Junsik Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Junsik Lee has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Cheoljoong Kim
KAIST (Korea, Republic of)
4 shared publicationsDooseub Shin
KAIST (Korea, Republic of)
4 shared publicationsJee Hoon Sim
Korea Advanced Institue of Science and Technology (Korea, Republic of)
4 shared publicationsJunoh Kim
Korea Advanced Institue of Science and Technology (Korea, Republic of)
4 shared publications- Yong Hyub Won
Korea Advanced Institute of Science and Technology
4 shared publications Gyo Hyun Koo
Korea Advanced Institue of Science and Technology (Korea, Republic of)
2 shared publications
Latest Publications
- 4 December 2019
- Published by Optica Publishing Group in Optics Express
- Vol. 27 (25) , 36757-36766
Nonmechanical three-dimensional beam steering using electrowetting-based liquid lens and liquid prism
In this paper, we present a system for nonmechanical three-dimensional beam steering using an electrowetting based liquid lens and liquid prism. The optical design of the presented system was modeled with Zemax and three-dimensional beam steering was simulated by changing the ROC of the lens and the apex angle of the prism. The liquid lens from Corning-Varioptic was used and the liquid prism was fabricated and these were combined. The liquid lens and liquid prism were filled with two immiscible liquids whose densities are the same. The liquid lens provides variable focal lengths as the applied voltage is changed. The diopter range of the liquid lens is from −3.9 D to 14.5 D. Beam steering on the x-axis, y-axis, and xy-axis was achieved by applying different voltages to four sidewalls of the liquid prism. The liquid prism has a beam steering angle of up to 11.6 °, 12 °, and 11.8 ° on x-axis, y-axis, and xy-axis, respectively. By combining the electrowetting actuated liquid lens and liquid prism, three-dimensional beam steering control including the z-axis direction was demonstrated.
- 4 December 2019
- Published by Optica Publishing Group in Optics Express
- Vol. 27 (25) , 36757-36766
Nonmechanical three-dimensional beam steering using electrowetting-based liquid lens and liquid prism
In this paper, we present a system for nonmechanical three-dimensional beam steering using an electrowetting based liquid lens and liquid prism. The optical design of the presented system was modeled with Zemax and three-dimensional beam steering was simulated by changing the ROC of the lens and the apex angle of the prism. The liquid lens from Corning-Varioptic was used and the liquid prism was fabricated and these were combined. The liquid lens and liquid prism were filled with two immiscible liquids whose densities are the same. The liquid lens provides variable focal lengths as the applied voltage is changed. The diopter range of the liquid lens is from −3.9 D to 14.5 D. Beam steering on the x-axis, y-axis, and xy-axis was achieved by applying different voltages to four sidewalls of the liquid prism. The liquid prism has a beam steering angle of up to 11.6 °, 12 °, and 11.8 ° on x-axis, y-axis, and xy-axis, respectively. By combining the electrowetting actuated liquid lens and liquid prism, three-dimensional beam steering control including the z-axis direction was demonstrated.
- 20 February 2017
- Published by SPIE-Intl Soc Optical Eng
- p. 1011512-1011512-9
Fabrication of electro-wetting liquid lenticular lens by using diffuser
- 20 February 2017
- Published by SPIE-Intl Soc Optical Eng
- p. 1011512-1011512-9
Fabrication of electro-wetting liquid lenticular lens by using diffuser
- 20 February 2017
- Published by SPIE-Intl Soc Optical Eng
- p. 101160B-101160B-6
A fabrication method of opened structures for uniform liquid dosing in liquid lenticular systems
- 20 February 2017
- Published by SPIE-Intl Soc Optical Eng
- p. 101160B-101160B-6
A fabrication method of opened structures for uniform liquid dosing in liquid lenticular systems
- 20 February 2017
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10116, 1011609
Low voltage electrowetting lenticular lens by using multilayer dielectric structure
Lenticular type multi-view display is one of the most popular ways for implementing three dimensional display. This method has a simple structure and exhibits a high luminance. However, fabricating the lenticular lens is difficult because it requires optically complex calculations. 2D-3D conversion is also impossible due to the fixed shape of the lenticular lens. Electrowetting based liquid lenticular lens has a simple fabrication process compared to the solid lenticular lens and the focal length of the liquid lenticular lens can be changed by applying the voltage. 3D and 2D images can be observed with a convex and a flat lens state respectively. Despite these advantages, the electrowetting based liquid lenticular lens demands high driving voltage and low breakdown voltage with a single dielectric layer structure. A certain degree of thickness of the dielectric layer is essential for a uniform operation and a low degradation over time. This paper presents multilayer dielectric structure which results in low driving voltage and the enhanced dielectric breakdown. Aluminum oxide (Al2O3), silicon oxide (SiO2) and parylene C were selected as the multilayer insulators. The total thickness of the dielectric layer of all samples was the same. This method using the multilayer dielectric structure can achieve the lower operating voltage than when using the single dielectric layer. We compared the liquid lenticular lens with three kinds of the multilayer dielectric structure to one with the parylene C single dielectric layer in regard to operational characteristics such as the driving voltage and the dielectric breakdown. © (2017) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.
- 20 February 2017
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10116, 1011609
Low voltage electrowetting lenticular lens by using multilayer dielectric structure
Lenticular type multi-view display is one of the most popular ways for implementing three dimensional display. This method has a simple structure and exhibits a high luminance. However, fabricating the lenticular lens is difficult because it requires optically complex calculations. 2D-3D conversion is also impossible due to the fixed shape of the lenticular lens. Electrowetting based liquid lenticular lens has a simple fabrication process compared to the solid lenticular lens and the focal length of the liquid lenticular lens can be changed by applying the voltage. 3D and 2D images can be observed with a convex and a flat lens state respectively. Despite these advantages, the electrowetting based liquid lenticular lens demands high driving voltage and low breakdown voltage with a single dielectric layer structure. A certain degree of thickness of the dielectric layer is essential for a uniform operation and a low degradation over time. This paper presents multilayer dielectric structure which results in low driving voltage and the enhanced dielectric breakdown. Aluminum oxide (Al2O3), silicon oxide (SiO2) and parylene C were selected as the multilayer insulators. The total thickness of the dielectric layer of all samples was the same. This method using the multilayer dielectric structure can achieve the lower operating voltage than when using the single dielectric layer. We compared the liquid lenticular lens with three kinds of the multilayer dielectric structure to one with the parylene C single dielectric layer in regard to operational characteristics such as the driving voltage and the dielectric breakdown. © (2017) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.
- Open Access
- 16 December 2016
- Published by Optica Publishing Group in Optics Express
- Vol. 24 (26) , 29972-29983
Improving the performance of an electrowetting lenticular lens array by using a thin polycarbonate chamber
In this paper, we used a thin polycarbonate (PC) chamber to improve the performance of an electrowetting lenticular lens array. The polycarbonate chamber changed the radius of curvature (ROC) of the oil acting as a lens, which increased the dioptric power of the liquid lens to 1666.7D. The increase in dioptric power required a reduction in the distance between the optical center of the lens and the display pixels under the chamber, which was accomplished by reducing the thickness of the chamber. The optimal thickness of the chamber was determined to be 0.5mm. Using this thin PC chamber, transmittance and viewing angle were measured and compared with an electrowetting lenticular lens with a conventional 1mm poly methyl methacrylate (PMMA) chamber was done. Crosstalk which degrades clear 3D images, is an inevitable factor in lenticular lens type multi-view systems. With the 0.5mm PC chamber, the viewing zone was expanded and the ratio of the crosstalk area was reduced, which resulted in a clear 3D image. The new method of depositing the electrode layer also ensured the uniform operation of the liquid lens array.
- 16 December 2016
- Published by Optica Publishing Group in Optics Express
- Vol. 24 (26) , 29972-29983
Open AccessImproving the performance of an electrowetting lenticular lens array by using a thin polycarbonate chamber
In this paper, we used a thin polycarbonate (PC) chamber to improve the performance of an electrowetting lenticular lens array. The polycarbonate chamber changed the radius of curvature (ROC) of the oil acting as a lens, which increased the dioptric power of the liquid lens to 1666.7D. The increase in dioptric power required a reduction in the distance between the optical center of the lens and the display pixels under the chamber, which was accomplished by reducing the thickness of the chamber. The optimal thickness of the chamber was determined to be 0.5mm. Using this thin PC chamber, transmittance and viewing angle were measured and compared with an electrowetting lenticular lens with a conventional 1mm poly methyl methacrylate (PMMA) chamber was done. Crosstalk which degrades clear 3D images, is an inevitable factor in lenticular lens type multi-view systems. With the 0.5mm PC chamber, the viewing zone was expanded and the ratio of the crosstalk area was reduced, which resulted in a clear 3D image. The new method of depositing the electrode layer also ensured the uniform operation of the liquid lens array.