Kaushal Kumar
Research Subjects
Kaushal Kumar has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
Arun Kumar
J.C. Bose University of Science and Technology, YMCA
7 shared publications- Ravindra Kumar
Department of Mechanical Engineering, Shri Ram Murti Smarak College of Engineering and Technology, Bareilly, India
3 shared publications Sudhir Kumar
Metallurgical and Materials Engineering, Indian Institute of Technology Roorkee, Roorkee, INDIA
3 shared publicationsPooja Singh
J.C. Bose University of Science and Technology, YMCA
2 shared publications- Prakriti Kumar Ghosh
Indian Institute of Technology Roorkee
2 shared publications Ramkishor Anant
Department of Metallurgical and Materials Engineering Indian Institute of Technology, Roorkee Roorkee 247667 India
2 shared publications
Latest Publications
- 1 June 2026
- Published by SAGE Publications in Materials Science and Technology
Static and dynamic mechanical behaviour of low loading MWCNT-epoxy nanocomposites
High-performance carbonaceous nanofiller (MWCNT) reinforced epoxy nanocomposites at different compositions were synthesized using the ultrasonication dual mixing method. The static and dynamic mechanical properties of the nanocomposites were examined. At 0.8 wt.% of nanofiller, the epoxy nanocomposite greatly improved in tensile strength by about 22.1% and Young's modulus by about 18.5%. The dynamic mechanical analysis showed a significant improvement in the storage modulus of about 19.1% and glass transition temperature of about 15.1% of the epoxy nanocomposite. This improvement may be attributed to the formation of an effective interface between the epoxy and MWCNT. The static and dynamic mechanical properties of the epoxy matrix were significantly improved as a result of the homogenous dispersion of carbonaceous filler in the epoxy matrix.
- 1 June 2026
- Published by SAGE Publications in Materials Science and Technology
Static and dynamic mechanical behaviour of low loading MWCNT-epoxy nanocomposites
High-performance carbonaceous nanofiller (MWCNT) reinforced epoxy nanocomposites at different compositions were synthesized using the ultrasonication dual mixing method. The static and dynamic mechanical properties of the nanocomposites were examined. At 0.8 wt.% of nanofiller, the epoxy nanocomposite greatly improved in tensile strength by about 22.1% and Young's modulus by about 18.5%. The dynamic mechanical analysis showed a significant improvement in the storage modulus of about 19.1% and glass transition temperature of about 15.1% of the epoxy nanocomposite. This improvement may be attributed to the formation of an effective interface between the epoxy and MWCNT. The static and dynamic mechanical properties of the epoxy matrix were significantly improved as a result of the homogenous dispersion of carbonaceous filler in the epoxy matrix.
- 7 May 2024
- Published by IOP Publishing in Engineering Research Express
- Vol. 6 (2) , 025522
Viscoelastic behaviour of yttrium oxide and reduced graphene oxide embedded epoxy nanocomposite
In this work, two different types of nanofillers yttrium oxide (Y2O3) or yttria and reduced graphene oxide (RGO) are used to reinforce with epoxy polymer for the synthesis of epoxy nanocomposites by using the ultrasonication dual mixing approach. Raman spectroscopy has been done to analyze the microstructure of yttria and conformation of the formed RGO from Graphene oxide. The viscoelastic behavior of epoxy nanocomposites is evaluated with the help of the dynamic mechanical analyzer. Further Storage modulus is used to determine the cross-link density ‘νe’, coefficient of effectiveness ‘C factor’, and reinforcement efficiency factor ‘r factor’. The damping coefficient (Tan δ) helps in determining the glass transition temperature of the epoxy and its nanocomposites. The results demonstrate that at 1.6 wt% Y2O3 & 0.8 wt% RGO reinforcement in pure epoxy matrix showed maximum enhancement in terms of storage modulus, loss modulus, and glass transition temperature. The semi-circular shape that resulted from the study of the Cole-Cole plot of all the nanocomposites demonstrated the homogenous dispersion of nanoparticles and efficient bonding between epoxy and nanoparticles. Field Emission Scanning Electron Microscopy (FESEM) has been used to identify the interfacial interaction between nanoparticle and epoxy matrix through tensile fracture surfaces.
- 7 May 2024
- Published by IOP Publishing in Engineering Research Express
- Vol. 6 (2) , 025522
Viscoelastic behaviour of yttrium oxide and reduced graphene oxide embedded epoxy nanocomposite
In this work, two different types of nanofillers yttrium oxide (Y2O3) or yttria and reduced graphene oxide (RGO) are used to reinforce with epoxy polymer for the synthesis of epoxy nanocomposites by using the ultrasonication dual mixing approach. Raman spectroscopy has been done to analyze the microstructure of yttria and conformation of the formed RGO from Graphene oxide. The viscoelastic behavior of epoxy nanocomposites is evaluated with the help of the dynamic mechanical analyzer. Further Storage modulus is used to determine the cross-link density ‘νe’, coefficient of effectiveness ‘C factor’, and reinforcement efficiency factor ‘r factor’. The damping coefficient (Tan δ) helps in determining the glass transition temperature of the epoxy and its nanocomposites. The results demonstrate that at 1.6 wt% Y2O3 & 0.8 wt% RGO reinforcement in pure epoxy matrix showed maximum enhancement in terms of storage modulus, loss modulus, and glass transition temperature. The semi-circular shape that resulted from the study of the Cole-Cole plot of all the nanocomposites demonstrated the homogenous dispersion of nanoparticles and efficient bonding between epoxy and nanoparticles. Field Emission Scanning Electron Microscopy (FESEM) has been used to identify the interfacial interaction between nanoparticle and epoxy matrix through tensile fracture surfaces.
- 29 March 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (5) , 3706-3716
A Comparative Study on Mechanical Properties of Yttrium Oxide and Reduced Graphene Oxide Reinforced Epoxy Nanocomposites
- 29 March 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (5) , 3706-3716
A Comparative Study on Mechanical Properties of Yttrium Oxide and Reduced Graphene Oxide Reinforced Epoxy Nanocomposites
- 7 February 2024
- Published by IOP Publishing in Modelling and Simulation in Materials Science and Engineering
- Vol. 32 (3) , 035005
Performance evaluation of 2D MoS2-based solar cells and realization of transparent ultra-thin devices
Molybdenum disulfide (MoS2) is an alternate absorber layer in 2D solar cells owing to its potential of proficient sunlight harvesting. The optimum electrical and optical properties of MoS2 validate it as a suitable photovoltaic absorber material. This work investigates the performance of 2D (and multi-layer) MoS2-based vertically stacked solar cell by numerical simulation process using one dimensional solar cell capacitance simulator (SCAPS). Two device configurations based on Schottky junction (ITO/n-MoS2/Au) and pn junction (ITO/n-MoS2/p-MoS2/Au) have been theoretically analyzed. The feasibility of ultra-thin transparent solar cells is also demonstrated, which is motivating from a technological outlook. Initially, the properties of the active layers are optimized to give the highest performance. The findings are explained on the basis of band alignment between the electrodes and the different layers. The potential barrier developed at the interface of different materials governs the output of the cells. The calculations forecast the material properties, which need to be tuned to fabricate solar cells with enhanced efficiency. After optimization, the highest efficiency obtained for single n-MoS2-based solar cell is 10.22%, while for the pn junction solar cell it is 16.86%. The optimized cells exhibit high open circuit voltages of ∼1.2 V, which is an essential factor for commercial realization of solar cells. Lastly, the performance of transparent solar cells based on thin 2D MoS2 films has been predicted which showcases the efficiency in the range of 0.78%–4.36%. These homo-junction device investigations of solely MoS2 layer along with employment of a strict control on the defects during deposition and fabrication of MoS2-based solar cells can ensure better performance of the device. Thus, it can open ways to develop next generation feasible solar cells with higher power density as compared to existing technology.
- 7 February 2024
- Published by IOP Publishing in Modelling and Simulation in Materials Science and Engineering
- Vol. 32 (3) , 035005
Performance evaluation of 2D MoS2-based solar cells and realization of transparent ultra-thin devices
Molybdenum disulfide (MoS2) is an alternate absorber layer in 2D solar cells owing to its potential of proficient sunlight harvesting. The optimum electrical and optical properties of MoS2 validate it as a suitable photovoltaic absorber material. This work investigates the performance of 2D (and multi-layer) MoS2-based vertically stacked solar cell by numerical simulation process using one dimensional solar cell capacitance simulator (SCAPS). Two device configurations based on Schottky junction (ITO/n-MoS2/Au) and pn junction (ITO/n-MoS2/p-MoS2/Au) have been theoretically analyzed. The feasibility of ultra-thin transparent solar cells is also demonstrated, which is motivating from a technological outlook. Initially, the properties of the active layers are optimized to give the highest performance. The findings are explained on the basis of band alignment between the electrodes and the different layers. The potential barrier developed at the interface of different materials governs the output of the cells. The calculations forecast the material properties, which need to be tuned to fabricate solar cells with enhanced efficiency. After optimization, the highest efficiency obtained for single n-MoS2-based solar cell is 10.22%, while for the pn junction solar cell it is 16.86%. The optimized cells exhibit high open circuit voltages of ∼1.2 V, which is an essential factor for commercial realization of solar cells. Lastly, the performance of transparent solar cells based on thin 2D MoS2 films has been predicted which showcases the efficiency in the range of 0.78%–4.36%. These homo-junction device investigations of solely MoS2 layer along with employment of a strict control on the defects during deposition and fabrication of MoS2-based solar cells can ensure better performance of the device. Thus, it can open ways to develop next generation feasible solar cells with higher power density as compared to existing technology.
- 27 August 2021
- Published by Wiley in Polymer Composites
- Vol. 42 (11) , 6000-6009
Improved mechanical performance and unique toughening mechanisms of UDM processed epoxy‐SiO2 nanocomposites
This work demonstrates improved mechanical performance and unique toughening mechanisms of ultrasonic dual mixing (UDM) processed epoxy‐SiO2 nanocomposites. The loading of SiO2 nanoparticles in the epoxy matrix was varied from 1 to 5 vol% to produce the nanocomposites. The mechanical performance was evaluated by measuring the tensile and fracture properties of the nanocomposites. An optimal nanoparticle loading of 3 vol% in epoxy was found vital for improved performance of the nanocomposite. The optimal nanoparticle loading in epoxy lead to an increase of 18.45% in tensile strength and 120% increase in fracture toughness (GIC) compared to the neat epoxy. The fracture surface analysis revealed various toughening mechanisms including particle pull out, plastic void growth, plastic deformation, and crack deflection along with a unique mechanism of strong interfacial bonding between SiO2 particle and epoxy matrix.
- 27 August 2021
- Published by Wiley in Polymer Composites
- Vol. 42 (11) , 6000-6009
Improved mechanical performance and unique toughening mechanisms of UDM processed epoxy‐SiO2 nanocomposites
This work demonstrates improved mechanical performance and unique toughening mechanisms of ultrasonic dual mixing (UDM) processed epoxy‐SiO2 nanocomposites. The loading of SiO2 nanoparticles in the epoxy matrix was varied from 1 to 5 vol% to produce the nanocomposites. The mechanical performance was evaluated by measuring the tensile and fracture properties of the nanocomposites. An optimal nanoparticle loading of 3 vol% in epoxy was found vital for improved performance of the nanocomposite. The optimal nanoparticle loading in epoxy lead to an increase of 18.45% in tensile strength and 120% increase in fracture toughness (GIC) compared to the neat epoxy. The fracture surface analysis revealed various toughening mechanisms including particle pull out, plastic void growth, plastic deformation, and crack deflection along with a unique mechanism of strong interfacial bonding between SiO2 particle and epoxy matrix.
- 4 December 2020
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 30 (1) , 145-153
Enhanced Thermomechanical Properties of ZrO2 Particle Reinforced Epoxy Nanocomposite
- 4 December 2020
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 30 (1) , 145-153
Enhanced Thermomechanical Properties of ZrO2 Particle Reinforced Epoxy Nanocomposite
- 17 July 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (9) , 096503
SMA, GTA and P-GMA dissimilar weld joints of 304LN stainless steel to HSLA steel; Part-2: hot corrosion kinetics
A study of hot corrosion kinetics of dissimilar weld joints of 304LN austenitic stainless steel and HSLA steel, which are welded by commonly used arc welding processes such as P-GMAW (pulsed current gas metal arc welding), GTAW (tungsten inert gas welding), and SMAW (shielded metal arc welding), has been conducted. The joints were then exposed to a molten salt environment of K2SO4 + NaCl (50%) at 923 K (650 oC) under cyclic conditions, that is, 1 hr of heating and subsequently 20min of cooling. A gravimetric analysis was conducted and it was observed that salt-coated samples follow a parabolic rate law. SEM/EDAX, XRD, and line mapping were used to systematically characterize the resulting oxide scale in the dissimilar weld joints. The influence of the molten salt environment on the hot corrosion behavior of dissimilar welded specimens is also discussed. From the hot corrosion studies, it was concluded that the longer the duration of exposure to molten salt, the higher the weight gain by the weldment.
- 17 July 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 5 (9) , 096503
SMA, GTA and P-GMA dissimilar weld joints of 304LN stainless steel to HSLA steel; Part-2: hot corrosion kinetics
A study of hot corrosion kinetics of dissimilar weld joints of 304LN austenitic stainless steel and HSLA steel, which are welded by commonly used arc welding processes such as P-GMAW (pulsed current gas metal arc welding), GTAW (tungsten inert gas welding), and SMAW (shielded metal arc welding), has been conducted. The joints were then exposed to a molten salt environment of K2SO4 + NaCl (50%) at 923 K (650 oC) under cyclic conditions, that is, 1 hr of heating and subsequently 20min of cooling. A gravimetric analysis was conducted and it was observed that salt-coated samples follow a parabolic rate law. SEM/EDAX, XRD, and line mapping were used to systematically characterize the resulting oxide scale in the dissimilar weld joints. The influence of the molten salt environment on the hot corrosion behavior of dissimilar welded specimens is also discussed. From the hot corrosion studies, it was concluded that the longer the duration of exposure to molten salt, the higher the weight gain by the weldment.
- Open Access
- 1 January 2018
- Published by Elsevier in Ultrasonics Sonochemistry
- Vol. 40, 784-790
UDM enhanced physical and mechanical properties through the formation of nanocavities in an epoxy matrix
- 1 January 2018
- Published by Elsevier in Ultrasonics Sonochemistry
- Vol. 40, 784-790
Open AccessUDM enhanced physical and mechanical properties through the formation of nanocavities in an epoxy matrix
- 1 February 2017
- Published by Wiley in Polymer Composites
- Vol. 39 (8) , 2889-2896
Viscoelastic and thermally stable PDMS–SiO2 filled epoxy adhesive joint on steel substrate
The epoxy based composite adhesives have been prepared by reinforcing polydimethylsiloxane (PDMS) treated SiO2 nanoparticle with varying content of 2, 4, and 6 wt% in comparison of neat epoxy. PDMS treated SiO2/epoxy composites are fabricated using an ultrasonic mixing process. Dynamic mechanical analysis has been carried out to evaluate the viscoelastic properties on every group of the epoxy composite. The effect of PDMS treated SiO2 nanoparticles reinforcement on viscoelastic properties of epoxy resin have been studied in the terms of storage modulus and tanδ values with respect to temperature. The dispersion conditions of the PDMS–SiO2 nanoparticles in epoxy adhesive have been identified by field emission scanning electron microscopy (FESEM). Thermal gravimetric analysis has been used to identify the thermal stability of each group of PDMS–SiO2/epoxy composite. The effect of PDMS–SiO2/epoxy composite adhesive on the lap joints of mechanically treated mild steel substrate has also been investigated. POLYM. COMPOS., 39:2889–2896, 2018. © 2017 Society of Plastics Engineers
- 1 February 2017
- Published by Wiley in Polymer Composites
- Vol. 39 (8) , 2889-2896
Viscoelastic and thermally stable PDMS–SiO2 filled epoxy adhesive joint on steel substrate
The epoxy based composite adhesives have been prepared by reinforcing polydimethylsiloxane (PDMS) treated SiO2 nanoparticle with varying content of 2, 4, and 6 wt% in comparison of neat epoxy. PDMS treated SiO2/epoxy composites are fabricated using an ultrasonic mixing process. Dynamic mechanical analysis has been carried out to evaluate the viscoelastic properties on every group of the epoxy composite. The effect of PDMS treated SiO2 nanoparticles reinforcement on viscoelastic properties of epoxy resin have been studied in the terms of storage modulus and tanδ values with respect to temperature. The dispersion conditions of the PDMS–SiO2 nanoparticles in epoxy adhesive have been identified by field emission scanning electron microscopy (FESEM). Thermal gravimetric analysis has been used to identify the thermal stability of each group of PDMS–SiO2/epoxy composite. The effect of PDMS–SiO2/epoxy composite adhesive on the lap joints of mechanically treated mild steel substrate has also been investigated. POLYM. COMPOS., 39:2889–2896, 2018. © 2017 Society of Plastics Engineers
- 28 November 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (114) , 113405-113414
Anticorrosive and electromagnetic shielding response of a graphene/TiO2–epoxy nanocomposite with enhanced mechanical properties
Fabrication of structurally strong and thermally stable hybrid nanocomposites based on graphene/TiO2/epoxy with improved anticorrosive and EMI shielding properties is reported.
- 28 November 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (114) , 113405-113414
Anticorrosive and electromagnetic shielding response of a graphene/TiO2–epoxy nanocomposite with enhanced mechanical properties
Fabrication of structurally strong and thermally stable hybrid nanocomposites based on graphene/TiO2/epoxy with improved anticorrosive and EMI shielding properties is reported.