were determined through sealing tests of the aged samples. The service lifetime prediction, using the time–temperature superposition and Arrhenius methods through the CS evolution curves, demonstrated a higher degradation resistance of HNBR gaskets, that have a superior service lifetime of at least 3.5 times at 80°C concerning those of NBR, proving a superior behavior for the hydrogenated elastomer. In addition, the evaluation of the lifetime prediction enables the verification of which rubber gasket is recommended for each operational condition in terms of material cost, service lifetime, and maintenance costs.
- 22 December 2023
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (10)
HNBR and NBR gasket rubbers for plate heat exchangers: Thermo‐oxidative aging and service lifetime prediction
Among several available rubbers used in gaskets for plate heat exchangers, the selection of the appropriate material for each operation window is crucial. This work evaluated nitrile butadiene rubber (NBR) and hydrogenated butadiene rubber (HNBR) gaskets aged at high temperatures for up to 60 days. The properties assessed of compression set (CS), hardness, and cross‐link density demonstrated superior degradation rates for the NBR specimens. Fourier transform infrared analysis showed that the hydrogenation process predominantly affected CC double bonds. Compress stress relaxation highlighted the impact of aging on the counterforce of rubber over time. Furthermore, indentation modulus profile analysis showed heterogeneous degradation for both materials at 140°C for NBR and 170°C for HNBR. The end‐of‐life criteria of 79% CS for both materials were determined through sealing tests of the aged samples. The service lifetime prediction, using the time–temperature superposition and Arrhenius methods through the CS evolution curves, demonstrated a higher degradation resistance of HNBR gaskets, that have a superior service lifetime of at least 3.5 times at 80°C concerning those of NBR, proving a superior behavior for the hydrogenated elastomer. In addition, the evaluation of the lifetime prediction enables the verification of which rubber gasket is recommended for each operational condition in terms of material cost, service lifetime, and maintenance costs.
- 12 May 2022
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 53 (4) , 2534-2546
Microstructural Characterization of an ERNiCrMo-3 and Grey Cast Iron Interface Obtained via TIG Welding
- 12 May 2022
- Published by Springer Nature in Metallurgical and Materials Transactions B
- Vol. 53 (4) , 2534-2546
Microstructural Characterization of an ERNiCrMo-3 and Grey Cast Iron Interface Obtained via TIG Welding
- Open Access
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 24 (3)
Avaliação da utilização da pós cura nas propriedades térmicas e mecânicas de um sistema epóxi de cura à temperatura ambiente
RESUMO Neste trabalho, uma resina epóxi de cura a temperatura ambiente foi submetida a ciclos térmicos de pós cura para verificar as alterações nas propriedades térmicas e mecânicas finais do material. As amostras foram obtidas por vazamento em molde metálico e os ciclos de pós cura foram realizados a 75°C, 90°C, 110°C por uma hora e um ciclo de 110°C por 2 horas. Os resultados de calorimetria exploratória diferencial (DSC) mostraram que a temperatura de transição vítrea do material (Tg ∞) não sofreu alteração significativa com a realização destes ciclos de pós cura, indicando um número de ligações cruzadas muito similar a amostra sem pós cura. Os resultados de termogravimetria (TGA) revelaram uma degradação térmica em etapas; onde cerca de 70% em massa do material sofre degradação térmica na faixa de temperaturas de 330,9°C até 345,1°C. Foi utilizado o diagrama tempo temperatura transformação (TTT) de um polímero termofixo para entendimento da cinética de cura, onde foi sugerido que a quantidade de resina e agente endurecedor teve uma influência mais significativa na cura plena da amostra do que os ciclos de pós cura adotados neste trabalho. Em termos de propriedades mecânicas, a dureza do material permaneceu inalterada com a realização dos ciclos de pós cura. Somente um grupo de amostra obteve menores valores de dureza pois o agente de cura em excesso funcionou com agente plastificante. Em termos de módulo de elasticidade, o método de vigas livres apresentou valores entre 1,72GPa e 2,18GPa, e os ciclos de pós cura não tiverem nenhuma influência notável nesta propriedade.
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 24 (3)
Open AccessAvaliação da utilização da pós cura nas propriedades térmicas e mecânicas de um sistema epóxi de cura à temperatura ambiente
RESUMO Neste trabalho, uma resina epóxi de cura a temperatura ambiente foi submetida a ciclos térmicos de pós cura para verificar as alterações nas propriedades térmicas e mecânicas finais do material. As amostras foram obtidas por vazamento em molde metálico e os ciclos de pós cura foram realizados a 75°C, 90°C, 110°C por uma hora e um ciclo de 110°C por 2 horas. Os resultados de calorimetria exploratória diferencial (DSC) mostraram que a temperatura de transição vítrea do material (Tg ∞) não sofreu alteração significativa com a realização destes ciclos de pós cura, indicando um número de ligações cruzadas muito similar a amostra sem pós cura. Os resultados de termogravimetria (TGA) revelaram uma degradação térmica em etapas; onde cerca de 70% em massa do material sofre degradação térmica na faixa de temperaturas de 330,9°C até 345,1°C. Foi utilizado o diagrama tempo temperatura transformação (TTT) de um polímero termofixo para entendimento da cinética de cura, onde foi sugerido que a quantidade de resina e agente endurecedor teve uma influência mais significativa na cura plena da amostra do que os ciclos de pós cura adotados neste trabalho. Em termos de propriedades mecânicas, a dureza do material permaneceu inalterada com a realização dos ciclos de pós cura. Somente um grupo de amostra obteve menores valores de dureza pois o agente de cura em excesso funcionou com agente plastificante. Em termos de módulo de elasticidade, o método de vigas livres apresentou valores entre 1,72GPa e 2,18GPa, e os ciclos de pós cura não tiverem nenhuma influência notável nesta propriedade.
- Open Access
- 1 December 2016
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 21 (4) , 1021-1031
Efeito dos processos de laminação sobre as propriedades físicas e mecânicas de compósitos de resina de poliéster com fibras de vidro
As propriedades dos materiais compósitos utilizados pela indústria náutica são fortemente influenciadas pelo processo de fabricação. Neste escopo, este trabalho tem o objetivo de comparar rotas usuais de processamento de embarcações de recreio - laminação manual, laminação a vácuo e infusão - através de um estudo quantitativo das propriedades físicas e mecânicas de compósitos fibra de vidro/poliéster. A metodologia adotada consistiu na confecção de corpos de prova utilizando os diferentes processos, realização de ensaios de tração e absorção de água e cálculo de densidade superficial. A infusão foi o método que apresentou melhores resultados de resistência à tração e menores valores de densidade. Os corpos de provas de laminação manual absorveram mais água do que os demais. Como conclusão, verificou-se que a relação reforço/matriz alcançada pelo processo de infusão resultou em propriedades físicas e mecânicas melhores para os laminados do que as outras rotas investigadas. A laminação a vácuo mostrou-se uma alternativa intermediária em termos de propriedades físico-mecânicas.
- 1 December 2016
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 21 (4) , 1021-1031
Open AccessEfeito dos processos de laminação sobre as propriedades físicas e mecânicas de compósitos de resina de poliéster com fibras de vidro
As propriedades dos materiais compósitos utilizados pela indústria náutica são fortemente influenciadas pelo processo de fabricação. Neste escopo, este trabalho tem o objetivo de comparar rotas usuais de processamento de embarcações de recreio - laminação manual, laminação a vácuo e infusão - através de um estudo quantitativo das propriedades físicas e mecânicas de compósitos fibra de vidro/poliéster. A metodologia adotada consistiu na confecção de corpos de prova utilizando os diferentes processos, realização de ensaios de tração e absorção de água e cálculo de densidade superficial. A infusão foi o método que apresentou melhores resultados de resistência à tração e menores valores de densidade. Os corpos de provas de laminação manual absorveram mais água do que os demais. Como conclusão, verificou-se que a relação reforço/matriz alcançada pelo processo de infusão resultou em propriedades físicas e mecânicas melhores para os laminados do que as outras rotas investigadas. A laminação a vácuo mostrou-se uma alternativa intermediária em termos de propriedades físico-mecânicas.